| Age | Commit message (Collapse) | Author |
|---|
|
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
T1023 and T1024 have 4 SerDes lanes. Fix macro SRDS_MAX_LANES
and use this macro instead of hard-coded value in t1024_serdes.c.
Signed-off-by: Paulo Zaneti <[email protected]>
Signed-off-by: York Sun <[email protected]>
|
|
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The symbol CONFIG_OMAP_VC_I2C_HS_MCODE always uses the default value.
Restructure the comment and code such that if a need arises later to use
another value we can address this then.
Signed-off-by: Tom Rini <[email protected]>
|
|
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot. select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: Tom Rini <[email protected]>
|
|
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there. Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely. The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file. Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: Tom Rini <[email protected]>
|
|
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead. With that
changed we can drop all defines of CONFIG_OMAP. While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.
Signed-off-by: Tom Rini <[email protected]>
|
|
This code has been unused since the removal of the "omap2" platforms,
remove.
Signed-off-by: Tom Rini <[email protected]>
|
|
The SMPEN bit is located in the cpuectlr_el1 register and not the
cpuactlr_el1 register. Adjust the comment accordingly and also fix
a spelling error.
Signed-off-by: Dinh Nguyen <[email protected]>
CC: Mingkai Hu <[email protected]>
CC: Gong Qianyu <[email protected]>
CC: Mateusz Kulikowski <[email protected]>
CC: Hou Zhiqiang <[email protected]>
CC: York Sun <[email protected]>
CC: Albert Aribaud <[email protected]>
CC: Masahiro Yamada <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Drop use of this long-deprecated option for powerpc.
Signed-off-by: Simon Glass <[email protected]>
|
|
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <[email protected]>
|
|
|
|
Change tbu/l type to unsigned int.
>From the timer file for arm,
"(((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;" is used,
This piece code is based on tbu/tbl is 32bits, so change the type to
unsigned int.
Signed-off-by: Peng Fan <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The variable grf is only referenced if EARLY_DEBUG is defined so move the
declaration to be under the existing guard.
Cc: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
For early debug, the following configs needs to be enabled:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_BASE=0x44e09000
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
For early debug, the following configs needs to be enabled:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y
For DRA7xx:
CONFIG_DEBUG_UART_BASE=0x4806a000
For AM57xx:
CONFIG_DEBUG_UART_BASE=0x48020000
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:
MPU values for PG 2.0 and later(Package ZCZ and ZCE):
-------------------------------------------------------
| | ZCZ | ZCE |
|-------------------------------------------------------|
| | VDD[V] | ARM [MHz] | VDD[V] | ARM [MHz] |
|-------|----------|------------|----------|------------|
| NITRO | 1.325 | 1000 | NA | NA |
|-------|----------|------------|----------|------------|
| TURBO | 1.26 | 800 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP120 | 1.20 | 720 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP100 | 1.10 | 600 | 1.10 | 600 |
|-------|----------|------------|----------|------------|
| OPP50 | 0.95 | 300 | 0.95 | 300 |
-------------------------------------------------------
There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.
[1] http://www.ti.com/lit/ds/symlink/am3356.pdf
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This configuration should be valid for all F7 family devices in general.
Here is the regions info:
- Region0 : 4GB : cacheable & executable.
- Region1 : 512MB : text area : strogly ordered & executable.
- Region2 : 512MB : peripherals : device memory & non-executable.
- Region3 : 512MB : peripherals : device memory & non-executable.
- Region4 : 512MB : cortexM area: strongly ordered & non-executable.
Higher region number overrides the lower region configuration.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Cortex-M archs support option memory protection unit (MPU). MPU is used
to set the memory types, attributes, access permissions for different regions,
cache policies of the device.
e.g. using MPU it is possible to configure memory region as device memory
or strongly ordered, memory attributes like execute never, cache policies
like write-back or write-through.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Data cache memory needs to be disabled before handing over control to
linux kernel. This patch populates the cleanup_before_linux stub.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Add functionality to flush & invalidate all the dcache using the
prototype declared in common header file.
Signed-off-by: Vikas Manocha <[email protected]>
[trini: Add dummy functions for the not-enabled case]
Signed-off-by: Tom Rini <[email protected]>
|
|
The boston memory map isn't suited to the simple "all memory starting
from 0" approach that the MIPS arch_fixup_fdt() implementation takes.
Instead we need to indicate the first 256MiB of DDR from 0 and the rest
from 0x90000000. Implement ft_board_setup to do that.
Signed-off-by: Paul Burton <[email protected]>
Signed-off-by: Daniel Schwierzeck <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Move the MIPS Coherence Manager (CM) Global Configuration Registers
(GCRs) away from the region of the physical address space which the
Boston board's parallel flash is found in, such that we can access all
of flash without clobbering GCRs.
Signed-off-by: Paul Burton <[email protected]>
Signed-off-by: Daniel Schwierzeck <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Without adding a prompt for CONFIG_MIPS_CM_BASE, Kconfig doesn't allow
defconfigs to set it. Provide the prompt in order to allow for that.
Signed-off-by: Paul Burton <[email protected]>
Signed-off-by: Daniel Schwierzeck <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Fixes commit a186d26, which missed including SFR NeufBox config from bmips
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
|
|
Shrink brcm,bcm6328-mc size to avoid overlapping with other controllers
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
|
|
Shrink brcm,bcm6328-mc size to avoid overlapping with other controllers
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
|
|
Shrink brcm,bcm6358-mc size to avoid overlapping with other controllers
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
|
|
am335x_evm SPL is very close to its limit in SRAM space.
Switch to use tiny printf to reclaim some size.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Enable SPL_DM on all AM335x based TI platforms.
http://patchwork.ozlabs.org/patch/751300/
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
No reason to use a separate load script for am33xx than using
omap-common load script.
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This is to aid platforms that uses OF_PLATDATA.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Adding support for fdt fixup to update the
memory node in device tree for falcon boot.
This is needed for single stage or falcon
bootmode, to pass memory configuration to
kernel through DT memory node.
Signed-off-by: Ravi Babu <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
Declare the size of ddr very early in spl, so that this can be
used to enable cache.
Signed-off-by: Lokesh Vutla <[email protected]>
Signed-off-by: Ravi Babu <[email protected]>
|
|
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
This should be uint64_t to match its definition in common.h. Fix it.
Signed-off-by: Simon Glass <[email protected]>
|
|
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
|
|
|
|
Add mipi dsi configuration for evb-rk3288 device tree.
Signed-off-by: Eric Gao <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add grf register define for rk3288 mipi dsi
Signed-off-by: Eric Gao <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add dts config for mipi display, include vop, mipi controller, panel, backlight
. And Enable rk808 for lcd_3v3 in another patch.
Signed-off-by: Eric Gao <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
Add mipi display mode for rk3399 vop, so that we can use mipi panel
for display.
Signed-off-by: Eric Gao <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add basic driver for mipi display on rockchip soc platform.
Signed-off-by: Eric Gao <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Add GRF register declaration for mipi dsi.
Signed-off-by: Eric Gao <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.
Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`
Signed-off-by: Jacob Chen <[email protected]>
|
