| Age | Commit message (Collapse) | Author |
|---|
|
A few boards still use ns16550_platdata structures, but assume the structure
is going to be in a specific order. By explicitly naming each entry,
this should also help 'future-proof' in the event the structure changes.
Tested on the Logic PD Torpedo + Wireless.
I only changed a handful of devices that used the same syntax as the Logic
board. Appologies if I missed one or stepped on toes. Thanks to Derald Woods
and Alexander Graf.
Signed-off-by: Adam Ford <[email protected]>
V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c
V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c
V4: Fix subject heading
V3: Remove reg_offset out in all the structs. It was reverted out, and and if
it did exist, it would get initialized to 0 by default.
V2: I hastily copy-pasted the boards without looking at the UART number.
This addresses 3 boards that use UART3 and not UART1.
Reviewed-by: Mugunthan V N <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Logic PD makes four different system on modules. This patch will auto
detect the board type and identify the corresponding device tree image.
V2:
Added 'default:' case to switch statement
Since board_late_init() is defined as int, we now return 0
Signed-off-by: Derald Woods <[email protected]>
Signed-off-by: Adam Ford <[email protected]>
|
|
I will take this over from Peter Barada, since I work with it daily
at Logic PD.
Signed-off-by: Adam Ford <[email protected]>
Acked-by: Peter Barada <[email protected]>
|
|
Android Fastboot requires USB. The TWL4030 PMIC on omap3_logic handles USB traffic.
This patch sets up the USB gadget and Android Fastboot to match what is done in the
omap3_beagle project.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Previously, Omap3_logic assumed X-loader was present. With this
patch, we can finally replace X-loader with an MLO generated by
U-Boot. This requires ECC to be setup to match the Linux Kernel
and the PBIAS confgured for the SD card.
Signed-off-by: Derald D. Woods <[email protected]>
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Enhance pin muxing to enable more board features and reduce power
based on Tony's device tree work.
Signed-off-by: Adam Ford <[email protected]>
|
|
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <[email protected]>
|
|
These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <[email protected]>
|
|
Convert to using the common config files.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <[email protected]>
|
|
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Tom Warren <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Macpaul Lin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: York Sun <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Philippe Reynes <[email protected]>
Cc: Eric Jarrige <[email protected]>
Cc: "David Müller" <[email protected]>
Cc: Phil Edworthy <[email protected]>
Cc: Robert Baldyga <[email protected]>
Cc: Torsten Koschorrek <[email protected]>
Cc: Anatolij Gustschin <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Łukasz Majewski <[email protected]>
|
|
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <[email protected]>
|
|
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <[email protected]>
Acked-by: Albert ARIBAUD <[email protected]>
Cc: Masahiro Yamada <[email protected]>
|
|
|
|
Adjust the configuration for the am33xx boards, including beagleboard,
to use driver model.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
Fix the following checkpatch issues:
CHECK: No space is necessary after a cast
\#39: FILE: arch/arm/include/asm/arch-am33xx/mux.h:39:
+#define PAD_CTRL_BASE 0x800
+#define OFFSET(x) (unsigned int) (&((struct pad_signals *) \
CHECK: Avoid CamelCase: <CONTROL_PADCONF_JTAG_nTRST>
\#284: FILE: arch/arm/include/asm/arch-omap3/mux.h:284:
+#define CONTROL_PADCONF_JTAG_nTRST 0x0A1C
ERROR: space required after that ',' (ctx:VxV)
\#446: FILE: arch/arm/include/asm/arch-omap3/mux.h:446:
+#define MUX_VAL(OFFSET,VALUE)\
^
Cc: Raphael Assenat <[email protected]>
Cc: Ilya Yanok <[email protected]>
Cc: Vaibhav Hiremath <[email protected]>
Cc: Peter Barada <[email protected]>
Cc: Grazvydas Ignotas <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Nagendra T S <[email protected]>
Cc: Nishanth Menon <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Igor Grinberg <[email protected]>
Acked-by: Stefan Roese <[email protected]>
|
|
Since commit ddaf5c8f3030050fcd356a1e49e3ee8f8f52c6d4
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <[email protected]>
Suggested-by: Tom Rini <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Zoom1 was wrongly setup for LAN91C96. Fix it by enabling
LAN9211.
Signed-off-by: Nishanth Menon <[email protected]>
|
|
zoom1 uses LAN9211 configured over GPMC Chip Select 1.
Signed-off-by: Nishanth Menon <[email protected]>
|
|
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.
Signed-off-by: Tom Rini <[email protected]>
|
|
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <[email protected]>
|
|
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <[email protected]>
Tested-by: Tom Rini <[email protected]>
Cc: Lars Poeschel <[email protected]>
Cc: Steve Sakoman <[email protected]>
Cc: Thomas Weber <[email protected]>
Cc: Tom Rix <[email protected]>
Cc: Grazvydas Ignotas <[email protected]>
Cc: Enric Balletbo i Serra <[email protected]>
Cc: Luca Ceresoli <[email protected]>
Cc: Igor Grinberg <[email protected]>
Cc: Ilya Yanok <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Nishanth Menon <[email protected]>
Cc: Pali Rohár <[email protected]>
Cc: Peter Barada <[email protected]>
Cc: Nagendra T S <[email protected]>
Cc: Michael Jones <[email protected]>
Cc: Raphael Assenat <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Cc: Andreas Bießmann <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Prafulla Wadaskar <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Vipin Kumar <[email protected]>
Cc: Tom Warren <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add check for write protection in omap mmc driver.
Signed-off-by: Nikita Kiryanov <[email protected]>
Signed-off-by: Igor Grinberg <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Implement driver check for card detection.
Signed-off-by: Nikita Kiryanov <[email protected]>
Signed-off-by: Igor Grinberg <[email protected]>
|
|
Use new musb framework instead of the old one on AM3517_EVM.
Signed-off-by: Ilya Yanok <[email protected]>
|
|
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Remove the prototypes for zoom2_serial_deviceN from serial.h . This
can't be done right away, as they are referenced from the zoom2
config file. Therefore, adjust the code so the config file only
specifies number of the port. Then, replace the simple return in
default_serial_console() with a switch across possible values, which
returns the zoom2_serial_deviceN . With such adjustment in place,
the exported prototypes in serial.h can be safely removed.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Anatolij Gustschin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Mike Frysinger <[email protected]>
Cc: C Nauman <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Michal Simek <[email protected]>
|
|
Fix up the rest of implementations of __stringify().
Signed-off-by: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Philippe Reynes <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <[email protected]>
Cc: Ilya Yanok <[email protected]>
Cc: Peter Barada <[email protected]>
Cc: Stefano Babic <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <[email protected]>
|
|
The initial checkin dropped pinmux setup for GPMC pins A6-A10, D0-D7 and
NCS1/2 necessary to access LAN92xx on Logic OMAP35x/DM37x modules.
Signed-off-by: Peter Barada <[email protected]>
|
|
This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo
reference boards. It assumes U-boot is loaded to SDRAM with the
help of another small bootloader (x-load) running from SRAM.
Signed-off-by: Peter Barada <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Igor Grinberg <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE
Cc: Vaibhav Hiremath <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
AM3517 specific CONTROL_PADCONF_* defines moved from board-specific
files to <asm/arch-omap3/mux.h>
Signed-off-by: Ilya Yanok <[email protected]>
|
|
gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output.
Signed-off-by: Joe Hershberger <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
setup_weimcs() and some macros are added to support the setup
for i.MX31 WEIM chip selects. As a compromise between verbosity
and readability an ASCII-art'ish bit comment is used instead of
bitfields.
All i.MX31 boards have been patched to use this approach using a
helper program to verify the changes.
Signed-off-by: Helmut Raiger <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <[email protected]>
|
