| Age | Commit message (Collapse) | Author |
|---|
|
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Quoting Ye Li from NXP:
"We have confirmed with PMIC team, 0x35 is used only on early chips
and not used any more. 0x25 is the final address."
Fix it by merging power_pca9450a_init and power_pca9450b_init into one
function power_pca9450_init.
Signed-off-by: Sébastien Szymanski <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.
When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Silvano di Ninno <[email protected]>
Tested-by: Silvano di Ninno <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
In uMCTL2 Databook, for LPDDR4, it is recommended to set
this register to 1. This can avoid ddr bandwidth is lower
after booting with running for a while.
Reviewed-by: Ye Li <[email protected]>
Signed-off-by: Jian Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
1. set SCHED.rdwr_idle_gap=0
2. set SCHED.pageclose=1
Reviewed-by: Jacky Bai <[email protected]>
Signed-off-by: Jian Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Need to enable read urgent for NoC panic signal
Signed-off-by: Jian Li <[email protected]
Signed-off-by: Peng Fan <[email protected]>
|
|
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Acked-by: Magnus Lilja <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
There are a few remaining places where we say CONFIG_SECURE_BOOT rather
than CONFIG_IMX HAB. Update these instances.
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: NXP i.MX U-Boot Team <[email protected]>
Cc: Eddy Petrișor <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Priyanka Jain <[email protected]>
Fixes: d714a75fd4dc ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Xiaobo Xie <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ruchika Gupta <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <[email protected]>
Patch-cc: Ruchika Gupta <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Signed-off-by: Jagan Teki <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Timur Tabi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Priyanka Jain <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Po Liu <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Naveen Burmi <[email protected]>
Patch-cc: Ruchika Gupta <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ashish Kumar <[email protected]>
Patch-cc: Ruchika Gupta <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
s/booot/boot/g
The first ase is booot instead of boot and second u-booot instead of
u-boot.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.07
-----------------
- mx53: mx53menlo Convert to DM_ETH, fix fail boot
- imx8mp_evk: fix boot issue
- MX6, display5: fix environment
- drop warnings (watchdog) for i.MX8mm i.mx8mp
- enable bootaux for i.MX8M
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/695929999
|
|
- DM_ETH support for P2041RDB, T1024RDB, P5040DS, P3041DS, P4080DS, bug
fixes
- Add TBI PHY access through MII
- DDR: Rework errata workaround for A008109, A008378, 009942
|
|
We no need invoke the code, since spl framework could help
us do that.
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Use spl_early_init to replace spl_init, spl_init will be invoked
in board_init_r, we only need use spl_early_init to setup malloc
and scan early dt.
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
|
|
timer_init has been invoked in arch_cpu_init, no need to invoke
it again in board code.
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Drop useless getting ccm device, there is no need to explicted do this
in board code, and we not enable SPL CLK currently.
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Add a README file explaining the U-Boot build and SD card flash procedures.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Add the required changes for compiling with DM_ETH on the PPC
DPAA platforms.
Signed-off-by: Madalin Bucur <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Po Liu <[email protected]>
Cc: Qiang Zhao <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
|
|
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used.
The fsl-ls2080a-qds DTS will be used by default if there isn't a DTS
file specifically made for the current SERDES protocol.
This patch adds the necessary DPMAC nodes (DPMAC 1-8) for
protocol 42 (0x2A) on SD#1.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used. The fsl-ls2088a-qds DTS will be used by default if
there isn't a DTS file specifically made for the current SERDES
protocol.
This patch adds support for the on-board ports (DPMAC 1,2 and 4,5) found
on the SERDES protocols 21(0x15) and 29(0x1d) for SD#1.
On the LS1088AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as 2 input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 2 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
In case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled implement the
board_fit_config_name_match() function in order to choose the
appropriate DTS for the current SERDES protocol configuration.
Signed-off-by: Ioana Ciornei <[email protected]>
Reviewed-by: Razvan Ionut Cirjan <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <[email protected]>
Reviewed-by: Razvan Ionut Cirjan <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Fix up some incorrect code style in calls to functions in the log.h
header, mostly debug().
Signed-off-by: Simon Glass <[email protected]>
|
|
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Fix up some style problems in flash.h while we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
Previous patches allow UEFI secure variables to be stored in an RPMB
device using OPTEE. Add a config for the lx2160a hardware so the feature
gets at least compiled.
Signed-off-by: Ilias Apalodimas <[email protected]>
Remove superfluous differences to lx2160ardb_tfa_defconfig.
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Update fdt_file according to m4 parts state
Signed-off-by: Peng Fan <[email protected]>
|
|
Update fdt_file according to m4 parts state
Signed-off-by: Peng Fan <[email protected]>
|
|
Add code to check m4 partition booted or not, we will use this
to runtime set device tree file that passed to Linux Kernel.
Signed-off-by: Peng Fan <[email protected]>
|
|
Make sure that all devices that are powered up by SPL are powered down
before entering into the u-boot. Otherwise the subsystem/device will
never be powered down by SCFW, due to SPL and u-boot are in different
partitions.
Benefiting from power domain driver, this patch implements the function
"imx8_power_off_pd_devices" to power off all active devices.
Signed-off-by: Peng Fan <[email protected]>
|
|
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
|
