| Age | Commit message (Collapse) | Author |
|---|
|
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <[email protected]>
Tested-by: Mikhail Kalashnikov <[email protected]>
Tested-by: Bob McChesney <[email protected]>
Tested-by: Stephen Graf <[email protected]>
|
|
The current emac setting is not suitable for Orange Pi Zero 3,
move it back to Orange Pi Zero 2 DT. Also update phy mode and
delay values for emac on Orange Pi Zero 3.
With these changes, Ethernet now looks stable.
Fixes: 95c3b0635ea4 ("sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6")
Signed-off-by: Chukun Pan <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
|
|
Using /bits/ 64 prefix for 64 bits address
Signed-off-by: Randolph <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
On 32-core platform, hart31 gets stuck at secondary_hart_loop
as the corresponding enable bit is not set in enable_ipi().
We should program the next word (0x2f84) which is assigned
as the enable register of hart31. It should be done in the same
way when we invoke riscv_send_ipi() to trigger software interrupt
on hart31.
The following diagram shows the enable bits of the fixed PLICSW
scheme.
Pending regs: 0x1000 x---0---0---0---0------0---0
Pending hart ID: 0 1 2 3 ... 30 31
Interrupt ID: 0 1 2 3 4 ... 31 32
| | | | | | |
Enable regs: 0x2000 x---1---0---0---0-...--0---0---> hart0
| | | | | | |
0x2080 x---0---1---0---0-...--0---0---> hart1
| | | | | | |
0x2100 x---0---0---1---0-...--0---0---> hart2
| | | | | | |
0x2180 x---0---0---0---1-...--0---0---> hart3
. . . . . . .
. . . . . . .
. . . . . . .
0x2f00 x---0---0---0---0-...--1---0---> hart30
| | | | | | |
0x2f80 x---0---0---0---0-...--0---1---> hart31
<-------- word 0 -------><--- word 1 --->
This patch includes some cleanups to macros/functions.
Fixes: ebf11273220a ("riscv: andes: Rearrange Andes PLICSW to single-bit-per-hart strategy")
Signed-off-by: Yu Chien Peter Lin <[email protected]>
Reviewed-by: Randolph <[email protected]>
|
|
Adds jh7110 watchdog device tree node.
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Prepare v2024.01-rc4
# -----BEGIN PGP SIGNATURE-----
#
# iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmVuHrwACgkQFHw5/5Y0
# tyy3Tgv+LB/X0ZR3IHnu1mvQ7kpOFvAjjKr0BUpcEEzsrDZeJnS6sy06m+REez2E
# UmuLeKFj5NUCYXNKtxn2+gVnJt8Tk6ftxhMTiZHmR4Y4NVc5aPtqYmVsv6Q29j0U
# mcg7AGcZTniu9/naNM+ZcDeHzLDAB0whmE9eVfixXVgyitILoLHNdFiQ7W4oR7Kh
# /mBgdMDBS3rqiRi6CuqKUnl4ADX8T3AXaSfi3hqOC5Pj+HPkZSUfyWx31mu9mN1D
# wXTHASZX06Dop25fm/ZSdWk1blBw29WqRiJBdwNatvyC5pqMsotTvAfH2AcHBEYg
# tpoper+WDOBAipt6b6Y1B7q4VPvJ97L9dFCAYqN0nGCe+rkdi+k+cly7M6Ye9xLt
# e7rVUfnKgIMP8jkLcVBYoWkFY5FiJ82O5qjoF5N3dAuHeWacDFsB5TugDTOQvblH
# LWCmcIyU1N9Ma/Ib0rTvNduvpBUYBKXYlD1+rjPZUbTUnfc79mf+ReFpcoW6Kxh+
# bkz81p8P
# =ebIZ
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 04 Dec 2023 01:47:24 PM EST
# gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <[email protected]>" [ultimate]
|
|
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Cong Dang <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
|
|
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-tegra into next
Device tree improvents for Paz00 and DM PMIC convertion of recently
merged Tegra boards.
|
|
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
|
|
Add defines for {in,out}s{b,w,l}() functions to make asm-generic/io.h
aware of them.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Add defines for __raw_{read,write}{b,w,l}() functions to make
make asm-generic/io.h aware of them.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Add defines for {in,out}s{b,w,l} functions to make asm-generic/io.h
aware of them.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Change type of address parameter from int* to volatile void* for
{read,write}s{b,w,l}() functions and add const qualifier for reads. This
is done to keep function signatures in sync with asm-generic/io.h and
other platforms.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Add defines for {read,write}s{b,w,l} functions to make asm-generic/io.h
aware of them.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Add defines for {read,write}{b,w,l,q}(), {read,write}s{b,w,l,q}() and
{in,out}s{b,w,l,q}() functions to make asm-generic/io.h aware of them.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Currently reads{b,w,l}() functions don't have const qualifier for their
address parameter. Since asm-generic/io.h in Linux has const for all
read functions, add it here as well to keep signatures in sync.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Add defines for {in,out}s{b,w,l}() functions to make sure that
they will be used by asm-generic/io.h
Signed-off-by: Igor Prusov <[email protected]>
|
|
Generic version of io.h should be included at the end of
architecture-specific ones to make sure that arch implementations are
used and to avoid redefinitions.
Signed-off-by: Igor Prusov <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
To quote the author:
The show_board_info() function was adjusted to weak so that it could be
entirely replaced with a board-specific implementation.
The intended way for boards to provide their own information is via a
sysinfo driver. But currently there is no way to show anything other
than the model name.
This series adds support for showing a few more items, in a way that is
easy for boards to extend.
Since there is already a weak checkboard() function, we don't need to
have two levels of weak function here. So this series drops the weak
attribute from show_board_info()
Existing boards will see a slight change in output, in that the model
name will appear first, before any custom output. If that is a problem,
then the solution is to implement a sysinfo driver for the board.
|
|
Create a sysinfo driver to avoid needing a custom checkboard()
function. With this the following information is printed when booting
from coreboot under QEMU:
Model: Standard PC (i440FX + PIIX, 1996)
Manufacturer: QEMU
Prior-stage version: 4.21-885-g2a87ef1eca56
Prior-stage date: 11/11/2023
Signed-off-by: Simon Glass <[email protected]>
|
|
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
|
|
|
|
Enable USB PHY nodes on ASUS Transformers, Grouper, Enadevoru
and LG X3. This is not mandatory since driver will use default
values but preferable for new devices.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Call regulators_enable_boot_on on board init to set all regulators
with boot-on property in device tree. If regulator is not used by
any device in the device tree but is essential for the device to
work a regression will occur.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Instead of duplicating the I2C3 node and adding NVEC specific
properties, reuse the I2C3 node, extend it with NVEC specific properties
and drop properties that are not needed by NVEC. This results in a DTB
that is a bit cleaner and avoids accidentally using I2C3 and NVEC which
would have them fight over the same hardware resources.
Signed-off-by: Thierry Reding <[email protected]>
|
|
Modify spi and usb aliases name.
Add dt-binding for usb phy define and fix usb phy reset error.
Add tpm/otpee and host_intf node.
Signed-off-by: Jim Liu <[email protected]>
|
|
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <[email protected]>
|
|
Sync devicetree with kernel v6.7-rc1
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
Sync devicetree with kernel v6.7-rc1
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
Reduce redundancy in code by using templates to generate the A72 boot
binaries (tispl.bin and u-boot.img) as well as R5 boot binary sysfw.itb
(for legacy boot following devices J721E and AM65x).
Signed-off-by: Neha Malcom Francis <[email protected]>
Acked-by: Andrew Davis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Manorit Chawdhry <[email protected]>
|
|
Add templates for FIT images used extensively across K3 boards with most
of the code common. This includes the FIT portions of:
- tispl.bin
- u-boot.img
- sysfw.itb (in case of legacy boot flow)
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
While at this enable the DM and TIFS UARTs for programming pinmux
since they are marked reserved by board.dts
Reviewed-by: Dhruva Gole <[email protected]>
Tested-by: Dhruva Gole <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
Reviewed-by: Dhruva Gole <[email protected]>
Tested-by: Dhruva Gole <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Change spl_enable_dcache so it also enable icache on SPL
initialization for the main domain part of the boot flow. This
improves bootloader booting time.
Link: https://lore.kernel.org/all/[email protected]/
Signed-off-by: Joao Paulo Goncalves <[email protected]>
Tested-by: Nishanth Menon <[email protected]>
|
|
k3-am62* SoC dtsi files now provide the following:
bootph-all: dmss secure_proxy_main dmsc k3_pds k3_clks k3_reset
main_pmx0 main_timer0 mcu_pmx0 wkup_conf chipid
bootph-pre-ram: secure_proxy_sa3 main_esm mcu_esm
Drop these from board r5 and u-boot.dtsi files as these are duplicate in
them now.
Acked-by: Francesco Dolcini <[email protected]>
Tested-by: Dhruva Gole <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Sync with kernel v6.7-rc1 and sync up the u-boot dts files accordingly.
Tested-by: Dhruva Gole <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
|
BCDMA can be used at SPL for OSPI boot and mem-to-mem DMA
so add "bootph-all" to BCDMA node.
Suggested-by: Nishanth Menon <[email protected]>
Fixes: 9a3f2b6798b0 ("arm: dts: k3-am625-verdin-wifi-dev-u-boot.dtsi: Fix DMA/Ethernet")
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]>
|
|
Sync u-boot device tree with Linux kernel 6.7-rc1
Signed-off-by: Reid Tonking <[email protected]>
|
|
Sync with kernel v6.7-rc1 and sync up the u-boot dts files accordingly.
Signed-off-by: Nishanth Menon <[email protected]>
|
|
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Sync the U-Boot DTS files with those of Kernel v6.7-rc1.
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Add base support for BeagleBone AI-64 board support.
Further information at https://beagleboard.org/ai-64
Signed-off-by: Nishanth Menon <[email protected]>
|
|
BeagleBoard.org BeagleBone AI-64 is an open source hardware single
board computer based on the Texas Instruments TDA4VM SoC featuring
dual-core 2.0GHz Arm Cortex-A72 processor, C7x+MMA and 2 C66x
floating-point VLIW DSPs, 3x dual ARM Cortex-R5 co-processors,
2x 6-core Programmable Real-Time Unit and Industrial Communication
SubSystem, PowerVR Rogue 8XE GE8430 3D GPU. The board features 4GB
DDR4, USB3.0 Type-C, 2x USB SS Type-A, miniDisplayPort, 2x 4-lane
CSI, DSI, 16GB eMMC flash, 1G Ethernet, M.2 E-key for WiFi/BT, and
BeagleBone expansion headers.
This board family can be indentified by the BBONEAI-64-B0 in the
at24 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 42 4f 4e 45 41 |.U3..7....BBONEA|]
[49 2d 36 34 2d 42 30 2d 00 00 42 30 30 30 37 38 |I-64-B0-..B00078|]
Baseline of the devicetree is from v6.6-rc1
https://beagleboard.org/ai-64
https://git.beagleboard.org/beagleboard/beaglebone-ai-64
Signed-off-by: Robert Nelson <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Move the omap3 beagle to the beagle vendor folder representing
BeagleBoard.org platforms.
Suggested-by: Tom Rini <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
