| Age | Commit message (Collapse) | Author |
|---|
|
Sparrow Hawk EVTA1
The Retronix R-Car V4H Sparrow Hawk old revision EVTA1 does not have MicroSD
voltage switch populated on the board, therefore the board supports only 3V3
and non-UHS MicroSD cards. While the EVTB1 board is populated with Winbond
W77Q51NW SPI NOR, the EVTA1 board is populated with Spansion S25FS512S SPI
NOR, those those SPI NOR IDs to discern the two board revisions and apply
the MicroSD related DT changes.
The MicroSD related DT changes modify the regulator node, which is now a
regulator-fixed and supplies only 3V3, and remove sd-uhs-sdr50 and
sd-uhs-sdr104 properties from the MicroSD slot controller node.
The MicroSD related DT changes cannot be applied as DTO, because the base
DT contains nodes which have to be removed in case of EVTA1, but have to
be present in case of EVTB1 and newer revisions of the board. Because the
EVTA1 is an old revision of the board that is not generally available, it
is better to special case it and keep the base DT compatible with EVTB1
and newer revisions of the board which are actually available.
Signed-off-by: Marek Vasut <[email protected]>
|
|
When writing the EEPROM fails, the command usage help text is displayed
after the error message. We should only display the error message instead.
If writing the EEPROM fails, return CMD_RET_FAILURE (1) instead of
CMD_RET_USAGE (-1).
Fixes: aea1bd95b61e ("eeprom: starfive: Enable ID EEPROM configuration")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Acked-by: E Shattow <[email protected]>
|
|
Add Voyager board maintainer.
Signed-off-by: Randolph Sheng-Kai Lin <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
|
|
Introduce Voyager board specific code, including
- dram info
- shared cache enabling
Signed-off-by: Randolph Sheng-Kai Lin <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
|
|
The Voyager is Andes' first RISC-V development board.
It is built around Qilai SoC,
which includes Andes AX45MP quad-core cluster.
Introduce the Kconfig entry for the Voyager board.
Signed-off-by: Randolph Sheng-Kai Lin <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
|
|
A new system controller driver has been created to make code modular and
improve and clean code. Update and remove functions to account for these
additional drivers.
Signed-off-by: Jamie Gibbons <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Enable the MPFS mailbox and system controller drivers for use with the
Icicle kit. These functions are crucial for the board setup functions
that run in the Icicle board file - mpfs_icicle.c.
Signed-off-by: Jamie Gibbons <[email protected]>
Acked-by: Leo Yu-Chi Liang <[email protected]>
|
|
Move ethernet mac address setting to ft_board_setup() to remove the need
for fdt set in custom boot script.
Signed-off-by: Jamie Gibbons <[email protected]>
Acked-by: Leo Yu-Chi Liang <[email protected]>
|
|
There is no reason to use OF_BOARD for MBV because reduced DT is used by
SPL and full DT is passed via u-boot.img or u-boot.itb. There is no reason
to pick up DTB from certain address.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
watchdogs in U-Boot"
This series from Wadim Egorov <[email protected]> cleans up how
watchdogs are handled on some phytec TI K3 platforms.
Link: https://lore.kernel.org/r/[email protected]
|
|
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value.
Users can enable the watchdog to monitor the boot process until userspace
or OS takes over to serve the watchdog.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga
This pull request introduces initial U-Boot support for Agilex7 M-series, along
with several enhancements and cleanups across existing Agilex platforms. Key
changes include new board support, DDR driver additions, updated device trees,
and broader SoCFPGA SPL improvements.
Highlights:
- Agilex7 M-series bring-up:
- Basic DT support and board initialization for Agilex7 M-series SoC and
SoCDK.
- New sdram_agilex7m DDR driver with UIBSSM mailbox support and HBM support.
- Clock driver support for Agilex7 M-series.
- New defconfig: socfpga_agilex7m_defconfig.
- Agilex and Agilex5 enhancements:
- Improved SPL support: ASYNC interrupt enabling, system manager init
refactor, and cold scratch register usage.
- Updated firewall probing and watchdog support in SPL.
- Cleaned up DDR code, added secure region support for ATF, and improved warm
reset handling.
- Device Tree and config updates:
- Migration to upstream Linux DT layout for Agilex platforms.
- Consolidated socfpga_agilex_defconfig and removed deprecated configs.
- Platform-specific environment variables for Distro Boot added.
- Driver fixes and cleanups:
- dwc_eth_xgmac and clk-agilex cleanup and improvements.
- Several coverity and style fixes.
Contributions in this PR are from Alif Zakuan Yuslaimi, Tingting Meng, and
Andrew Goodbody. This patch set has been tested on Agilex 5 devkit, Agilex
devkit and Agilex7m devkit.
Passing all pipeline tests at SoCFPGA U-boot custodian
https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27318
|
|
use the new email address for community work.
While at it, cleanup git shortlog output, by adding
fixes in .mailmap
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Update Makefile to support Agilex7 M-series platform enablement.
Signed-off-by: Tingting Meng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Add platform related files for new platform Agilex7 M-series.
Signed-off-by: Tingting Meng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Agilex7 M-series support has been added using upstream Linux DTS.
socfpga_agilex_socdk-u-boot.dtsi was updated to support both Agilex and
Agilex7 M-series platforms.
Signed-off-by: Tingting Meng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
The base address of system manager can be retrieved
using DT framework through the system manager driver.
Enable system manager support for Agilex by probing the
system manager driver to initialize during SPL boot up.
Signed-off-by: Boon Khai Ng <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Refactor system manager initialization by searching for system manager
alias in Agilex5 device tree instead of manually passing node name to
the device model calling function
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
For phyCORE-i.MX93 SoMs with i.MX93 parts running in VOLT_LOW_DRIVE mode
(SoCs with speed grade fuse set to 900 MHz) reduce usdhc clocks from 400
MHz to 266 MHz. Do this in board code since global imx9 board_fix_fdt()
is not used in case of phycore-imx93 board since commit d3b9b7996889
("board: phytec: imx93: Add eeprom-based hardware introspection").
While at it, add a note to ft_board_setup() function to inform that
fixup for Linux device-tree is taken care by ft_system_setup() in imx9
global arch/arm/mach-imx/imx9/soc.c implementation.
Signed-off-by: Primoz Fiser <[email protected]>
|
|
Enable SoC pull up for USB OTG ID pin in SPL. There is no dedicated pull up
resistor on the SoM itself, and the pull up is mandatory for correct USB OTG
ID pin detection. U-Boot proper already configures the USB OTG ID pin pull
up via DT pinctrl node entry.
Signed-off-by: Marek Vasut <[email protected]>
Tested-by: Christoph Niedermaier <[email protected]>
|
|
(SGH-i927) support
The Galaxy R (GT-I9103) and Captivate Glide (SGH-i927) are both Tegra 2
based Samsung smartphones released in 2011. They both feature 1 GB of RAM
and 8 GB of expandable flash memory. The key difference is that the
Captivate Glide has an OLED panel (contrary to LCD in Galaxy R) and a
QWERTY keyboard in form factor of a slider.
Signed-off-by: Ion Agorria <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
The Pegatron Chagall (originally built by Pegatron, but later rebranded by
other vendors under names Fujitsu Stylistic M532, Olivetti Olipad 3,
Siragon 4N, Realpad Bunaken, DNS AirTab P110w / P110g etc) is a mostly
business-oriented tablet sold in 2012 in different variants, mostly in
Europe, with slight differences in storage size (16GB/32GB) and presence
of built-in cellular modem.
Tested-by: Raffaele Tranquillini <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/27236
- Add support for STM32 TIMERS and STM32 PWM on STM32MP25
- Add STM32MP13xx SPL and OpTee-OS start support
- Fix header misuse in stm32 reset drivers
- Fix STMicroelectronics spelling
- Fix clk-stm32h7 wrong macros used in register read
- Fix PRE_CON_BUF_ADDR on STM32MP13
- Fix clock identifier passed to struct scmi_clk_parent_set_in
- Fix stm32 reset for STM32F4/F7 and H7
- Enable OF_UPSTREAM_BUILD_VENDOR for stm32mp13_defconfig
- Add STM32MP23 SoC and stm32mp235f-dk board support
|
|
Add STM32MP23 support which is a cost optimized of STM32MP25.
More details available at:
https://www.st.com/en/microcontrollers-microprocessors/stm32mp2-series.html
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Add default STM32MP13xx debug UART initialization. This is similar
to STM32MP15xx debug UART initialization, except the RCC registers
are at different offsets and the UART pinmux pins are different.
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
The STM32MP13xx PMIC initialization for DDR3 DRAM type is similar
to the STM32MP15xx PMIC initialization, except the VTT rail is not
enabled. Fill in the STM32MP13xx support.
Reviewed-by: Patrice Chotard <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2025.10 cycle:
This feature set includes the addition of new sama7d65 SoC and a new
board named sama7d65-curiosity.
|
|
So far developers seem to use three popular boards:
- Avaota A1: dev board with USB 3.0, dual Ethernet, small display
- X96QPro+: TV box with Gigabit Ethernet, USB 3.0, eMMC
- Radxa A5E: small dev board with USB3/M.2 2230 (muxed), dual Ethernet
Add the defconfig files for those boards, containing the DRAM parameters
and the usual Kconfig options.
Signed-off-by: Andre Przywara <[email protected]>
|
|
Add the basic Kconfig options, addresses and other values for the
existing Kconfig settings for the new Allwinner A523/T527/H728 SoC.
Signed-off-by: Andre Przywara <[email protected]>
|
|
- Enhanced e850-96 support
|
|
Add initial mmc defconfig to boot from SDMMC1.
Signed-off-by: Ryan Wanner <[email protected]>
Signed-off-by: Romain Sioen <[email protected]>
|
|
Add board specific functions for sama7d65_curiosity.
Signed-off-by: Ryan Wanner <[email protected]>
|
|
Make it possible to update E850-96 firmware binaries using EFI Capsule
Update mechanism. For example, to update the U-Boot binary, the capsule
file can be generated like this:
$ ./tools/mkeficapsule --index 4 \
--guid 629578c3-ffb3-4a89-ac0c-611840727779 \
u-boot.bin capsule4.bin
The resulting 'capsule4.bin' should be copied to ESP partition (in
/boot/efi/EFI/UpdateCapsule/ directory). Then after reboot U-Boot will
update the 'bootloader' area in eMMC Boot Partition A (boot0) and remove
the capsule file, by EFI boot manager executed as a part of Standard
Boot:
Applying capsule capsule4.bin succeeded.
Reboot after firmware update.
The kernel will also expose the ESRT table information via SysFS in
/sys/firmware/efi/esrt/entries.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Matches downstream Android-Q partition table created by flashing the
modified gpt.img [1], with added ESP partition (EFI System Partition).
It's an A/B slotted Android partition table, so it's possible to boot
Android from this table using Android GBL EFI app. Tested using
AOSP/main images for E850-96 with booting via GBL app.
[1] https://gitlab.com/Linaro/96boards/e850-96/tools/gpt/-/blob/master/gpt_layout_uboot_q_ab
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Add 'dfu_alt_info' environment variable which contains:
- Linux eMMC partitions ('esp' and 'rootfs')
- eMMC Boot Partition A layout, where all the firmware reside
It makes it possible to update the bootloader (U-Boot). All sizes in
'dfu_alt_info' are given in 512B blocks (LBA). eMMC size is 58.2 GiB.
The eMMC Boot Partition A (mmc0boot0) layout looks like this:
boot0 partition (4 MiB)
0x0 +----------------------------------+
| fwbl1 (12 KiB) |
0x18 +----------------------------------+
| epbl (76 KiB) |
0xb0 +----------------------------------+
| bl2 (256 KiB) |
0x2b0 +----------------------------------+
| dram_train (16 KiB) |
0x2d0 +----------------------------------+
| ect_test (50 KiB) |
0x334 +----------------------------------+
| acpm_test (130 KiB) |
0x438 +----------------------------------+
| bootloader (2 MiB) |
0x1438 +----------------------------------+
| el3_mon (256 KiB) |
0x1638 +----------------------------------+
where U-Boot should be flashed into 'bootloader' partition. So U-Boot
binary size should be 2 MiB or less. The whole boot0 partition is 4 MiB,
but only 2.8 MiB is currently used.
With this change, the U-Boot binary can be updated on eMMC like this:
=> dfu 0 mmc 0
$ dfu-util -D u-boot.bin -a bootloader
Looking at E850-96 booting diagram at [1,2], it's easy to see how these
binaries are being executed in the same order they are placed in
mmc0boot0 area. E.g. fwbl1 is definitely BL1 (software part of Boot
ROM). So it's obvious the ROM code just reads the binary from eMMC at
0x0 offset into RAM (SRAM?) and executes it.
All mentioned images can be found at [3], as stated in E850-96 U-Boot
documentation. 'dram_train', 'ect_test' and 'acpm_test' areas should be
ignored -- they are not flashed with real images.
[1] doc/board/samsung/e850-96.rst
[2] https://docs.u-boot.org/en/latest/board/samsung/e850-96.html
[3] https://gitlab.com/Linaro/96boards/e850-96/images/-/tree/master/images
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Setup "serial#" environment variable from the chip ID. The chip ID is
read from Exynos850 SoC OTP (One Time Programmable) memory, which acts
like an EEPROM and contains unique SoC ID. This "serial#" variable is
further used for "fastboot devices" serial number, etc.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27149
- Add support for the NXP imx93 frdm board.
- imx93_evk and phycore-imx93 cleanups.
- Convert imx6dl-sielaff to OF_UPSTREAM and fix serial download mode boot.
- Fix crash in imx power-domain.
- Migrate Phytec imx8mm boards to standard boot.
- Fix smatch warnings.
|
|
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <[email protected]>
Tested-by: Adam Ford <[email protected]> #imx8mm_beacon
Tested-by: Bryan Brattlof <[email protected]>
Acked-by: Peng Fan <[email protected]> #NXP boards
|
|
uclass_find_next_device always returns 0, so instead make it a void and
update calling sites.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
Add the initial board support for the NXP i.MX93 FRDM board:
https://www.nxp.com/design/design-center/development-boards-and-designs/frdm-i-mx-93-development-board:FRDM-IMX93
Based on the NXP U-Boot code.
There were attempts to upstream the board devicetree, but it has not been
accepted upstream yet:
https://lore.kernel.org/linux-arm-kernel/[email protected]/
Once it reaches upstream, we can switch to OF_UPSTREAM.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
There is no PMIC and USB related C code in this file.
Remove these unneeded header files.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
The board name is "i.MX93 EVK", not "MEK".
Fix it accordingly.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
remove boot logic from shared env file for phyboard-polis and
phygate-tauri.
Adjust configs for both boards as well.
Space at the beginning of addressable RAM is reserved for space used via
standard boot env variables. CONFIG_SYS_LOAD_ADDR is set to the lowest
address behind the standard boot variables reserved space.
Signed-off-by: Yannic Moog <[email protected]>
|
|
Add PID4 0216 Verdin iMX8M Mini Quad 2GB WB IT to config block handling.
Signed-off-by: Vitor Soares <[email protected]>
Acked-by: Francesco Dolcini <[email protected]>
|
|
Drop unused include files from the PHYTEC phyCORE-i.MX93 board code.
Signed-off-by: Primoz Fiser <[email protected]>
|
|
Drop unused define for PCA9450 PMIC register which is already part of
the header file <power/pca9450.h> since commit 1d0d25704345 ("imx93_evk:
spl: update pmic settings").
Signed-off-by: Primoz Fiser <[email protected]>
|
|
The mainainers for these boards have changed.
Signed-off-by: Holger Brunck <[email protected]>
Signed-off-by: Tomas Alvarez Vanoli <[email protected]>
|
|
Move the call to configure the qrio i2c deblock pins earlier.
Before this, the call was happening after the first attempt to deblock
the SDP EEPROM, which resulted in a not correct sequence.
Signed-off-by: Tomas Alvarez Vanoli <[email protected]>
Signed-off-by: Holger Brunck <[email protected]>
|
