| Age | Commit message (Collapse) | Author |
|---|
|
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
This patch avoids compilation issue when CONFIG_USB_GADGET is deactivated
in defconfig, with undefined reference to run_usb_dnl_gadget and to
g_dnl_set_product.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mpc8xx
This pull request adds support for temperature sensors et FPGA loading
on boards from CS GROUP France.
CI: https://source.denx.de/u-boot/custodians/u-boot-mpc8xx/-/pipelines/20416
|
|
enabled""
As reported by Jonas Karlman this series breaks booting on some AArch64
platforms with common use cases. For now the best path forward is to
revert the series.
This reverts commit 777c28460947371ada40868dc994dfe8537d7115, reversing
changes made to ab3453e7b12daef47b9e91da2a2a3d48615dc6fc.
Link: https://lore.kernel.org/u-boot/[email protected]/
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
Unlike CMPC885 and CMPCPRO boards, the FPGA of MCR3000 board doesn't
load code automatically but needs to be loaded by software through SPI.
Until now it was loaded later by Linux, but we'd like U-boot to have
access to some information that require the FPGA, like board address
in racks.
So, implemented the load of FPGA in U-boot.
Signed-off-by: Christophe Leroy <[email protected]>
---
To avoid spamming your email boxes, the code isn't included in
the emailed patch but will be present in the PULL request
|
|
SDMA configuration register needs to be set up only once and doesn't
belong to drivers. Also, the value to be used is different on mpc885.
So do the init in cpu_init_f() with 0x40 for mpc885 and 0x1 for others.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
All CSSI boards have an LM74 chip as temperature sensor.
Enable it.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
MCR3000 board has some components tied to the SPI bus, like the Texas
Instruments LM74 temperature sensor.
Add support for SPI bus. The SPI chipselects are a bit special in the
way that they are driven by 3 bits in a register of the board's CPLD
where the value writen in those bits exclusively activates one of the
7 possible chipselects and value 0 sets all chipselets to inactive.
So add a special GPIO driver that simulates GPIOs for those chipselect.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
When adding additional SPI peripherals, the reg property needs to
be added, and this leads to the following error:
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@1:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@2:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Fix it by removing cell-index and cell-size which is unused and add
reg property. Also fix node name to be in line with reg value.
Also add missing compatible for eeprom node.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
Enable OF_UPSTREAM to use upstream DT and add renesas/ prefix to the
DEFAULT_DEVICE_TREE and OF_LIST. And thereby directly build DTB from
dts/upstream/src/ including *-u-boot.dtsi files from arch/$(ARCH)/dts/
directory.
The configuration update has been done using the following script:
```
sed -i '/^CONFIG_DEFAULT_DEVICE_TREE/ s@="@&renesas/@' `git grep -li renesas configs`
sed -i '/^CONFIG_OF_LIST/ s@r8a@renesas/&@g' `git grep -li renesas configs`
```
The RZN1 Snarc board does not seem to have a matching Linux kernel
DT counterpart, this is currently not switched to OF upstream.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
|
|
Enable OF_UPSTREAM to use upstream DT and add renesas/ prefix to the
DEFAULT_DEVICE_TREE and OF_LIST. And thereby directly build DTB from
dts/upstream/src/ including *-u-boot.dtsi files from arch/$(ARCH)/dts/
directory.
The configuration update has been done using the following script:
```
sed -i '/^CONFIG_DEFAULT_DEVICE_TREE/ s@="@&renesas/@' `git grep -li renesas configs`
sed -i '/^CONFIG_OF_LIST/ s@r8a@renesas/&@g' `git grep -li renesas configs`
```
There are SoCs which are not included in this patch. The 32bit SoCs
require further infrastructure work. R8A779H0 is coming during the
next upstream DT synchronization cycle as it is not included in
current upstream DTs yet.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Adam Ford <[email protected]> # Beacon boards
Reviewed-by: Paul Barker <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
|
|
R-Car R8A77950 H3 ES1.* was only available to an internal development
group and needed a lot of quirks and workarounds. Public users only
have R-Car R8A77950 H3 ES2 and newer. Switch existing systems to use
R8A77951 device trees.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The U-Boot build system can automatically paste -u-boot.dtsi at the
end of matching .dts during build. Stop emulating this behavior and
rename the -u-boot.dts files to -u-boot.dtsi, drop "#include...dts"
from those new u-boot.dtsi files, and update board configuration
accordingly.
The rename, '#include...dts` scrubbing and configuration update has
been done using the following script:
```
$ find . -name r[78]\*-u-boot.dts | sort -u | while read line ; do \
git mv ${line%-u-boot.dts}-u-boot.dts ${line%-u-boot.dts}-u-boot.dtsi ; \
done
$ sed -i '/^#include.*dts"/ d' `find . -name r[78]\*-u-boot.dtsi`
$ sed -i 's@-u-boot@@g' `git grep -li renesas configs`
```
The Salvator-X and ULCB board files have been updated manually.
Signed-off-by: Marek Vasut <[email protected]>
Acked-by: Adam Ford <[email protected]>
|
|
If open() fails it returns -1. Calling close() with this value
makes no sense. Return -EIO instead.
Addresses-Coverity-ID: 185828 Improper use of negative value
Signed-off-by: Heinrich Schuchardt <[email protected]>
Fixes: 566bf3a8698 ("sandbox: Add a function to read a host file")
Reviewed-by: Sean Anderson <[email protected]>
|
|
When we find a certificate on an image to be booted on a GP device we
print out a message explaining that the certificate is being skipped.
This message is rather long and is printed for every image. Shorten
the message and make the long version into a debug message.
Signed-off-by: Andrew Davis <[email protected]>
Tested-by: Jonathan Humphreys <[email protected]>
|
|
Add Kconfig that enables FPGA reprogramming with warm boot on Arria 10.
This option allows to change the bitstream on the filesystem and apply
changes with warm reboot without the need for a power cycle.
Signed-off-by: Michał Barnaś <[email protected]>
|
|
MD Danish Anwar <[email protected]> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
|
|
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <[email protected]>
Reviewed-by: Ravi Gunasekaran <[email protected]>
|
|
The function uniphier_mem_map_init() is to change global variable
'mem_map', which is referenced to get_page_table_size() to calculate
the size of page table.
However, uniphier_mem_map_init() is called after get_page_table_size(),
so the size of page table and 'mem_map' become inconsist each other.
After all, U-Boot fails to boot on chip with memory map different from
default map,
uniphier_mem_map_init() should be moved to dram_init(), which is
called before get_page_table_size().
Signed-off-by: Kunihiko Hayashi <[email protected]>
|
|
Mentions that command line option --signal is needed to make use of this
configuration option.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Instead of checking a configuration setting in booti_start() adjust the
sandbox implementation of booti_setup().
Write a console message when trying to run the booti command on the sandbox
indicating that it is not supported.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
We should check the return value of fcntl().
Addresses-Coverity-ID: 131108 ("Unchecked return value from library")
Addresses-Coverity-ID: 131109 ("Unchecked return value from library")
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Introduce get_boot_device() to obtain the booting device. Make it also
available for non SPL builds so u-boot can also know the device it is
booting from.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Relocate booindex to OCRAM region after it gets opened by TIFS so
the main domain bootloaders can have access to this data.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Add support for signing of TIFSSTUB images for HSSE, HSFS and GP devices
and include them in tispl.bin and tispl.bin_unsigned.
Signed-off-by: Kamlesh Gurudasani <[email protected]>
Signed-off-by: Dhruva Gole <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Add support for detecting and processing TIFSSTUB images for HS, HSFS
and GP devices.
TIFSSTUB image for related device type will be loaded, rest TIFSSTUB
images will be discarded.
Example, for GP device, tifsstub-gp will be loaded, tifsstub-hs and
tifsstub-fs will be discarded.
Signed-off-by: Kamlesh Gurudasani <[email protected]>
Signed-off-by: Dhruva Gole <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Move verdin-am62 to OF_UPSTREAM:
- handle the fact that dtbs now have a 'ti/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS file
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
|
|
This extra binding is non-standard and now unneeded as we bind the
sysreset driver automatically. This matches what is done in Linux
and allows us to more closely match the DTBs. Remove the binding
and all users.
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
Tested-by: Jonathan Humphreys <[email protected]>
|
|
During the boot, the EFI loader maps the memory from ram_top to ram_end
as EFI_BOOT_SERVICES_DATA. When LMB does boot_fdt_add_mem_rsv_regions()
to OPTEE, TFA, R5, and M4F DMA/memory "no-map" for the kernel it produces
the following error message:
ERROR: reserving fdt memory region failed (addr=9cb00000 size=100000 flags=4)
ERROR: reserving fdt memory region failed (addr=9cc00000 size=e00000 flags=4)
ERROR: reserving fdt memory region failed (addr=9da00000 size=100000 flags=4)
ERROR: reserving fdt memory region failed (addr=9db00000 size=c00000 flags=4)
ERROR: reserving fdt memory region failed (addr=9e780000 size=80000 flags=4)
ERROR: reserving fdt memory region failed (addr=9e800000 size=1800000 flags=4)
To avoid this, don't flag with EFI_BOOT_SERVICES_DATA the memory from
ram_top to ram_end by the EFI loader.
Signed-off-by: Vitor Soares <[email protected]>
|
|
The maximum frequency of the A53 CPU on the AM62 depends on the speed
grade of the SoC. However, this value is hardcoded in the DT for all
AM62 variants, potentially causing specifications to be exceeded. Moreover,
setting a common lower frequency for all variants increases boot time.
To prevent these issues, modify the DT at runtime from the R5 core to
adjust the A53 CPU frequency based on its speed grade.
Suggested-by: Vignesh Raghavendra <[email protected]>
Signed-off-by: Joao Paulo Goncalves <[email protected]>
|
|
AM62 SoC has multiple speed grades. Add function to return max A53 CPU
frequency based on grade. Fastest grade's max frequency also depends on
PMIC voltage, to simplify implementation use the smaller value.
Suggested-by: Vignesh Raghavendra <[email protected]>
Signed-off-by: Joao Paulo Goncalves <[email protected]>
|
|
Simon Glass <[email protected]> says:
This little series reprises the EFI-video fix, fixes a USB problem and
enables a boot script for coreboot.
It also moves to truetype fonts for coreboot and qemu-x86, since the
menus look much better and there are no strong size constraints.
With these changes it is possible to boot a Linux distro automatically
with U-Boot on x86, including when U-Boot is the second-stage
bootloader.
|
|
Truetype fonts look better in the menu, so enable them.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is needed to support Truetype fonts. In any case, the compiler
expects SSE to be available in 64-bit mode. Provide an option to enable
SSE so that hardware floating-point arithmetic works.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Suggested-by: Bin Meng <[email protected]>
|
|
Simon Glass <[email protected]> says:
This series is the culmanation of the current line of refactoring
series. It adjusts pxe to call the booting functionality directly
rather than going through the command-line interface.
With this is is possible to boot using the extlinux bootmeth without
the command line enabled.
It also updates fastboot to do a similar thing.
|
|
At this point most things work, including booting a distro, so drop
this message.
Signed-off-by: Simon Glass <[email protected]>
|
|
Allow these functions to be compiled in when CONFIG_BOOTM is enabled,
even if CONFIG_CMD_BOOTM is not.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Angelo Dureghello <[email protected]>
|
|
Simon Glass <[email protected]> says:
This series refactors the zboot code to allow it to be used with
CONFIG_COMMAND disabled.
A new zboot_run() function is used to boot a zimage.
|
|
Now that we have a function to start the process of booting a zimage,
use it in zboot_run() to avoid duplicated logic.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move zboot_start() and zboot_info() in with the other logic functions.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
The term 'start' is used withint bootm and zboot to indicate the first
phase of booting an image.
Since zboot_start() does the whole boot, rename it to zboot_run() to
align with bootm_run() etc.
Fix a log message while we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
The only difference between the command and the underlying logic is the
setting of envrionment variables. Move this out of the command
processing since it needs to be done in any case.
Signed-off-by: Simon Glass <[email protected]>
|
|
Most of the functionality of zboot is contained in the logic which
handles a zimage. Create a separate Kconfig for the logic so that it can
(later) be used without the command itself being enabled.
Enable ZBOOT by default on x86, with the command depending on that. The
existing 'imply' can therefore be removed.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Much of the code in zimage.c deals with the zboot command. Move it into
a sepatate zboot.c file within the cmd/ directory. This will eventually
allow use of the zimage logic without the command being enabled.
Signed-off-by: Simon Glass <[email protected]>
|
|
In preparation for splitting the zboot-command code into a separate
file, move the definitions into the header file.
While we are here, mention when load_address and base_ptr are set up
and explain bzimage_addr better. Make cmdline const since it cannot be
changed.
Signed-off-by: Simon Glass <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.07-rc1
xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding
zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant
zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update
mbv:
- Enable SPL and binman
- Small platform changes
zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path
versal-net:
- Support multiple locations for variables
|
|
The implementation of map_range() creates the requested mapping by
walking the page tables, iterating over multiple PTEs and/or descending
into existing table mappings as needed. When doing so, it assumes any
pre-existing valid PTE to be a table mapping. This assumption is wrong
if the platform code attempts to successively map two overlapping ranges
where the latter intersects a block mapping created for the former.
As a result, map_range() treats the existing block mapping as a table
mapping and descends into it i.e. starts interpreting the
previously-mapped range as an array of PTEs, writing to them and
potentially even descending further (extra fun with MMIO ranges!).
Instead, pass any valid non-table mapping to split_block(), which
ensures that it actually was a block mapping (calls panic() otherwise)
before splitting it.
Fixes: 41e2787f5ec4 ("arm64: Reduce add_map() complexity")
Signed-off-by: Pierre-Clément Tosi <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
Tested-by: Hiago De Franco <[email protected]> # Toradex Verdin AM62
Reviewed-by: Marc Zyngier <[email protected]>
|
|
Export a function get_product_id_from_eeprom() to read the product ID.
This value can be used for fixing up the device-tree on JH7110 based
products.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
