| Age | Commit message (Collapse) | Author |
|---|
|
MPU's region setup can be factorized between STM32F4/F7/H7 SoCs family
and used a common MPU's region config.
Only one exception for STM32H7 which doesn't have device area
located at 0xA000 0000.
For STM32F4, configure_clocks() need to be moved from arch_cpu_init()
to board_early_init_f().
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Vikas Manocha <[email protected]>
|
|
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Vikas Manocha <[email protected]>
|
|
Uniformize STMicroelectronics copyrights headers for STV0991
related code.
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Uniformize STMicroelectronics copyrights headers for STM32
related code.
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Uniformize all STMicroelectronics copyrights headers for STi
related code.
Signed-off-by: Patrice Chotard <[email protected]>
|
|
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add usb_gadget_handle_interrupts(), board_usb_init(),
board_usb_cleanup() and g_dnl_board_usb_cable_connected()
callbacks needed for FASTBOOT support
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Migrate all FMC defines from arch/arm/include/asm/arch-stm32f7/fmc.h
to drivers/ram/stm32_sdram.c
This will avoid to add an additionnal arch-stm32xx/fmc.h file when
a new stm32 family soc will be introduced.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Vikas Manocha <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This allow to remove include/dm/platform_data/serial_stm32x7.h
which was included in the past by stm32x7 driver and by
stm32f746-disco.c board file.
Since patch 42bf5e7c27 "serial: stm32f7: add device tree support"
this file is no more needed in board file.
Signed-off-by: Patrice Chotard <[email protected]>
Acked-by: Vikas MANOCHA <[email protected]>
|
|
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Signed-off-by: Vikas Manocha <[email protected]>
|
|
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <[email protected]>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <[email protected]>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <[email protected]>
|
|
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <[email protected]>
|
|
Signed-off-by: Vikas Manocha <[email protected]>
cc: Christophe KERELLO <[email protected]>
|
|
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <[email protected]>
cc: Christophe KERELLO <[email protected]>
|
|
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: Vikas Manocha <[email protected]>
cc: Christophe KERELLO <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This patch also removes the sdram/fmc clock enable from board specific
code.
Signed-off-by: Vikas Manocha <[email protected]>
cc: Christophe KERELLO <[email protected]>
|
|
As driver model takes care of pin control configuraion, this patch also
removes the sdram/fmc pin configuration.
Signed-off-by: Vikas Manocha <[email protected]>
cc: Christophe KERELLO <[email protected]>
|
|
Signed-off-by: Vikas Manocha <[email protected]>
cc: Christophe KERELLO <[email protected]>
|
|
Signed-off-by: Patrice Chotard <[email protected]>
|
|
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
It also removes the qspi pin configuration done during the
board initialization.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
It also removes the ethernet pin configuration done during the board
initialization.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
And remove the uart pin configuration from board initialization.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Before clock driver availability it was required to enable usart1 clock
for serial init but now with clock driver is taking care of usart1 clock.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
This patch adds device tree support for stm32f7 serial driver & removes serial
platform data structure.
Signed-off-by: Vikas Manocha <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This is a 96Board compliant board based on STiH410 SoC:
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- SATA
- HDMI
- 2 x USB2.0 type A
- 1 x USB2.0 type micro-AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This patch adds support for the QSPI IP found in stm32f7 devices.
Signed-off-by: Michael Kurz <[email protected]>
|
|
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Use the clock setup function defined in clock.c instead of setting the
clock bits directly in the drivers.
Remove register definitions of RCC in rcc.h as these are already
defined in the struct in stm32.h
Signed-off-by: Michael Kurz <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
Reviewed-by: Vikas Manocha <[email protected]>
|
|
Cleanup stm32f7 files:
- use BIT macro
- use GENMASK macro
- use rcc struct instead of macro additions
Add missing stm32f7 register in rcc struct
Signed-off-by: Michael Kurz <[email protected]>
Acked-by: Vikas MANOCHA<[email protected]>
|
|
Per Vikas' request, the problem this commit is supposed to be solving is
something he doesn't see and further this introduces additional hardware
requirements.
This reverts commit 4b2fd720a7b2f78c42d1565edf4c67f378c65440.
Signed-off-by: Tom Rini <[email protected]>
|
|
This change is to remove a halt at about 200KiB
while sending a large(1MiB) binary to a micro controller using USART1.
USART1 is connected to a PC via an on-board ST-Link debugger
that also functions as a USB-Serial converter.
However, it seems to loss some data occasionally.
So I changed the serial port to USART6 and connected it to the PC using
an FTDI USB-Serial cable, therefore the transmission was successfully
completed.
Signed-off-by: Toshifumi NISHINAGA <[email protected]>
|
|
This patch adds SDRAM support for stm32f746 discovery board.
This patch depends on previous patch.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <[email protected]>
|
|
This patch adds support for stm32f7 family & stm32f746 board.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
This patch removes the gpio clock enable from gpio driver & move it in the
board code, making it possible to use the gpio driver with other socs.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
This patch removes the uart clock enable from serial driver & move it in the
board code.
Signed-off-by: Vikas Manocha <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Signed-off-by: Kamil Lulko <[email protected]>
Cc: Simon Glass <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Signed-off-by: Kamil Lulko <[email protected]>
|
|
These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <[email protected]>
|
|
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <[email protected]>
To: Albert Aribaud <[email protected]>
To: Tom Rini <[email protected]>
To: Kamil Lulko <[email protected]>
Cc: [email protected]
|
|
|
|
When "scripts/get_maintainer.pl" parses "board/.../MAINTAINERS",
it uses the line containing board name as delimiter.
Without this line, the script happily mixes the lines from current
board MAINTAINERS file with lines from another file.
Fix it by adding a reasonable board name.
Tested by comparing output of:
cat board/st/stm32f429-discovery/MAINTAINERS
./scripts/get_maintainer.pl -f board/st/stm32f429-discovery
Signed-off-by: Antonio Borneo <[email protected]>
To: [email protected]
To: Kamil Lulko <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <[email protected]>
Reviewed-by: Jagannadh Teki <[email protected]>
|
|
This patch ignores the serial port static platform data at compilation time
in case of device tree control.
Signed-off-by: Vikas Manocha <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add the stm32F4 board's serial ports support.
User can use it easily.
The user only need to edit the number of the usart.
The patch also fix the serial print out.
Last, this version of patch fix the first patch checkpatch.pl error.
Thanks to Kamil Lulko.
Signed-off-by: kunhuahuang <[email protected]>
|
|
Signed-off-by: Kamil Lulko <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
