| Age | Commit message (Collapse) | Author |
|---|
|
Add R8A779A0 V3U DT extras for U-Boot.
Based on "ARM: dts: renesas: Add R8A779A0 V3U DTs"
by Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Import R8A779A0 V3U Falcon DTs from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") .
Signed-off-by: Marek Vasut <[email protected]>
|
|
Import R8A779A0 V3U DTs and headers from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") .
Signed-off-by: Marek Vasut <[email protected]>
|
|
- x86: Discard .note.gnu.property sections
- nvme: Skip block device creation for inactive namespaces
- nvme: Convert NVMe doc to reST, and various minor fixes
|
|
All symbols that are defined in Kconfig will always be defined (or not)
prior to preprocessing due to the -include directive while building.
However, symbols which are not yet migrated will only be defined (or
not) once the board config.h is included, via <config.h>. While the end
goal must be to migrate all symbols, today we have cases where the size
of gd will get mismatched within the build, based on include order.
Mitigate this by making sure that any <asm/global_data.h> that uses
symbols not in Kconfig does start with <config.h>. Remove this when not
needed.
Cc: Alexey Brodkin <[email protected]>
Cc: Eugeniy Paltsev <[email protected]>
Cc: Huan Wang <[email protected]>
Cc: Angelo Dureghello <[email protected]>
Cc: Rick Chen <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
With the changes in commit 588efcdd72fc ("powerpc: Don't use relative
include for config.h in global_data.h") fixing the root of the problem,
we no longer need this re-inclusion.
This reverts commit f6c0d365d3e8ee8e4fd3ebe2ed957c2bca9d3328.
Cc: Matt Merhar <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
As there is an arch/powerpc/include/asm/config.h file using "" to get
config.h here can lead to using that rather than include/config.h. This
in turn can lead to a mismatch in the size of gd.
Cc: Matt Merhar <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Tested-by: Matt Merhar <[email protected]>
|
|
When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom
built from qemu-x86_defconfig no longer boots anymore. Investigation
shows that U-Boot fails at a very early stage during the boot process,
in fdtdec_prepare_fdt() where fdt_check_header() complains that there
is not a valid device tree found at gd->fdt_blob which points to _end.
Now _end points to an allocated section .note.gnu.property which of
course is wrong.
This issue is however not seen when using the default Ubuntu 20.04 gnu
toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows
that it is caused by a behavior change of binutils v2.36 which is part
of the kernel.org gcc 11.1.0 toolchain, via the following commit:
939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default")
In fact, there was already a regression bug report [1] for binutils two
months ago, but the binutils folks did not think it is a bug :(
To resolve this, there are several options:
* pass -Wa,-mx86-used-note=no to gas
* pass -R .note.gnu.property to objcopy
* discard the section in the linker script
Linux kernel uses the discard way [2], so let's do the same for U-Boot.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753
[2] commit 4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO")
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
DT files have been added this year but forgot to update it that's why do it
in separate patch now.
Signed-off-by: Michal Simek <[email protected]>
|
|
Wire psgtr for zc1751 dc1 board.
Signed-off-by: Michal Simek <[email protected]>
|
|
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.
Signed-off-by: Michal Simek <[email protected]>
|
|
Both boards are usb3.0 capable. dc3 was also missing enabling dwc3* nodes.
Signed-off-by: Michal Simek <[email protected]>
|
|
Align USB nodes with the latest dt-bindings. It is adding resets, new
interrupt and also some quirks.
Signed-off-by: Michal Simek <[email protected]>
|
|
dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.
Signed-off-by: Michal Simek <[email protected]>
|
|
kv260-revB is different compare to revA (usbhub is wired via i2c) that's
why remove revA compatible string.
Signed-off-by: Michal Simek <[email protected]>
|
|
Xilinx ZynqMP supports also addresses above 4GB (32bit) that's why also
generate u-boot.its with 64bit load/entry addresses to also support
different configurations.
Signed-off-by: Michal Simek <[email protected]>
|
|
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <[email protected]>
|
|
Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.
Signed-off-by: Michal Simek <[email protected]>
|
|
Linux kernel is not using these properties that's why they can be removed.
Signed-off-by: Michal Simek <[email protected]>
|
|
Networking subsystem is not using aliases that's why remove them for CAN
devices. There is also no any other Xilinx ZynqMP DT file with them.
Signed-off-by: Michal Simek <[email protected]>
|
|
There are no drivers for these devices that's why remove that nodes
completely. This change is done based on Linux kernel.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Convert all boards to use nvmem alias instead of xlnx,eeprom. The change is
done based on discussion in the link below.
Link: https://lore.kernel.org/r/CAL_JsqLMDqpkyg-Q7mUfw-XH67-v068Q6e9wTq2UOoN=0-_coQ@mail.gmail.com
Signed-off-by: Michal Simek <[email protected]>
|
|
As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
Oscillator Ticks that are required to measure the largest time
period that is less than or equal to 1 second.
For an oscillator that is 32.768 KHz, this value will be 0x7FFF."
Signed-off-by: Srinivas Neeli <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <[email protected]>
|
|
Historically dpdma and dpsub are placed at the end of files. Move nodes
there for easier comparison among dts files.
Signed-off-by: Michal Simek <[email protected]>
|
|
dp_aclk is not used anywhere that's why remove it.
Signed-off-by: Michal Simek <[email protected]>
|
|
Trivial patch.
Signed-off-by: Michal Simek <[email protected]>
|
|
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.
Signed-off-by: Michal Simek <[email protected]>
|
|
Remove unused phy.h from zc1232 DTS.
Signed-off-by: Michal Simek <[email protected]>
|
|
Uarts already have u-boot,dm-pre-reloc via zynqmp.dtsi that's why there is
no need to have them in platform DT files too.
Signed-off-by: Michal Simek <[email protected]>
|
|
There is need to pass entry about secure OS when bl32_entry is defined.
Currently only 64bit support is added but /fit-images node have been
extended to also record if this is 32bit or 64bit secure OS. When this is
tested the code will be update to support this configuration too.
Signed-off-by: Michal Simek <[email protected]>
|
|
The first change is to trying to find out TF-A load address based on
reading elf file. Expectation is that bl31.bin is in the same folder as
bl31.elf. It brings new flexibility to place TF-A to any address (DDR
included).
And also enable TEE generation also with TEE configuration.
Expecation is the same as above that tee.bin and tee.elf are in the same
folder.
User has to just define link to BL31/BL32 binary files and the rest should
be handled by the script.
Signed-off-by: Michal Simek <[email protected]>
|
|
Trivial change for all files I have touched recently.
Signed-off-by: Michal Simek <[email protected]>
|
|
Add label which is used by bootloader for adding bootloader specific flag.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/3dc8416abdd3498e61edcd83830a12af295c5c6d.1611224800.git.michal.simek@xilinx.com
|
|
Just sync it with others for easier comparison.
Signed-off-by: Michal Simek <[email protected]>
|
|
Sata needs to get reset before configuration that's why add property for it
there.
Signed-off-by: Michal Simek <[email protected]>
|
|
The SMMU is disabled in device tree so this change has no impact.
The benefit is that this way it is in sync with xen.dtsi. Xen enables
the SMMU and makes use of it.
Signed-off-by: Stefano Stabellini <[email protected]>
|
|
There is no reason to have CCI no enabled by default. Enable it when your
system configuration requires it. In Xilinx configuration flow this is
work for Device Tree Generator which reads information from HW Design
configuration.
Signed-off-by: Michal Simek <[email protected]>
|
|
Update the psgtr clock indexing for couple of zynqmp boards.
Signed-off-by: Michal Simek <[email protected]>
|
|
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI
point-to-point channels for communicating addresses, data, and response
transactions between master and slave clients. This ARM AMBA 3.0..."
Issues are reported as:
.. amba: $nodename:0: 'amba' does not match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
>From schema:
../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml
Similar change has been done for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
|
|
Enable gpio driver on these boards. GPIOs can be used on any board.
Signed-off-by: Michal Simek <[email protected]>
|
|
From U-Boot, loading application on RPU core 0 is fine but loading on
core 1 is not handled properly. Lock-step mode needs both the R5 cores
to be initialized and it is working fine. Whereas in SPLIT mode individual
R5 cores needs to be initialized as they need to execute differenet
applications. Handle both these lock-step and split modes by propagating
mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions
and by adding conditions in those functions.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to
json-schema") converted binding to yaml and some missing required
properties started to be reported. Align binding based on it.
The patch is fixing these warnings:
.../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property
>From schema: .../Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
|
|
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding
document to yaml") converted binding to yaml and 3 deprecated properties
pop up.
The patch is fixing these warnings:
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property
>From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml
by converting them to new binding.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
|
|
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid
spurious ECC errors that can occur when accessing unitialized memory.
The feature is enabled by setting the option
CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data:
SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex)
SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex)
Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action.
Signed-off-by: Jorge Ramirez-Ortiz <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Fix following dtc warning by explicitly setting up #size-cells
and #address-cells when overriding node in -u-boot.dtsi
arch/arm/dts/k3-j7200-common-proc-board.dtb: Warning (reg_format):
/bus@100000/bus@28380000/mcu-navss/ringacc@2b800000:reg: property has
invalid length (80 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Remove the LED unit addresses and reg properties to
fix the following dtc build warnings:
arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
...
arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value
Reported-by: Tom Rini <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Oleh Kravchenko <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip into next
- New SoC platform support: rk3568;
- rockchip pcie Code compile issue fix;
- Board fix for rk3399 Khadas Edge;
- Add Rockchip NFC driver;
|
|
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from
the linux tree:
$ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l
0
$ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l
633
In u-boot device trees both prefixes are used. Until recently the only
user of the ethernet alias was the sandbox test device tree. This
changed with commit fc054d563bfb ("net: Introduce DSA class for Ethernet
switches"). There, the MAC addresses are inherited based on the devices
sequence IDs which is in turn given by the device tree.
Before there are more users in u-boot and both worlds will differ even
more, rename the alias prefix to "ethernet" to match the linux ones.
Also adapt the test cases and rename any old aliases in the u-boot
device trees.
Cc: David Wu <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Handle DFU stack error in STM32CubeProgrammer protocol.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
