| Age | Commit message (Collapse) | Author |
|---|
|
Fixed typo for doc/README.imximage on respective imximage.cfg files.
Cc: Tom Rini <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Acked-by: Peng Fan <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Since commit a13d3757f7df ("warp: Use imx_ddr_size() for calculating the
DDR size") warp board no longer boots.
The reason for the breakage is that the warp board is using the DDR
configuration from mx6slevk. A fundamental difference between warp and
mx6slevk is that warp only uses one DDR chip select while mx6slevk uses two.
The imx_ddr() function calculates the RAM size in runtime by reading the
values of registers MDCTL and MDMISC.
So in order to fix this warp boot issue, create a imximage DDR file specific
to warp, where the MDCTL register is configured to only activates a single
chip select.
Reported-by: Breno Lima <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Tested-by: Breno Lima <[email protected]>
|
|
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Minkyu Kang <[email protected]>
|
|
Remove duplicated SYS_SOC Kconfig entry from board Kconfig,
because we have this entry in arch/arm/cpu/armv7/mx6/Kconfig.
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Christian Gmeiner <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Troy Kisky <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Cc: "Eric Bénard" <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Markus Niebel <[email protected]>
Cc: Otavio Salvador <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Acked-by: Christian Gmeiner <[email protected]>
Acked-by: Markus Niebel <[email protected]>
Acked-by: Troy Kisky <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
Warp has a MAX77696 PMIC connected via I2C1 bus.
Add support for it.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
After the mx6 config consolidation, 'save' command is no longer
recognized.
Pass the full command name 'saveenv' instead.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Fix the spelling of 'successful'.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Provide instructions on how to upgrade U-boot in the eMMC.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Otavio Salvador <[email protected]>
|
|
With UMS support we are able to flash the eMMC from U-boot, which is very
convenient.
Add UMS support to make the eMMC flashing process easier.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Otavio Salvador <[email protected]>
|
|
The WaRP Board is a Wearable Reference Plaform. The board features:
- Freescale i.MX6 SoloLite processor with 512MB of RAM
- Freescale FXOS8700CQ 6-axis Xtrinsic sensor
- Freescale Kinetis KL16 MCU
- Freescale Xtrinsic MMA955xL intelligent motion sensing platform
The board implements a hybrid architecture to address the evolving
needs of the wearables market. The platform consists of a main board
and an example daughtercard with the ability to add additional
daughtercards for different usage models.
For more information about the project, visit:
http://www.warpboard.org/
Signed-off-by: Otavio Salvador <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
