| Age | Commit message (Collapse) | Author |
|---|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
These changes bring mainline back into line with the configurations
that were originally set in our stable BSP.
Signed-off-by: Jon Nettleton <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Signed-off-by: Florian Klink <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The order of members in struct hws_topology_map is cas_wl, cas_l. The
comments in the original db-88f6820-gp.c had this wrong and have been
copied to other Armada-385 based boards. Practically this hasn't made a
difference since all these boards set both cas_wl and cas_l to 0
(autodetect) but if there were ever a board that did need to set these
explicitly they would run into unexpected issued.
Update the comments to reflect the correct order of structure members.
Reported-by: Tobi Wulff <[email protected]>
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
There is no need call setup_display() from SPL code, so move it to
board_init(), which executes only in U-Boot proper.
Reported-by: Stefano Babic <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
Signed-off-by: Baruch Siach <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The hummingboard2 is slightly different to the cubox i and to the
hummingboard. The GPIO pin info to probe came from solidruns
for of u-boot on github.
https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589
I have tested on a hummingboard-edge witha imx6 solo and 512mb of
ram.
Signed-off-by: Dennis Gilmore <[email protected]>
|
|
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.
Signed-off-by: Breno Lima <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <[email protected]>
CC: Fabio Estevam <[email protected]>
CC: Akshay Bhat <[email protected]>
CC: Ken Lin <[email protected]>
CC: Marek Vasut <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: "Sébastien Szymanski" <[email protected]>
CC: Christian Gmeiner <[email protected]>
CC: Stefan Roese <[email protected]>
CC: Patrick Bruenn <[email protected]>
CC: Troy Kisky <[email protected]>
CC: Nikita Kiryanov <[email protected]>
CC: Otavio Salvador <[email protected]>
CC: "Eric Bénard" <[email protected]>
CC: Jagan Teki <[email protected]>
CC: Ye Li <[email protected]>
CC: Peng Fan <[email protected]>
CC: Adrian Alonso <[email protected]>
CC: Alison Wang <[email protected]>
CC: Tim Harvey <[email protected]>
CC: Martin Donnelly <[email protected]>
CC: Marcin Niestroj <[email protected]>
CC: Lukasz Majewski <[email protected]>
CC: Adam Ford <[email protected]>
CC: "Albert ARIBAUD (3ADEV)" <[email protected]>
CC: Boris Brezillon <[email protected]>
CC: Soeren Moch <[email protected]>
CC: Richard Hu <[email protected]>
CC: Wig Cheng <[email protected]>
CC: Vanessa Maegima <[email protected]>
CC: Max Krummenacher <[email protected]>
CC: Stefan Agner <[email protected]>
CC: Markus Niebel <[email protected]>
CC: Breno Lima <[email protected]>
CC: Francesco Montefoschi <[email protected]>
CC: Jaehoon Chung <[email protected]>
CC: Scott Wood <[email protected]>
CC: Joe Hershberger <[email protected]>
CC: Anatolij Gustschin <[email protected]>
CC: Simon Glass <[email protected]>
CC: "Andrew F. Davis" <[email protected]>
CC: "Łukasz Majewski" <[email protected]>
CC: Patrice Chotard <[email protected]>
CC: Nobuhiro Iwamatsu <[email protected]>
CC: Hans de Goede <[email protected]>
CC: Masahiro Yamada <[email protected]>
CC: Stephen Warren <[email protected]>
CC: Andre Przywara <[email protected]>
CC: "Álvaro Fernández Rojas" <[email protected]>
CC: York Sun <[email protected]>
CC: Xiaoliang Yang <[email protected]>
CC: Chen-Yu Tsai <[email protected]>
CC: George McCollister <[email protected]>
CC: Sven Ebenfeld <[email protected]>
CC: Filip Brozovic <[email protected]>
CC: Petr Kulhavy <[email protected]>
CC: Eric Nelson <[email protected]>
CC: Bai Ping <[email protected]>
CC: Anson Huang <[email protected]>
CC: Sanchayan Maity <[email protected]>
CC: Lokesh Vutla <[email protected]>
CC: Patrick Delaunay <[email protected]>
CC: Gary Bisson <[email protected]>
CC: Alexander Graf <[email protected]>
CC: [email protected]
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Christian Gmeiner <[email protected]>
|
|
The Cubox-i and Hummingboard series of devices have an option of
SATA on board, and depending on how the fuses are blown even the
option to boot SPL from SATA. So enable support for it so it can
be used to boot the OS from if people desire.
Cc: Fabio Estevam <[email protected]>
Signed-off-by: Peter Robinson <[email protected]>
Acked-by: Fabio Estevam <[email protected]>
|
|
The clearfog uses Armada 388.
Cc: Stefan Roese <[email protected]>
Signed-off-by: Baruch Siach <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The DDR3 training code for Marvell A38X currently computes 1t timing
when given board topology map of the Turris Omnia, but Omnia needs 2t.
This patch adds support for enforcing the 2t timing in struct
hws_topology_map, through a new enum hws_timing, which can assume
following values:
HWS_TIM_DEFAULT - default behaviour, compute whether to enable 2t
from the number of CSs
HWS_TIM_1T - enforce 1t
HWS_TIM_2T - enforce 2t
This patch also sets all the board topology maps (db-88f6820-amc,
db-88f6820-gp, controlcenterdc and clearfog) to have timing set to
HWS_TIM_DEFAULT.
Signed-off-by: Marek Behun <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Use GPIO19 which is wired to the uSOM phy reset signal in order to reset
the uSOM's 1512 Gigabit Ethernet phy.
This GPIO is valid on ClearFog rev 2.1 and newer.
Taken from SolidRun's specialised u-boot, see
https://github.com/SolidRun/u-boot-armada38x/commit/f906e3df172e07ac82cdd87b278d7896949262ea
Signed-off-by: Patrick Wildt <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <[email protected]>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <[email protected]>
|
|
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Eric Nelson <[email protected]>
|
|
It's not necessary to implement the is_mx6q function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
|
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Minkyu Kang <[email protected]>
|
|
Merging all the board specific Kconfig options into the main Kconfig file
for mach-mvebu makes things easier to maintain.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Rabeeh Khoury <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
Update my email address to the NXP account.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
We currently support various versions of Solidrun mx6 boards, so
remove the obsolete comment.
Reported-by: Jon Nettleton <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional:
Booting from net ...
FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.
As per the AR8035 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and keep the reset low for 10ms.
Also add a 100us delay after deasserting the reset line
to guarantee that the PHY ID can be read correctly and the Atheros
PHY can be loaded as per Troy Kisky's suggestion.
Signed-off-by: Fabio Estevam <[email protected]>
Tested-by: Tom Rini <[email protected]>
|
|
Remove duplicated SYS_SOC Kconfig entry from board Kconfig,
because we have this entry in arch/arm/cpu/armv7/mx6/Kconfig.
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Christian Gmeiner <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Troy Kisky <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Cc: "Eric Bénard" <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Markus Niebel <[email protected]>
Cc: Otavio Salvador <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Acked-by: Christian Gmeiner <[email protected]>
Acked-by: Markus Niebel <[email protected]>
Acked-by: Troy Kisky <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.
Initialize ddr_type for different boards which enable SPL.
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Fabio Estevam <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.
Signed-off-by: Peng Fan <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Nikolaos Pasaloukos <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Hummingboard dual-lite is picking the incorrect calibration structure.
Fix it so that it can boot.
While at it, also fix p1_mpdgctrl1 register to match Solid-run's
setting.
Reported-by: Andrei Gherzan <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Tested-by: Andrei Gherzan <[email protected]>
|
|
The 'mx6-microsom' directory was only used for the previous mx6solo
hummingboard support, which has been removed in favour of the SPL
version.
Remove the remaining piece of the old mx6solo hummingboard support.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
Cubox-i boards are also supported, so update the README file.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Hummingboard dual, dual-lite and solo are now supported via SPL mechanism.
Remove the previous hummingboard support, which does not use SPL and supported
only the solo variant.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Configure PAD_ENET_RXD0/RXD1 pads as pull down because these pads are directly
connected to the Atheros 8035/8030 although they should be functional
only in the RMII mode - 8030.
Signed-off-by: Rabeeh Khoury <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-By: Vagrant Cascadian <[email protected]>
|
|
mx6cuboxi sometimes fails to recognize the Ethernet PHY:
Net: Phy 0 not found
The explanation for this behavior comes from from Rabeeh Khoury:
"The LED_ACT pin on the carrier-one boards had a pull down that
forces the phy address to 0x0; where on CuBox-i and the production
HummingBoard that pin is connected directly to LED that depending
on the pull down strength of the LED it might be sampled as '0' or '1' thus
the phy address might appear as either address 0x0 or 0x4."
"This is AR8035 implementation; in reset stage the LED pin is configured as
input, and pull up/down does matter. In this case it configures the PHY
address.
After reset is deasserted the same LED pin becomes output and then
according to the previous pull/up it should be active high/low"
One way to properly fix this behavior is to place external pull-up/down
resistors in the LED line, but from a software standpoint we can fix it
by telling phy_find_by_mask() to scan the PHY at addresses
0x0 and 0x4.
Reported-by: Vagrant Cascadian <[email protected]>
Signed-off-by: Rabeeh Khoury <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-By: Vagrant Cascadian <[email protected]>
|
|
Enable USB Host1 port.
Signed-off-by: Rabeeh Khoury <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Tested-By: Vagrant Cascadian <[email protected]>
|
|
Add HDMI output using PLL5 as the source for the IPU clocks,
and accurate VESA timings.
These settings are based on the patch from Soeren Moch <[email protected]>
submitted for the tbs2910 mx6 based board.
It allows the display to work properly at 1024x768@60.
This should make the hdmi output signal compatible with most if not all
modern displays.
Signed-off-by: Jon Nettleton <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Rabeeh Khoury <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-by: Vagrant Cascadian <[email protected]>
|
|
Instead of hardcoding the 'fdtfile' variable, let's detect the SoC and
board variant on the fly and change the dtb name.
Based on the scheme done on am335x board.
Signed-off-by: Fabio Estevam <[email protected]>
Tested-By: Vagrant Cascadian <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Introduce is_hummingboard() function that reads GPIOs that can distinguish
between Cubox-i and Hummingboard.
Print the board name accordingly.
Based on a patch from Rabeeh Khoury.
Signed-off-by: Rabeeh Khoury <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad. Add support for the different SoC/memory sizes
combinations.
DDR initialization values were extracted from Solid-run internal U-boot.
Tested on a CuBox-i4Pro, HummingBoard-i2eX and HummingBoard-i1.
Signed-off-by: Rabeeh Khoury <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad.
Use IOMUX_PADS() macro in order to prepare for the multi-SoC support.
Also pass 'MX6QDL' in the defconfig to indicate it.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
The correct name of the defconfig file is 'mx6cuboxi_defconfig'.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.
For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/
Based on the work from Jon Nettleton and Rabeeh Khoury.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Jon Nettleton <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <[email protected]>
Acked-by: Albert ARIBAUD <[email protected]>
Cc: Masahiro Yamada <[email protected]>
|
|
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Conflicts:
boards.cfg
Signed-off-by: Stefano Babic <[email protected]>
|
|
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <[email protected]>
Suggested-by: Tom Rini <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <[email protected]>
|
