| Age | Commit message (Collapse) | Author |
|---|
|
Add DT for DHCOR Testbench board, which is a testbench for testing of
DHCOR SoM during manufacturing. This is effectively a trimmed down
version of AV96 board with CSI-2 bridge, HDMI bridge, WiFi, Audio and
LEDs removed and used as GPIOs instead. Furthermore, the PMIC Buck3
is always configured from PMIC NVM to cater for both 1V8 and 3V3 SoM
variant.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
In case the regulator-always-on is present in regulator DT node,
the regulator is always reconfigured to the voltage set in DT on
probe, even if regulator_set_value() has been called before. Drop
the property from AV96 U-Boot DT and enable the regulator manually
in code, as the board already reconfigures the Buck3 regulator in
code per PMIC NVM content instead.
Fixes: 0adf10a87b1 ("ARM: dts: stm32: Configure Buck3 voltage per PMIC NVM on Avenger96")
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
into next
|
|
Pull this LPGPR unlock into common code, since it is used in multiple
systems already.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Commit 99c7cc58e12 ("ddr: imx: Add i.MX9 DDR controller driver")
contains an inobvious side-effect which renders all systems using
DRAM controller at 3732 MT/s unbootable. The change is located in
ddrphy_init_set_dfi_clk(), where the switch case statement entry
3732 changed to entry 3733, so any board with DDR calibration data
for 3732 MT/s operations needs to be updated to 3733 MT/s to match
the change.
Since there is currently only one such board, update the board instead
of handling both 3732 and 3733 options in the driver. It is likely the
NXP MX8MP RPA update will follow and use the later value too.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
Perform long overdue conversion of ad-hoc FMC2 EBI bus initialization
to upstream FMC2 EBI driver. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Enable d-cache early in SPL right after DRAM is started up.
This reduces U-Boot proper load time by 650ms when loaded
from SPI NOR.
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
To reduce code duplication, let the stm32 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <[email protected]>
Tested-by: Marek Vasut <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
To reduce code duplication, let the imx8 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <[email protected]>
Tested-by: Marek Vasut <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
To reduce code duplication, let the imx6 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <[email protected]>
Tested-by: Marek Vasut <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This is a starting point for unifying duplicate code in the DH board
files. The functions for setting up MAC addresses are very similar for
the i.MX6, i.MX8 and stm32mp1 based boards.
All pre-existing implementations follow the same logic:
(1) Check if ethaddr is already set in the environment
(2) If not, try to get it from a board specific location (e.g. fuse)
(3) If not, try to get it from eeprom
After this commit, (1) and (3) are implemented as common functions,
ready to be used by board specific files.
Furthermore there is an implementation of (2) for imx based boards.
Signed-off-by: Philip Oberfichtner <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Merge in v2022.07-rc5.
|
|
Replace call to fdt_*() functions and access to gd->fdt_blob
with call to ofnode_*() functions to support a live tree.
Tested-by: Marek Vasut <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20220523
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/12087
Additionally to u-boot-imx20200520:
- DH MX8MP
- i.MX GPIO: reading GPIO when direction is output
- Menlo i.MX53: switch to DM
And from u-boot-imx20200520:
- fix Verdin hang
- add pca9450 regulator
- conversion to DM_SERIAL
- NAND block handling
- fix crypto
- enable cache on some boards
- add ACC board (MX6)
|
|
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Before this commit device tree selection could rely solely on
differentiating the iMX6 processor variant Q and DL. After adding two new
carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs
makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02,
dhcom-picoitx or dhcom-pdk2) at compile time using
CONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
In the DH electronics iMX6 board file fix the outdated eeprom path by
using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
The Avenger96 board comes in multiple regulator configurations.
- rev.100 or rev.200 have Buck3 preconfigured to 3V3 operation on
boot and contains extra Enpirion EP53A8LQI DCDC converter which
supplies the IO. Reduce Buck3 voltage to 2V9 to not waste power.
- rev.200L have Buck3 preconfigured to 1V8 operation and have no
Enpirion EP53A8LQI DCDC anymore, the IO is supplied from Buck3.
Configure the Buck3 voltage on this board per PMIC NVM settings and
update buck3 voltage limits in DT passed to OS before booting OS to
prevent potential hardware damage.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
This function is empty, drop it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Steven Lawrance <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
The DHSOM uses different SPI NOR layout than the ST devkit, stop
pulling in the ST specific runtime mtdparts settings and adjust
the mtdparts accordingly.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <[email protected]>
|
|
DM_GPIO_HOG flag has been replaced by GPIO_HOG flag since a while in
commit 49b10cb49262 ("gpio: fixes for gpio-hog support").
And furthermore, gpio_hog_probe_all() is already called in board_r.c.
So gpio_hog_probe() can be removed from stm32mp1.c.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Marek Vasut <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
The stm32 platforms never had to support an ATAGs-based Linux Kernel,
so remove the bi_boot_params initialization.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Tested-by: Patrice Chotard <[email protected]>
Tested-by: Alexandru Gagniuc <[email protected]>
|
|
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <[email protected]>
|
|
Adding new DH electronics mailing list and update list of maintainers.
Signed-off-by: Christoph Niedermaier <[email protected]>
|
|
Use the correct name for STMicroelectronics phys config properties,
replace '_' by '-':
"st,eth_clk_sel" => "st,eth-clk-sel"
"st,eth-ref-clk-sel" => st,eth-clk-sel"
These property name are aligned with the upstreamed Linux kernel binding:
linux/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
See Linux kernel commit "dt-bindings: net: stmmac: add phys config
properties" merged in v5.1-rc1.
This patch allow to reuse the kernel device tree directly in U-Boot.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Currently the code sets eth1addr only if /ethernet1 alias exists in DT,
the node pointed to by the alias has "micrel,ks8851-mll" compatible
string, and the KSZ8851 CCR register read indicates programmed EEPROM
is not connected.
This is not sufficient to detect cases where the DT still contains the
KSZ8851 nodes, but the chip itself is not present. Extend the detection
to handle these cases.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Adding new DH electronics mailing list.
Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
There shouldn't be a need to use loadables propertyn because u-boot can be
pointed by firmware property. This change should also speedup boot process
because loadables property is list of strings which code is going through.
On the other hand firmware can just point to one image.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
In case the KS8851 has external EEPROM attached to it, do not set
eth1addr at all. The network stack will read the MAC out of the
KS8851 and set eth1addr accordingly.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851.
Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1.
The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address
of KS8851 was left uninitialized, so fix this.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
The new 587-200 DHCOR SoM is compatible with the 587-100 prototype,
hence just replicate the entries, as there is no pattern matching.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Include both PDK2 and DRC02 DTs in the DHCOM fitImage .its and implement
support in SPL to select the correct configuration entry for U-Boot by
using the machine compatible string from SPL DT.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Overriding the environment location is not necessary as the defconfig
for the relevant boards only enable SPI flash and nowhere sources which
are in the same order per default but having this explicit override
prevents using eMMC or SD card (or EXT4) as environment source.
Signed-off-by: Jakob Riepler <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This patch update the current gpio hog implementation with
the new API gpio_hog_probe_all() activated with CONFIG_GPIO_HOG.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1
and need to be updated for 800MHz support and only after the clock
tree initialization.
The VDDCORE voltage value is provided by clock driver, saved in global
variable opp_voltage_mv and udpated in SPL board_early_init_f(),
just after clock tree initialization.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Move function board_ddr_power_init() in a new file stpmic1 in
board/st/common to avoid duplicated code in each board using
stpmic1
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
This is needed to obtain the MAC from EEPROM/OTP only after the final
env is populated, otherwise the ethaddr might be overriden.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Claudius Heine <[email protected]>
Cc: Harald Seiler <[email protected]>
Cc: Ludwig Zenz <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
