| Age | Commit message (Collapse) | Author |
|---|
|
The firmware sets local-bd-address, copy it when loading a new DT.
Signed-off-by: Fiona Klute <[email protected]>
Signed-off-by: Peter Robinson <[email protected]>
|
|
The /chosen/user-warnings property is created by the RPi firmware if
there are warnings to report, keep it to make debugging easier.
For example, if the firmware config.txt contains
"dtoverlay=error-example" and that example references an undefined
symbol "&nosuchdev" the warning can be read after boot:
$ cat /proc/device-tree/chosen/user-warnings
dterror: can't find symbol 'nosuchdev'
Failed to resolve overlay 'error-example'
Signed-off-by: Fiona Klute <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Signed-off-by: Peter Robinson <[email protected]>
|
|
The functions fdt_simplefb_add_node and fdt_simplefb_enable_and_mem_rsv
are only available if CONFIG_FDT_SIMPLEFB is enabled.
Signed-off-by: Martin Stolpe <[email protected]>
Acked-by: Matthias Brugger <[email protected]>
Signed-off-by: Peter Robinson <[email protected]>
|
|
The Raspberry Pi foundation have released the Raspberry
Pi 500, CM5 an CM5 lite devices so add the assoicated
revision identifers so we can detect them.
Signed-off-by: Peter Robinson <[email protected]>
Acked-by: Matthias Brugger <[email protected]>
|
|
Prepare v2025.01-rc5
|
|
This returns a devicetree and updates a parameter with an error code.
Swap it, since this fits better with the way U-Boot normally works. It
also (more easily) allows leaving the existing pointer unchanged.
No yaks were harmed in this change, but there is a very small code-size
reduction.
For sifive, the OF_BOARD option must be set for the function to be
called, so there is no point in checking it again. Also OF_SEPARATE is
defined always.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
[trini: Update total_compute]
Signed-off-by: Tom Rini <[email protected]>
|
|
Since RPI works well using EFI and has no size limitations with regards
to U-Boot, add the needed structures to support capsule updates.
While at it update the most commonly used defconfigs and include capsule
support and U-Boot commands needed by EFI
Tested-by: Sughosh Ganu <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
For a lot of usecases, such as display, camera, media
the Raspberry Pi needs a lot more CMA than distros
configure as default so we should pass this parameter
through so things work as expected. Fix a spelling
mistake while we're at it.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Matthias Brugger <[email protected]>
|
|
Add the necessary DSDT files copied from tianocore to boot the RPi4.
In addition generate a board specific SSDT to dynamically enable/disable
ACPI devices based on FDT. This is required to support the various variants
and boot options. It also allows to test the code on QEMU 9.0 without
modifications, since it doesn't emulate PCIe yet.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Patrick Rudolph <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Matthias Brugger <[email protected]>
Cc: Peter Robinson <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
Updates for RPi for 2024.10:
- board: rpi: remove leftover CONFIG_HW_WATCHDOG block
- arm: bcm283x: remove unused empty hw_watchdog_disable
- board: raspberrypi: Fix format specifier for printing rev_scheme
- Revert "arm: dts: bcm283x: Add minimal smbios information"
|
|
This was added in commit 45a6d231b2f (bcm2835_wdt: support for the
BCM2835/2836 watchdog), which did do 'select HW_WATCHDOG'. That
incarnation of the watchdog driver later got removed in
c7adc0b5f98 (watchdog: bcm2835_wdt: Remove unused BCM283x watchdog
driver and its references), but this block was left behind.
Another rpi watchdog driver has since been added, but that does not
select HW_WATCHDOG, so this remains dead and unused. Remove it.
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
|
|
rev_scheme is an unsigned integer and must not be printed
as a signed integer.
Signed-off-by: Francois Berder <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
Firmware on RPi5 return error on board revision query
through firmware interface, but on the other hand it fills
"linux,revision" in "system" node, so use it to detect board
revision.
system {
linux,revision = <0xc04170>;
linux,serial = <0x6cf44e80 0x3c533ede>;
};
Reviewed-by: Matthias Brugger <[email protected]>
Tested-by: Jens Maus <[email protected]>
Tested-by: Darko Alavanja <[email protected]>
Signed-off-by: Ivan T. Ivanov <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Use the new environment format so we can drop most of the config.h file.
Signed-off-by: Simon Glass <[email protected]>
|
|
board_get_usable_ram_top() returns a physical address that is stored in
gd->ram_top. The return type of the function should be phys_addr_t like the
current type of gd->ram_top.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
When raspberrpi-4b platform boots up, there are 2 sets of same bootup
log displayed on HDMI monitor screen, it looks like the screen is split
into 2 parts. The root cause is that video format of u-boot is different
from kernel. The fixing "a8r8g8b8" video format is used in u-boot, but
"r5g6b5" video format from framebuffer node is used in kernel image. In
order to avoid weird display status on screen, it needs to set the correct
parameter for simple framebuffer node even if it has existed.
Signed-off-by: Meng Li <[email protected]>
|
|
Update the Raspberry Pi Zero 2W device tree file
name to match what landed upstream.
Signed-off-by: Peter Robinson <[email protected]>
|
|
Some Raspberry Pi 400 boards, specifically rev 1.1, have a different
address for the ethernet PHY device than what is provided by the kernel
DTB. The correct address is provided by the firmware, so we should carry
it over into the loaded device tree so that ethernet works on such boards.
Signed-off-by: Antoine Mazeas <[email protected]>
Signed-off-by: Peter Robinson <[email protected]>
|
|
The RPI firmware adjusts several property values in the dtb it passes
to u-boot depending on the board/SoC revision. Inherit some of these
when u-boot loads a dtb itself. Specificaly copy:
* /model: The firmware provides a more specific string
* /memreserve: The firmware defines a reserved range, better keep it
* emmc2bus and pcie0 dma-ranges: The C0T revision of the bcm2711 Soc (as
present on rpi 400 and some rpi 4B boards) has different values for
these then the B0T revision. So these need to be adjusted to boot on
these boards
* blconfig: The firmware defines the memory area where the blconfig
stored. Copy those over so it can be enabled.
* /chosen/kaslr-seed: The firmware generates a kaslr seed, take advantage
of that.
Signed-off-by: Sjoerd Simons <[email protected]>
Signed-off-by: Antoine Mazeas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Peter Robinson <[email protected]>
|
|
Peter accpeted to step up as a co-maintainer for the RPis.
Reflect that in the corresponding MAINTAINERS files.
Signed-off-by: Matthias Brugger <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
|
|
This file is being removed so drop remaining references to it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Commit 37dc958947ed ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947ed ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Prepare v2022.01-rc4
|
|
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
|
|
The Raspberry Pi Foundation released the new Zero 2 W which we
want to detect, so we can detect the correct device tree file name.
Signed-off-by: Peter Robinson <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Raspberry Pi Foundation has updated their documentation so update
the URL to the latest place to find the HW device revision codes.
Signed-off-by: Peter Robinson <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Prepare v2021.10-rc5
|
|
It appears that RPi firmware has already added framebuffer
node under /chosen, at least on RPi 2 versions. So check
for this and don't add duplicate node.
Signed-off-by: Ivan T. Ivanov <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Phil Sutter <[email protected]>
Cc: Stefan Bosch <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The Raspberry Pi Foundation released the new Compute Module 4 which we
want to detect, so we can enable Ethernet on it and know the correct
device tree file name.
Note that this sets the Ethernet option to true since the official CM4
IO board has an Ethernet port. But that might not be the case when using
custom ones.
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
Tested-by: Peter Robinson <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Raspberry Pi Foundation released the new RPi400 which we want to
detect, so we can enable Ethernet on it and know the correct device tree
file name.
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
Tested-by: Peter Robinson <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
When RPi4 is booted from USB Mass Storage, the firmware reports 947MiB of
the ARM memory (948 in case of the standard SD-card boot). This value is
not MMU_SECTION_SIZE aligned, so the dram_bank_mmu_setup() skips mapping
of the last 1MiB. This later causes u-boot in ARM 32bit mode to freeze,
because it relocated itself into that unmapped memory and fails to
execute.
Fix this by limiting the size of the first bank to the multiple of
MMU_SECTION_SIZE.
Signed-off-by: Marek Szyprowski <[email protected]>
Reviewed-by: Nicolas Saenz Julienne <[email protected]>
Tested-by: Jaehoon Chung <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Virtually all callers of this function do the rounding on their own.
Some do it right, some don't. Instead of doing this in each caller,
do the rounding in efi_add_memory_map(). Change the size parameter
to bytes instead of pages and remove aligning and size calculation in
all callers.
There is no more need to make the original efi_add_memory_map() (which
takes pages as size) available outside the module. Thus rename it to
efi_add_memory_map_pg() and make it static to prevent further misuse
outside the module.
Signed-off-by: Michael Walle <[email protected]>
Add missing comma in sunxi_display.c.
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Some systems may use a slightly larger stub to do PSCI for booting the RPi
family. The number of pages has been made configurable so that operating
systems building U-Boot for use in these kinds of environments can reserve
more memory in the EFI memory map.
Signed-off-by: Kyle Evans <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
While the nearly-universal default for the Raspberry Pi family is to use
spin tables and the spin table implementation provided by the Raspberry Pi
Foundation, FreeBSD and others may use a PSCI implementation instead.
Accommodate these setups by allowing them to configure for more than one
page to be reserved in the initial reservation. The default reservation
remains as one page.
Signed-off-by: Kyle Evans <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Up to now we only update the DRAM banks when we are define
CONFIG_BCM2711. But our one binary approach uses a config that supports
BCM2837 and BCM2711. As a result we only see one gibibyte of RAM on
Raspberry Pi 4, even if it has more RAM.
Fix this by calling dram_init_banksize.
Fixes: 5694090670 ("ARM: defconfig: add unified config for RPi3 and RPi4")
Signed-off-by: Matthias Brugger <[email protected]>
|
|
To update the dram bank information from device-tree we use
fdtdec_decode_ram_size() which expectes the the size-cells and
address-cells to be defined in the memory node. For normal system RAM
these values are defined in the root node. When the values differ from
the default values defined in the spec, we can end up with wrong RAM
bank information.
Switch to the "standard" way to update the RAM bank information to
avoid this.
Fixes: 9de5b89e4c ("rpi4: enable dram bank initialization")
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
For bcm283x based on arm64 we also have to change the mm_region.
Add assign this in mach_cpu_init() so we can create now one binary
for RPi3 and RPi4.
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The fw_dtb_pointer was defined in the assembly code, which makes him
live in section .text_rest
Put that's not necessary, we can push the variable in the .data section.
This will prevent relocation errors like:
board/raspberrypi/rpi/rpi.c:317:(.text.board_get_usable_ram_top+0x8):
relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC against symbol
`fw_dtb_pointer' defined in .text section in board/raspberrypi/rpi/built-in.o
Signed-off-by: Matthias Brugger <[email protected]>
|
|
When booting through the efi stub, the memory map get's created by
reading the dram bank information. Depending on the version of the RPi4
this information changes. Read the device tree to initialize the dram
bank data structure. This way the kernel is able to access the whole
range of available memory.
Signed-off-by: Matthias Brugger <[email protected]>
|
|
Define the memory map for the BCM2711 based on the dt configuration
available in the Raspberry Pi kernel fork.
Signed-off-by: Andrei Gherzan <[email protected]>
[mb: BCM2838 -> BCM2711]
Signed-off-by: Matthias Brugger <[email protected]>
|
|
The Raspebrry Pi 4 uses the new revision code scheme as documented by
the foundation. This change adds an entry for this board as well.
Signed-off-by: Andrei Gherzan <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
