| Age | Commit message (Collapse) | Author |
|---|
|
return is not a function, parentheses are not required
Signed-off-by: Osama Abdelkader <[email protected]>
|
|
serial_reinit_all() is only available when CONFIG DM_SERIAL is disabled
and CONFIG_SERIAL is enabled.
Signed-off-by: Aditya Dutt <[email protected]>
|
|
Hiding a qualifier such as "volatile" inside a typedef makes the code
much harder to understand. Since addr and dummy being
volatile-qualified are important for the correctness of the test code,
make it more obvious by spelling it out as "volatile ulong".
Signed-off-by: Rasmus Villemoes <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
A function call itself for every word written or read+written in these
loops is bad enough. But since the memory test must be run with dcache
disabled, the schedule() call, traversing the linked list of
registered cyclic clients, and accessing the 'struct cyclic_info' for
each to see if any are due for a callback, is quite expensive. On a
beagleboneblack, testing a modest 16MiB region takes 2.5 minutes:
=> dcache off
=> time mtest 0x81000000 0x82000000 0 1
Testing 81000000 ... 82000000:
Iteration: 1
Tested 1 iteration(s) with 0 errors.
time: 2 minutes, 28.946 seconds
There is really no need for calling schedule() so frequently. It is
quite easy to limit the calls to once for every 256 words by using a
u8 variable. With that, the same test as above becomes 37 times
faster:
=> dcache off
=> time mtest 0x81000000 0x82000000 0 1
Testing 81000000 ... 82000000:
Iteration: 1
Tested 1 iteration(s) with 0 errors.
time: 4.052 seconds
Note that we are still making a total of
3 loops * (4 * 2^20 words/loop) / (256 words/call) = 49152 calls
during those ~4000 milliseconds, so the schedule() calls are still
done less than 0.1ms apart.
These numbers are just for a beagleboneblack, other boards may have a
slower memory, but we are _two orders of magnitude_ away from
schedule() "only" being called at 100Hz, which is still more than
enough to ensure any watchdog is kept happy.
Signed-off-by: Rasmus Villemoes <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
It is obviously important that the addr pointer used to access the
memory region being tested is volatile-qualified, to prevent the
compiler from optimizing out the "write this value, read it back,
check that it is what we expect".
However, none of these auxiliary variables have any such need for,
effectively, being forced to live on the stack and cause each and
every reference to them to do a memory access.
This makes the memtest about 15% faster on a beagleboneblack.
Before:
=> dcache off
=> time mtest 0x81000000 0x81100000 0 1
Testing 81000000 ... 81100000:
Iteration: 1
Tested 1 iteration(s) with 0 errors.
time: 10.868 seconds
After:
=> dcache off
=> time mtest 0x81000000 0x81100000 0 1
Testing 81000000 ... 81100000:
Iteration: 1
Tested 1 iteration(s) with 0 errors.
time: 9.209 seconds
[Without the 'dcache off', there's no difference in the time, about
0.6s, but the memtest cannot usefully be done with dcache enabled.]
Signed-off-by: Rasmus Villemoes <[email protected]>
Tested-by: Anshul Dalal <[email protected]>
|
|
Linux features a flash_speed speed test from the mtd-utils suite, U-Boot
does not. Benchmarks are useful for speed improvement developments as
well as troubleshooting or regression testing sometimes.
Enable a benchmark option to enable this feature.
Example of output on a Nuvoton platform:
MA35D1> mtd read nor0 0x81000000 0 0x10000
Reading 65536 byte(s) at offset 0x00000000
MA35D1> mtd read.benchmark nor0 0x81000000 0 0x10000
Reading 65536 byte(s) at offset 0x00000000
Read speed: 3752kiB/s
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
option to show nand dump data ecc corrected as opposed to just raw
Signed-off-by: david regan <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
show characters with nand dump similar to md
along with offset into NAND
Signed-off-by: david regan <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
nand read/write raw change 'count' to 'pages' since count is ambiguous
Signed-off-by: david regan <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
bug fix MTD_OOB_AUTO to MTD_OPS_AUTO_OOB since MTD_OOB_AUTO does not exist
Fixes: dfe64e2c8973 ("mtd: resync with Linux-3.7.1")
Signed-off-by: david regan <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
The legacy network stack sets net_try_count to 1 at the beginning of the
net_loop() function. This is required for net_start_again() to work
properly. Therefore, set the variable accordingly in the do_ping()
function when NET_LWIP=y. This fixes an issue where a ping to an
unreachable destination would run twice on the same network device. For
example with qemu_arm64_lwip_defconfig:
=> dhcp
DHCP client bound to address 10.0.2.15 (3 ms)
=> ping 10.0.0.1
Using virtio-net#32 device
ping failed; host 10.0.0.1 is not alive
Using virtio-net#32 device
ping failed; host 10.0.0.1 is not alive
=> QEMU: Terminated
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Now that sys_check_timeouts() is called in net_lwip_rx(), there is no
need to call it from the SNTP receive loop. Remove the redundant call.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Introduce the DNS Kconfig symbol so that various network commands may
use host names without the dns command (CMD_DNS) being selected.
Signed-off-by: Jerome Forissier <[email protected]>
CC: E Shattow <[email protected]>
|
|
It is sometimes useful to be able to boot via EFI using a Linux initrd.
Add support for this.
Fix a 'specifiy' typo while here.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Mark Kettenis <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
The size of free memory should be $lmb_base - $ram_base.
Signed-off-by: Shiji Yang <[email protected]>
|
|
Add i3c command file to support select, get i3c device
target list, read and write operation.
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
coverity scan reported issue:
** CID 583415: Integer handling issues (INTEGER_OVERFLOW)
/cmd/i2c.c: 369 in do_i2c_write()
change the length variable into type int.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Use the same logic as is used for MAC address where bdi shows mac address
for current device where index (idx) is used to point to correct IP address
which is read and show.
Signed-off-by: Michal Simek <[email protected]>
|
|
mac_read_from_eeprom() always display debug infos, and this messes up the
display of the "Net:" section details:
Before:
Net: EEPROM: TlvInfo v1 len=172
eth0: ethernet@11c20000
After:
Net: eth0: ethernet@11c20000
Fix by moving unconditional "EEPROM: " header into each message and
changing debug message to use log_debug().
Signed-off-by: Hugo Villeneuve <[email protected]>
|
|
Fix typo errors in comments and error message by replacing EERPOM->EEPROM.
Signed-off-by: Hugo Villeneuve <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
|
|
In do_bootvx the environment variable 'bootdev' is fetched and copied
into a buffer without confirming that it will not overflow that buffer.
Use strlcpy to ensure that the buffer will not be overflowed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
The generic name 'EFI' would be more useful for common EFI features. At
present it just refers to the EFI app and stub, which is confusing.
Rename it to EFI_CLIENT
Signed-off-by: Simon Glass <[email protected]>
|
|
uclass_find_next_device always returns 0, so instead make it a void and
update calling sites.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
Errors reported by GCC 14.2 when enabling FPGA commands and
drivers. Also many style fixes as reported by checkpatch.pl on the
diffs. Most changes in stratixII.c which has been reorganized as well
to avoid the top function prototypes.
No functional changes.
Signed-off-by: Pieter Van Trappen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
In cmd/fpga.c, change some `debug` calls to `log_err` for important
user feedback and use CMD_RET_FAILURE in favor of CMD_RET_USAGE due to
its long output which hides the actual, useful return message. Change
the remaining `debug` calls to `log_debug`. Remove all 'fpga:' and
__func__ strings as log_* has this covered.
For `do_fpga_loads`, move up the `do_fpga_check_params` call for more
consistent command output; use a constant instead of multiple '5' use.
In drivers/fpga/zynq*.c, change 'up to' to 'above' which corrects this
confusing/wrong statement.
Signed-off-by: Pieter Van Trappen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
The buffer for a name to be copied into must also contain the
terminating 0 byte but strlen returns the length of the string without
counting that 0 byte. Adjust the length checks to take this into
account.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-i2c
i2c updates for v2025.10
- i2c Kconfig updates from Tom
- add some driver dependencies
- added missing include delay.h in iproc_i2c.c
- i2c: muxes: Add PCA9541 i2c arbitrator driver
from Padmarao Begari
- pca954x: add pca9545 support
from Frank Wunderlich
- cmd: i2c: fix build when CFG_SYS_I2C_NOPROBES defined with DM_I2C
From Holger Brunck
|
|
When DM_I2C is enabled and CFG_SYS_I2C_NOPROBES is defined, the
building is broken due to already existing 'bus' local variable.
Rename udevice 'bus' to 'cur_bus' to fix this.
Signed-off-by: Holger Brunck <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/27056
- Fix unused access in ufetch
- Add missing clock for SM8650
- Port the Linux SPMI GPIO driver and port over SM8550 (other platforms
should follow)
|
|
The local variable size is not assigned to before it is used
for the first time. Correct this.
This issue was found by Smatch.
Fixes: 86d462c05d57 (cmd: add a fetch utility)
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Casey Connolly <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Casey Connolly <[email protected]>
|
|
Svyatoslav Ryhel <[email protected]> says:
Add uclass for HW AES cryptographic devices found on some devices, like
Tegra20/Tegra30 SoC AES engine.
Link: https://lore.kernel.org/r/[email protected]
|
|
This adds new aes subcommands to use interface provided by AES UCLASS which
can be used to expose HW AES engines.
Signed-off-by: Ion Agorria <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27010
- Fix the i.MX8M Nano GPU path.
- Enable RNG support for KASLR on Toradex i.MX8 boards.
- Enable watchdog and clock driver for imx6ulz_smm_m2b.
- Tighten dependencies on CMD_BLOB.
- Remove the rest of i.MX31 support.
|
|
In order to build this command we need to have configured some other
board specific features. Express that requirement in Kconfig as well.
Signed-off-by: Tom Rini <[email protected]>
|
|
In order for this command to build we need to compile
drivers/crypto/fsl/fsl_blob.c and this in turn includes
drivers/crypto/fsl/jr.h which references "ccsr_sec_t" which is only a
defined type for SYS_FSL_SEC_COMPAT >= 4. Express that requirement in
Kconfig as well.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
We have had no platforms that make use of this since 2015, so drop it.
Signed-off-by: Tom Rini <[email protected]>
|
|
We have had no platforms that make use of this since 2021, so drop it.
Signed-off-by: Tom Rini <[email protected]>
|
|
ft_board_setup_ex()"
João Paulo Gonçalves <[email protected]> says:
In some use cases, board-specific device tree changes must not be overwritten
by system fixups. Although U-Boot provides ft_board_setup_ex() for this
purpose, it is currently only used on TI Keystone. This series makes
ft_board_setup_ex() a generic option, allowing its use by other architectures
and boards.
Additionally, considering that Toradex Verdin-AM62P hardware lifetime
guarantees are based on a 105°C junction temperature (while TI AM62Px supports
up to 125°C), this series implements necessary changes within TI K3 AM62P and
Toradex board code. These changes include exporting common fixup device Tree
functions used in TI K3 for board-code access and also fixup for AM62P thermal
zones to correctly reflect the number of CPU nodes according to the SoC part
number.
Link: https://lore.kernel.org/r/20250623-am62p-fdt-fixup-trip-points-v1-0-12355eb6a72f@toradex.com
|
|
In some use cases, board-specific device tree changes must not be
overwritten by system fixups. Although U-Boot provides
ft_board_setup_ex() for this purpose, it is currently only used on TI
Keystone. Make ft_board_setup_ex() to be a generic option, allowing its
use by other architectures/boards. To maintain backward compatibility,
enable it by default on TI Keystone.
Signed-off-by: João Paulo Gonçalves <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx changes for v2025.10-rc1
cmd:
- Introduce CMD_HELP Kconfig option
fpga:
- Fix in intel_smd_mb
mini:
- Remove simple-bus driver and description
- Disable CMD_HELP
firmware:
- Fix dependencies
- Switch to new SMC firmware format
cadence qspi:
- Fix read/write STIG mode
- Set tshsl_ns to at least one sclk_ns
sdhci:
- Call sdhci reset if wired
zynqmp-clk:
- Add support for DPLL clock source
zynqmp:
- Sync clock ID bindings with Linux
- defconfig updates
- Enable rng-seed generation
versal:
- Fix clock dependency
versal2:
- defconfig updates
- Enable sysreset
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYIAB0WIQSXAixArPbWpRanWW+rB/7wTvUR9QUCaG0Z7AAKCRCrB/7wTvUR
# 9YyCAQCseYDzYZbdh4e2g6LirVovzPv2LUNRFInYSKleegOjiwEAgQ0p9wZ0hNNj
# TpWf6sOKa/0ad3bZBtvbuV0G9WpqWAA=
# =2pbC
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 08 Jul 2025 07:15:24 AM CST
# gpg: using EDDSA key 97022C40ACF6D6A516A7596FAB07FEF04EF511F5
# gpg: Can't check signature: No public key
|
|
Add option to disable help command in size constrained systems to save some
space. There is also no need to have ifdefs around CMDLINE because all
commands depends on it.
And also mark cmd_help dependency in test_help.py.
Reviewed-by: Peter Robinson <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/c17f825fb8a74e1d1912a3fd09a9a880c84a8bfd.1751286059.git.michal.simek@amd.com
|
|
Implement the sntp command when NET_LWIP=y.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Update the ping command so that a host name is accepted in addition to
an IP address, provided DNS support is enabled.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
When calling "dns <hostname> <varname>", do not print out the IP address
of <hostname> onto the console. Print it only when no variable is
passed. The reason is to be able to call do_dns() from another command
in need of the DNS services without polluting the output.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
The DNS loop checks for a non-zero IP address after DNS resolution, but
the address is in fact never copied into the context. Fix that.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Split net/lwip/wget.c in two: one part which implements CONFIG_WGET
stays in net/ while the part that implements CONFIG_CMD_WGET is moved
into cmd/.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Move each command in cmd/net-lwip.c into its own file
(cmd/lwip/${cmd}.c).
Suggested-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Prepare to split the ping command from cmd/net-lwip.c by moving the
implementation from net/lwip/dns.c to cmd/lwip.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Prepare to split the dns command from cmd/net-lwip.c by moving the
implementation from net/lwip/dns.c to cmd/lwip.
Signed-off-by: Jerome Forissier <[email protected]>
|
|
|
