| Age | Commit message (Collapse) | Author |
|---|
|
Some later 32-bit SoCs require some setup of the Secure Peripherals
Controller, which is handled in tzpc_init().
At the moment this is guarded in board.c by some #ifdefs selecting the
SoCs that need it.
Move those #ifdef guards into the header file, providing an empty stub
function for all other SoCs, so that the #ifdefs can be removed from the
.c file, to improve readability.
Signed-off-by: Andre Przywara <[email protected]>
|
|
R528/T113 SoCs uses the same SPI IP as the H6, also have the same clocks
and reset bits layout, but the CCU base is different. Another difference
is that the new SoCs do not have a clock divider inside. Instead of this
we should configure sample mode depending on input clock rate.
The pin assignment is also different: the H6 uses PC0, the R528/T113 PC4
instead. This makes for a change in spi0_pinmux_setup() routine.
This patch extends the H6/H616 #ifdef guards to also cover the R528/T113,
using the shared CONFIG_SUNXI_GEN_NCAT2 and CONFIG_MACH_SUN8I_R528
symbols. Also use CONFIG_SUNXI_GEN_NCAT2 symbol for the Kconfig
dependency.
Signed-off-by: Maksim Kiselev <[email protected]>
Tested-by: Sam Edwards <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-video
CI: https://source.denx.de/u-boot/custodians/u-boot-video/-/pipelines/20466
- simple_panel: support timing parsing from EDID
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
|
|
Existing Tegra DSI driver mostly fits T114 apart MIPI calibration
which on T114 has dedicated driver. To resolve this MIPI calibration
logic was split for pre-T114 and T114+ devices.
Tested-by: Ion Agorria <[email protected]> # HTC One X
Tested-by: Svyatoslav Ryhel <[email protected]> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <[email protected]>
Reviewed-by: Thierry Reding <[email protected]>
|
|
Based on Thierry Reding's Linux commit:
'commit 1716b1891e1de05e2c20ccafa9f58550f3539717
("drm/tegra: rgb: Parameterize V- and H-sync polarities")'
Signed-off-by: Svyatoslav Ryhel <[email protected]>
Reviewed-by: Thierry Reding <[email protected]>
|
|
Consolidate HD headers and place the result into video/tegra20
since it is used only by devices from this directory.
Tested-by: Agneli <[email protected]> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <[email protected]> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <[email protected]> # ASUS Grouper E1565
Tested-by: Ion Agorria <[email protected]> # HTC One X
Tested-by: Svyatoslav Ryhel <[email protected]> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <[email protected]>
Reviewed-by: Thierry Reding <[email protected]>
|
|
Diverge DC driver setup to better fit each of supported generations
of Tegra SOC.
Tested-by: Agneli <[email protected]> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <[email protected]> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <[email protected]> # ASUS Grouper E1565
Tested-by: Ion Agorria <[email protected]> # HTC One X
Tested-by: Svyatoslav Ryhel <[email protected]> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Enable and set the start address of pre-console buffer for RK3328.
Signed-off-by: Jagan Teki <[email protected]>
|
|
Model: Firefly roc-rk3328-cc
DRAM: 1 GiB (effective 1022 MiB)
Video device 'vop@ff370000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'rockchip_rk3328_vop': -28
Some drivers failed to bind
initcall sequence 000000003ffcd5e8 failed at call 000000000021a5c4 (err=-28)
### ERROR ### Please RESET the board ###
Signed-off-by: Jagan Teki <[email protected]>
|
|
VOP get and set clock would needed for VOP drivers.
Add support for it.
Signed-off-by: Jagan Teki <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI:
https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20444
- Make i.MX93 boot less verbose.
- Remove unneedd environment variables from Toradex i.MX boards.
- Use gpio-hog on verdin-imx8mm/imx8mp.
- Add PCIe support for i.MX8MM.
- Add TPM support for imx8m*-venice.
|
|
On qemu-x86_64_defconfig the following was observed:
=> efidebug tables
00000000000f0074 eb9d2d31-2d88-11d3-9a16-0090273fc14d SMBIOS table
The SMBIOS configuration table does not point to a paragraph-aligned
(16 byte aligned) address. The reason is that in write_tables() rom_addr is
not aligned and copied to gd->arch.smbios_start.
The Simple Firmware Interface requires that the SFI table is paragraph-
aligned but our code does not guarantee this.
As all tables written in write_tables() must be paragraph-aligned, we
should implement the address rounding in write_tables() and not in table
specific routines like copy_pirq_routing_table().
Add paragraph-alignment in write_tables().
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In Linux, we allow sleep moci to be turned off when the carrier board
supports it and the system is in suspend. In U-Boot, however, we want
the sleep moci to be always on. So we use a gpio hog and disable the
regulator. This change is necessary because we switched to upstream
device tree files with commit 23fe2def1edf
("verdin-imx8mm/verdin-imx8mp: move imx verdins to OF_UPSTREAM"). A
recent upstream patch removes the gpio hog from the Linux device tree,
so we need to add it to the u-boot dtsi. The following patch will remove
the gpio hog from the Linux device tree:
https://lore.kernel.org/linux-devicetree/[email protected]/
The U-Boot patch can be applied without it and will not break the build.
Signed-off-by: Stefan Eichenberger <[email protected]>
|
|
The blue led is used to indicate U-Boot entering / exit indication
then Linux heartbeat.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds"; which is not present in kernel DT.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ button-user-2 for fastboot mode activation.
Remove proprietary st,fastboot-gpios and st,stm32prog-gpios.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
The blue led is used to indicate U-Boot entering / exit indication
then Linux heartbeat.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds" which is not present in kernel DT.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ button-user-2 for fastboot mode activation.
Remove proprietary st,fastboot-gpios and st,stm32prog-gpios.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename "red" led node's name to "led-red".
Remove status property which is useless.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Remove "color" property from led-red node which is not supported
by U-Boot.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
led-red and button dedicated to fastboot share the same gpio GPIOA13.
led-blue and button dedicated to stm32prog share the same gpio GPIOA14.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from led-red and
led-blue led's node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Add 2 gpio-keys :
_ button-user-1 for stm32prog mode activation.
_ update button-user's label (defined in kernel DT) to match label
requested in board_key_check() for fastboot mode activation.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a58c ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a58c ("arm: dts: stm32: Add partitions in flash0 and nand node for
stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Fix flash@0 and nand@0 partition node name with correct offset.
Fixes: e91d3c61767b ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-ev1")
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
In case of an OTP-CLOSED STM32MP15xx system, the CPU core 1 cannot be
released from endless loop in BootROM only by populating TAMP BKPxR 4
and 5 with magic and branch address and sending SGI0 interrupt from
core 0 to core 1 twice. TAMP_SMCR BKP..PROT fields must be initialized
as well to release the core 1 from endless loop during the second SGI0
handling on core 1. Initialize TAMP_SMCR to protect the first 32 backup
registers, the ones which contain the core 1 magic, branch address and
boot information.
This requirement seems to be undocumented, therefore it was necessary
to trace and analyze the STM32MP15xx BootROM using OpenOCD and objdump.
Ultimately, it turns out that a certain BootROM function reads out the
TAMP_SMCR register and tests whether the BKP..PROT fields are non-zero.
If they are zero, the BootROM code again waits for SGI0 using WFI, else
the execution moves forward until it reaches handoff to the TAMP BKPxR 5
branch address.
This fixes CPU core 1 release using U-Boot PSCI implementation on an
OTP-CLOSED system, i.e. system with fuse 0 bit 6 set.
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
SoC revision is only accessible via DBUMCU IDC register,
which requires BSEC.DENABLE DBGSWENABLE bit to be set to
make the register accessible, otherwise an access to the
register triggers bus fault. As BSEC.DBGSWENABLE is zero
in case of an OTP-CLOSED system, do NOT set DBGSWENABLE
bit as this might open a brief window for timing attacks.
Instead, report that this system is OTP-CLOSED and do not
report any SoC revision to avoid confusing users. Use an
SEC/C abbreviation to avoid growing SOC_NAME_SIZE .
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
This patch avoids compilation issue when CONFIG_USB_GADGET is deactivated
in defconfig, with undefined reference to run_usb_dnl_gadget and to
g_dnl_set_product.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mpc8xx
This pull request adds support for temperature sensors et FPGA loading
on boards from CS GROUP France.
CI: https://source.denx.de/u-boot/custodians/u-boot-mpc8xx/-/pipelines/20416
|
|
enabled""
As reported by Jonas Karlman this series breaks booting on some AArch64
platforms with common use cases. For now the best path forward is to
revert the series.
This reverts commit 777c28460947371ada40868dc994dfe8537d7115, reversing
changes made to ab3453e7b12daef47b9e91da2a2a3d48615dc6fc.
Link: https://lore.kernel.org/u-boot/[email protected]/
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
Unlike CMPC885 and CMPCPRO boards, the FPGA of MCR3000 board doesn't
load code automatically but needs to be loaded by software through SPI.
Until now it was loaded later by Linux, but we'd like U-boot to have
access to some information that require the FPGA, like board address
in racks.
So, implemented the load of FPGA in U-boot.
Signed-off-by: Christophe Leroy <[email protected]>
---
To avoid spamming your email boxes, the code isn't included in
the emailed patch but will be present in the PULL request
|
|
SDMA configuration register needs to be set up only once and doesn't
belong to drivers. Also, the value to be used is different on mpc885.
So do the init in cpu_init_f() with 0x40 for mpc885 and 0x1 for others.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
All CSSI boards have an LM74 chip as temperature sensor.
Enable it.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
MCR3000 board has some components tied to the SPI bus, like the Texas
Instruments LM74 temperature sensor.
Add support for SPI bus. The SPI chipselects are a bit special in the
way that they are driven by 3 bits in a register of the board's CPLD
where the value writen in those bits exclusively activates one of the
7 possible chipselects and value 0 sets all chipselets to inactive.
So add a special GPIO driver that simulates GPIOs for those chipselect.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
When adding additional SPI peripherals, the reg property needs to
be added, and this leads to the following error:
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@1:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
arch/powerpc/dts/cmpc885.dtb: Warning (reg_format): /immr@ff000000/spi@aa0/temp@2:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Fix it by removing cell-index and cell-size which is unused and add
reg property. Also fix node name to be in line with reg value.
Also add missing compatible for eeprom node.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
Enable OF_UPSTREAM to use upstream DT and add renesas/ prefix to the
DEFAULT_DEVICE_TREE and OF_LIST. And thereby directly build DTB from
dts/upstream/src/ including *-u-boot.dtsi files from arch/$(ARCH)/dts/
directory.
The configuration update has been done using the following script:
```
sed -i '/^CONFIG_DEFAULT_DEVICE_TREE/ s@="@&renesas/@' `git grep -li renesas configs`
sed -i '/^CONFIG_OF_LIST/ s@r8a@renesas/&@g' `git grep -li renesas configs`
```
The RZN1 Snarc board does not seem to have a matching Linux kernel
DT counterpart, this is currently not switched to OF upstream.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
|
|
Enable OF_UPSTREAM to use upstream DT and add renesas/ prefix to the
DEFAULT_DEVICE_TREE and OF_LIST. And thereby directly build DTB from
dts/upstream/src/ including *-u-boot.dtsi files from arch/$(ARCH)/dts/
directory.
The configuration update has been done using the following script:
```
sed -i '/^CONFIG_DEFAULT_DEVICE_TREE/ s@="@&renesas/@' `git grep -li renesas configs`
sed -i '/^CONFIG_OF_LIST/ s@r8a@renesas/&@g' `git grep -li renesas configs`
```
There are SoCs which are not included in this patch. The 32bit SoCs
require further infrastructure work. R8A779H0 is coming during the
next upstream DT synchronization cycle as it is not included in
current upstream DTs yet.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Adam Ford <[email protected]> # Beacon boards
Reviewed-by: Paul Barker <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
|
