| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Enable/disable the usb host phy on the odroid U/X2 boards which are based
on the Exynos4412 SOC.
Signed-off-by: Suriyan Ramasami <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
The current vbus GPIOs on snow make very little sense, their number is
far above the maximum. As a result, USB doesn't work on snow.
Correct the GPIO numbering so they match the current scheme for exynos5.
Tested both EHCI and XHCI to correctly work after this change.
Signed-off-by: Sjoerd Simons <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Exynos5800 IROM has a different, from 5250 and 5420, prototype of the
usb_copy() function. Luckily the earlier version did not expect any
arguments, which means the same code could be used with old and new
SoCs, the old ones just ignoring the arguments.
Signed-off-by: Vadim Bendebury <[email protected]>
Signed-off-by: Akshay Saraswat <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Add a 4G configuration and choose it based on the number of banks
declared in config file. A board with 4 SDRAM banks declared (as
per CONFIG_NR_DRAM_BANKS) will end up with the 2G confiuration.
Signed-off-by: Doug Anderson <[email protected]>
Signed-off-by: Akshay Saraswat <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
As per Exynos5800 UM ver 0.00 section 17.13.2.1
CONCONTROL register bit 3 [update_mode], Exynos5800 does not
support the PHY initiated update. And it is recommanded to
set this field to 1'b1 during initialization. This patch sets this bit.
Applying MC-initiated mode makes DDL tracking ON, that helps in
compensate MIF voltage variation.
Signed-off-by: Alim Akhtar <[email protected]>
Signed-off-by: Doug Anderson <[email protected]>
Signed-off-by: Akshay Saraswat <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This adds following things :
- New config and defconfig for Peach-Pi board.
- Alterations in Kconfig and MAINTAINERS.
- Addition of CONFIG_EXYNOS5800.
- ADdition of exynos5800-peach-pi in dts list.
Signed-off-by: Akshay Saraswat <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
We have a new board Peach-Pi similar to Peach-Pit. Peach-Pi
differs from Peach-Pit in configuration factors like display
resolution, memory size, SoC version etc.
Signed-off-by: Alim Akhtar <[email protected]>
Signed-off-by: Akshay Saraswat <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch intends to add a new proid for Exynos5800 which is a
variant of Exynos5420. Product id for Exynos5800 is 0x5422.
Both Exynos5420 and Exynos5800 are pin to pin compitable. This
gives us an advantage of reusing Exynos5420 clock, pinmux, memory
and other settings.
Signed-off-by: Alim Akhtar <[email protected]>
Signed-off-by: Akshay Saraswat <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This moves SH_32BIT to Kconfig, and removes SH_32BIT from config
files.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
|
|
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Ye Li <[email protected]>
|
|
The argument boot_flags of board_init_f() is not used at all in the
powerpc specific board.c init sequence. Now with the generic init
sequence, this boot_flags arg is used by board_init_f().
This patch sets the r3 register that is used to pass the boot_flags
argument from the start.S board_init_f() call to 0 prior to the function
call to avoid unknown content to end up in gd->flags.
Signed-off-by: Valentin Longchamp <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.
So use IFC acessor functions instead of in_be32().
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
LIODN entry for B4860/B4420 mentions USB controller as "mph"
insread of "dr". This results in PAMU not permitting bus
transactions for USB DR controller on B4860 resulting in
USB function failure. Replacing "fsl-usb2-mph" with
"fsl-usb2-dr" allows USB DR controller bus transactions
Signed-off-by: Poonam Aggrwal <[email protected]>
Signed-off-by: Ramneek Mehresh <[email protected]>
Reviewed-by: Sethi Varun-B16395 <[email protected]>
Reviewed-by: Sun Yusong-R58495 <[email protected]>
|
|
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <[email protected]>
Signed-off-by: Roy Zang <[email protected]>
Acked-By: Joe Hershberger <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
|
|
Add initial support for TBS2910 Matrix ARM miniPC.
Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC.
Signed-off-by: Soeren Moch <[email protected]>
|
|
Signed-off-by: Nikolay Dimitrov <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
|
|
add SUPPORT_SPL feature for iMX6 SabreSD. It need to use
mx6sabresd_spl_defconfig to compile it.
Signed-off-by: John Tobias <[email protected]>
|
|
|
|
Add two missing Kconfig options for Novena and drop the SPL
from the Novena config.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Sean Cross <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
|
|
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Without this the cache will only work in write-through mode, and as soon as
it is put in write-back mode things break.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
Add full support for dram initialization, using a fixed clock and autodetection
of the memory organization (numbers of channels, bus-width, etc.).
This is based on dram_sun6i.c and dram.h from u-boot in the Allwinner A31 SDK,
extended with extra initialization sequences and the autodetect algorithm
from boot0.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
In preparation for adding sun6i dram support.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
Not used atm, for future use (e.g. PSCI).
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).
Also add some extra clock register constant defines.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.
Signed-off-by: Oliver Schinagl <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
|
|
Commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs)
collected the default values of CONFIG_SYS_CPU into arch/arm/Kconfig.
This commit moves "armv8" to there for consistency.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Georges Savoundararadj <[email protected]>
|
|
This commit adds "select CPU_V7" for some new boards that were not
covered by commit 2e07c249a67e
(kconfig: arm: introduce symbol for ARM CPUs).
Redundant "SYS_CPU" defines and "string" directives should be removed.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Acked-by: Georges Savoundararadj <[email protected]>
|
|
There is no board with CPU "arm_intcm".
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Albert Aribaud <[email protected]>
|
|
Precisely, these boards are SH4A rather than SH4.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Now each board selects one of CONFIG_CPU_SH2, CONFIG_CPU_SH3,
CONFIG_CPU_SH4, so let's move CONFIG_SYS_CPU definition to
arch/sh/Kconfig.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
This commit moves CONFIG_SH2, CONFIG_SH2A, CONFIG_SH3, CONFIG_SH4
to Kconfig renaming into CONFIG_CPU_SH2, CONFIG_CPU_SH2A,
CONFIG_CPU_SH3, CONFIG_CPU_SH4, respectively because
arch/sh/Kconfig of Linux uses CONFIG_CPU_SH* convention.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
The current prompts were added by a conversion tool
based on board directory names when switching to Kconfig.
Use better prompts mostly taken from from arch/sh/boards/*
of Linux Kernel.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <[email protected]>
Cc: Anatolij Gustschin <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: York Sun <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
The bmode command forces the SoC to use a specific boot device
by writing its boot mode into SRC_GPR9, and notifying the SoC of
the change using SRC_GPR10[28] bit: if the bit is on, bootROM
uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine
the boot device.
SPL on the other hand is oblivious to this distinction, so once
the bootROM loads SPL from the device configured in SRC_GPR10,
SPL will attempt to load U-Boot from the device configured in
SRC_SMBR1, which is not updated by the bootROM to the value in
SRC_GPR9.
The result is that the selected boot device is not used across all
the boot stages.
Update spl_boot_device() to look at gpr9 when necessary.
Signed-off-by: Nikita Kiryanov <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Troy Kisky <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Eric Nelson <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
size_t is the canonical type to represent variables that contain a size.
Use it instead of signed integer. Physical addresses can be larger than
32-bit, so use a more appropriate type for them as well. phys_addr_t is
a type that is 32-bit on systems that use 32-bit addresses and 64-bit if
the system is 64-bit or uses a form of physical address extension to use
a larger address space on 32-bit systems. Using these types the same API
can be implemented on a wider range of systems.
Signed-off-by: Thierry Reding <[email protected]>
|
|
Remove two gratuituous blank lines, uses u32 (instead of int) as the
type for values that will be written to a register, moves the beginning
of the variable declaration section to a separate line (rather than the
one with the opening brace) and keeps the function signature on a single
line where possible.
Signed-off-by: Thierry Reding <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
|
|
|
|
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
This reverts commit 1e96220a5687efae2aed45ce56e143336c40d0a7.
Remove duplicated vxworks.h header.
The same change was done by
"ARM: prevent compiler warnings from bootm.c"
(sha1: 8d196e52b58d1e50a80c2f5067b201cda521c75c)
Signed-off-by: Michal Simek <[email protected]>
|
|
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and
it is defined in ./.config but not in spl/.config,
so pin_init() should be called from the normal image
so that UART works correctly.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This commit merges
arch/arm/cpu/armv7/uniphier/ph1-*/board_postclk_init.c
to
arch/arm/cpu/armv7/uniphier/board_postclk_init.c
Because PH1-Pro4 does not have the BCU block, add __weak to
bcu_init().
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
The function sg_set_pinsel is useful for switching I/O pins
but it can be only used in C code. This commit adds a simple
macro that is available in asm code.
Signed-off-by: Masahiro Yamada <[email protected]>
|
