| Age | Commit message (Collapse) | Author |
|---|
|
Mark the top of ram, used for relocated U-Boot as a normal memory
(cacheable and executable) to avoid permission access issue when
U-Boot jumps to this relocated code.
When MMU is activated in pre-reloc stage; only the beginning of
DDR is marked executable.
This patch avoids access issue when DACR is correctly managed.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This reverts commit 576007aec9a4a5f4f3dd1f690fb26a8c05ceb75f.
The parameter passed to reset_cpu() no longer holds a meaning as all
call-sites now pass the value 0. Thus, branching on it is essentially
dead code and will just confuse future readers.
Revert soft-reset support and just always perform a hard-reset for now.
This is a preparation for removal of the reset_cpu() parameter across
the entire tree in a later patch.
Fixes: 576007aec9a4 ("lpc32xx: cpu: add support for soft reset")
Cc: Sylvain Lemieux <[email protected]>
Signed-off-by: Harald Seiler <[email protected]>
|
|
nds32 is one of the only architectures which still have a reset_cpu()
implementation that makes use of the `addr` parameter. The rest of
U-Boot now ignores it and passes 0 everywhere. It turns out that even
here, reset_cpu() is no longer referenced anywhere; reset is either not
implemented (e.g. ae3xx) or realized using a WDT (e.g. ag101).
Remove this left-over implementation in preparation for the removal of
the `addr` parameter in the entire tree.
Cc: Rick Chen <[email protected]>
Signed-off-by: Harald Seiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
SAMA7G5 supports slew rate configuration. Adapt the driver for this.
For switching frequencies lower than 50MHz the slew rate needs to
be enabled. Since most of the pins on SAMA7G5 fall into this category
enabled the slew rate by default.
Signed-off-by: Claudiu Beznea <[email protected]>
|
|
The u-boot-with-spl.imx is a concatenation of SPL and u-boot.uim.
The u-boot.uim is u-boot.bin wrapped in uImage. In case OF_SEPARATE
is enabled, the u-boot.bin does not contain control DT for U-Boot,
and so u-boot.uim does not contain the DT, and so u-boot-with-spl.imx
does not contain the DT, and a system where u-boot-with-spl.imx is
written to offset 1024B to the start of storage no longer boots, as
it is missing DT.
In case OF_SEPARATE is enabled, u-boot.img contains both u-boot.bin
and the necessary DTs. Therefore, use u-boot.img instead of u-boot.uim
to generate u-boot-with-spl.imx when OF_SEPARATE is enabled.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Christoph Niedermaier <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Instead of hard-coding the offset of DRAM entries in MMU table all over
the code, auto-detect the offset. This removes error-prone code which
would break e.g. in case the MMU table is modified.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Commit 247bbeb74c18 ("ARM: dts: imx8m: increase off-on delay on the SD Vcc
regulator") caused the imx8mq-evk board to not be able to store the
environment variables in the SD card.
Remove the u-boot,off-on-delay-us property to fix the regression.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Andrey Zhizhikin <[email protected]>
|
|
Add phy-reset-duration and phy-reset-post-delay to FEC node for PHY
reset, otherwise the PHY does not work correctly.
Signed-off-by: Ye Li <[email protected]>
|
|
The MX8M also contains a gigabit MAC, so define FEC_QUIRK_ENET_MAC.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped splash screen support as this needs to be properly
converted to DM and tested.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Import the imx23-evk devicetree files from Linux kernel
version 5.11.
This is in preparation for converting the mx23evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Import the imx51-babbage devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx51evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
The micro SD card slot uses GPIO3_13 as card detect pin, so describe
it in the devicetree.
This was noticed when converting imx53-qsb board to driver model
in U-Boot as the micro SD card was not getting detected.
After this change it is possible to load the dtb and zImage
from the SD card and boot Linux.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Import the imx53-qsb devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx53loco_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
The RGMII link delays can be set on either MAC or PHY side. Set the
rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY
setting, so that these definitions aren't used anymore throughout
the U-Boot.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Both NXP SoCs i.MX8 and i.MX8X have ENET gigabit MAC.
Define FEC_QUIRK_ENET_MAC for the imx8 platform and remove this
definition from configs of boards, based on MX8/MX8X.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Reviewed-By: Ramon Fried <[email protected]>
Acked-by: Oliver Graute <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The serial number OTP is similar to the imx7 version, except that the
register names are different. This also sets serial# directly, instead of
providing board_get_serial.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Add USB host boot support in stm32mp1 config
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
|
|
Remove duplicated uart nodes introduced with commit 62f95af92a3f
("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.9-rc4"),
because the uart nodes wasn't correctly ordered in alphabetic order.
Only cosmetic: the generated device tree don't change.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
|
|
|
|
The SPI NOR flash node name in main device tree for Turris Omnia is
called `spi-nor@0`.
Rename node spi-flash@0 in Turris Omnia's -u-boot.dtsi file to spi-nor@0
so that U-Boot does not try to probe the same SPI NOR device multiple
times.
Signed-off-by: Marek Behún <[email protected]>
Cc: Stefan Roese <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is the last ARCH_MPC8569 board, remove that support
as well.
Cc: Priyanka Jain <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
This device has four IOs connected to the SPI flash. Add the appropriate
bindings.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Leo Liang <[email protected]>
|
|
Commit "common: Drop asm/global_data.h from common header" added
asm/global_data.h into secure.h. However, secure.h will be included
by psci.S. Adding asm/global_data.h has caused compilation failure in
pcsi.S. Add "ifndef __ASSEMBLY__" in asm/global_data.h.
Signed-off-by: Siew Chin Lim <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- adds adc-keys button driver
- fix meson-saradc driver to get reference voltage
- add adc-keys test for sandbox
- enable adc-keys for VIM3 & VIM3L boards
- fix button.h build
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Fix ethernet on J721e
- Sync am335x DT nodes from Linux 5.9-rc7
- Minor Clock fixes
|
|
Fix the 'devivce' typo in arch/sandbox/include/asm/clk.h.
Signed-off-by: Dario Binacchi <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The commit 6337d53fdf45 ("arm: dts: sync am33xx with Linux 5.9-rc7")
synchronized the am33xx-clocks.dtsi file with Linux 5.9-rc7 with the
exception of two nodes. I think I was wrong and it is better to keep
the two files similar and possibly make changes to the *-u-boot.dtsi
files.
Signed-off-by: Dario Binacchi <[email protected]>
|
|
Signed-off-by: Sinan Akman <[email protected]>
|
|
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The A23, A33, H3, H5, A83T, V3 and Sochip S3 sun8i SoCs can mux uart1 on
GPIOs PG6 and PG7. This patch adds support for using uart1 on those pins
as boot console.
Signed-off-by: Tobias Schramm <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
It turns out that there is a magic bit in PRCM region which seemingly
makes PLLs work if it's enabled. Sadly, there is no documentation what
it does exactly, so we'll just mimick BSP boot0 behaviour and enable it
before any clock is set up.
Fixes: b18bd53d6cde ("sunxi: introduce support for H616 clocks")
Signed-off-by: Jernej Skrabec <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
- mmc_spi improvement
- added mmc-pwrseq to remove duplicated code
- fix response timeout after switch command
- sdhci: skip cache invalidation if DMA is not used
|
|
Before time, PWRSEQ is selected since below commit.
commit 262d34363373 ("board: amlogic: select PWRSEQ for all amlogic platform")
Select MMC_PWRSEQ config because of introducing CONFIG_MMC_PWRSEQ for
only eMMC module.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
- Improve interactions between SPL / OP-TEE and Linux in FIT images
|
|
Add test to validate dev->dma_offset is properly set on devices.
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Peter Robinson <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Introduce some new nodes in sandbox's test device-tree and dm tests in
order to validate dev_get_dma_range().
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Peter Robinson <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Add adc-keys device to the sandbox/test.dts and connect it to the channel
#3 of the sandbox_adc driver. The default values sampled by sandbox_adc
driver determines that button3 and button4 are released and button5 is
pressed.
Signed-off-by: Marek Szyprowski <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
The size is derived from the FIT image itself. Any alignment
requirements are machine-specific and known by the board code. Thus
the total length can be derived from the FIT image and knowledge of
the platform. The 'length' argument is redundant. Remove it.
Signed-off-by: Alexandru Gagniuc <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
CC: Matt Porter <[email protected]>
|
|
The definition follows the DSA binding in kernel and describes the switch,
its ports and PHYs. The switch node has the same structure as in Linux
and this patch enables it (and relevant ports) for the LS1028A RDB board.
ENETC PF6 is the 2nd Eth controller linked to the switch on LS1028A, it is
not used in U-Boot and was disabled. Ethernet port aliases were also
added to better manage the multitude of ports available now.
Signed-off-by: Alex Marginean <[email protected]>
Signed-off-by: Claudiu Manoil <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
|
|
Move gpio controller nodes from am33xx.dtsi to am33xx-l4.dtsi. Now both
files are more similar to those found in Linux 5.9-rc7. To be fully
operational as before it was also necessary to fix the am33xx-clock.dtsi
file. It too is now almost the same as the Linux kernel.
Signed-off-by: Dario Binacchi <[email protected]>
|
