| Age | Commit message (Collapse) | Author |
|---|
|
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <[email protected]>
Signed-off-by: Suniel Mahesh <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <[email protected]>
Signed-off-by: Suniel Mahesh <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Commit 65cc0e2a65d2 ("global: Move remaining CONFIG_SYS_* to CFG_SYS_*")
renamed CONFIG_SYS_UBOOT_START to CFG_SYS_UBOOT_START. Unfortunately,
this meant that the value was no longer available to the Makefile. This
caused imxrt to fail to boot. All the other boards that used this
variable were unaffected because they were using the default value
which is CONFIG_TEXT_BASE.
This commit converts CFG_SYS_UBOOT_START to Kconfig and sets the default
value to CONFIG_TEXT_BASE.
Suggested-by: Marek Vasut <[email protected]>
Suggested-by: Tom Rini <[email protected]>
Signed-off-by: Jesse Taube <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <[email protected]>
|
|
On x86 devices we use CAR (Cache-As-RAM) to hold the malloc() region in
SPL, since SDRAM is not set up yet. This means that driver model stores
its tables in this region.
When preparing to jump from SPL to U-Boot proper, we must disable CAR, so
that the CPU can uses the caches normally. This means that driver model
tables become inaccessible. From there until we jump to U-Boot proper, we
must avoid using driver model.
This is only a problem on boards which operate this way, for example
chromebook_link64
Add a flag to indicate that driver model is dead and should not be used.
It can be used in SPL to avoid hanging the machine.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This CONFIG is used but is not given a value by some boards. Use
a default value of 0 explicitly, rather than relying on the 0 value
provided by CONFIG_SPL_LOAD_FIT_ADDRESS
This will allow us to make SPL_LOAD_FIT_ADDRESS depend on SPL_LOAD_FIT
as it should.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case anything errors out during the SDP transfer, detach
the controller instead of bailing out right away. This way,
the controller can be reattached on next attempt.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
spl_blk_load_image() should not return an uninitialized value if
blk_get_devnum_by_uclass_id() fails.
Fixes: 8ce6a2e17577 ("spl: blk: Support loading images from fs")
Reported-by: Xavier Drudis Ferran <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Xavier Drudis Ferran <[email protected]>
|
|
spl_invoke_opensbi function is not returned to SPL. Thus, we need to
set __noreturn function attribute.
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Prepare v2023.10-rc3
Signed-off-by: Tom Rini <[email protected]>
|
|
There is no requirement that a partition 1 exists in a partition table.
We should not try to retrieve information about it.
We should not even try reading with partition number
CONFIG_SYS_NVME_BOOT_PARTITION here as this is done in the fs_set_blk_dev()
call anyway.
Fixes: 8ce6a2e17577 ("spl: blk: Support loading images from fs")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
When Falcon Mode is enabled, SPL needs to check the value of
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR. Unfortunately, it was using the
CONFIG_VAL(SYS_MMCSD_RAW_MODE_ARGS_SECTOR) which converts it into
CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR when CONFIG_SPL_BUILD is
enabled. CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR does not exist in
common/spl/Kconfig. Replaced with
defined(CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR).
Signed-off-by: Elena Popa <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Allow loading a FIT image via semihosting in SPL.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
All SPL hash algorithm options are collected in lib/Kconfig. Move
SPL_CRC32 there as well.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
There is another SPL_MD5 option defined in lib/Kconfig.
Renaming SPL_MD5_SUPPORT introduced duplicate option with
different description. As for now FIT and hash algorithm options
are not related to each others, removing a duplicate option seems OK.
Fixes: 4b00fd1a84c ("Kconfig: Rename SPL_MD5_SUPPORT to SPL_MD5")
Signed-off-by: Oleksandr Suvorov <[email protected]>
|
|
MMC, SATA, and USB may be using PCI based controllers.
Initialize the PCI sub-system before trying to boot.
Remove the initialization for NVMe that is now redundant.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Mayuresh Chitale <[email protected]>
|
|
Loading u-boot.itb from device 0x00, partition 0x0f fails with:
Trying to boot from NVME
Device 0: Vendor: 0x4x Rev: 8.0.50 Prod: nvme-1
Type: Hard Disk
Capacity: 3814.6 MB = 3.7 GB (7812500 x 512)
** Invalid partition 21 **
Couldn't find partition nvme 0:15
Like the command line interface fs_det_blk_dev() expects that the device
number and the partition number are hexadecimal.
Fixes: 8ce6a2e17577 ("spl: blk: Support loading images from fs")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Mayuresh Chitale <[email protected]>
|
|
We should target to unify the code for different block devices in SPL to
reduce code size.
MMC, USB, SATA, and Semihosting use CONFIG_SPL_FS_LOAD_PAYLOAD_NAME to
indicate the filename to load.
NVMe uses CONFIG_SPL_PAYLOAD in spl_blk_load_image().
CONFIG_SPL_PAYLOAD is meant to define which binary to integrate into
u-boot-with-spl.bin. See commit
7550dbe38b3f ("spl: Add option SPL_PAYLOAD").
Change spl_blk_load_image() to use CONFIG_SPL_FS_LOAD_PAYLOAD_NAME.
Fixes: 8ce6a2e17577 ("spl: blk: Support loading images from fs")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Mayuresh Chitale <[email protected]>
|
|
Use config SPL_VIDEO_REMOVE to remove video driver at SPL stage before
jumping to next stage, in place of CONFIG_SPL_VIDEO, to allow user to
remove video if required.
Signed-off-by: Nikhil M Jain <[email protected]>
Reviewed-by: Devarsh Thakkar <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
At SPL stage when stack is relocated, the stack pointer needs to be
updated, the stack pointer may point to stack in on chip memory even
though stack is relocated.
Signed-off-by: Nikhil M Jain <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Update my and DPs email address to match current setup.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/aba5b19b9c5a95608829e86ad5cc4671c940f1bb.1688992543.git.michal.simek@amd.com
|
|
As implemented in the arch/arm/mach-rockchip/tpl.c file,
the CONFIG_TPL_BANNER_PRINT option will not work
if either of these options is not enabled.
Add dependency constraints to the CONFIG_TPL_BANNER_PRINT option
definition to prevent configuration problems
where option is enabled but do not take effect.
Suggested-by: Yanjie Ren <[email protected]>
Signed-off-by: Ying Sun <[email protected]>
|
|
Describe which numeric values can be used for as scratch options for
OpenSBI.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
|
|
Prepare v2023.07-rc6
|
|
Currently, spl_end points to the __bss_end address, which
is an external RAM address instead of the end of the SPL text
section in the internal RAM.
This causes boot failures on imx6-colibri, for example:
```
Trying to boot from MMC1
SPL: Image overlaps SPL
resetting ...
```
Fix this problem by assigning spl_end to _image_binary_end, as this
symbol properly represents the end of the SPL text section.
From u-boot-spl.map:
.end
*(.__end)
0x00000000009121a4 _image_binary_end = .
Fixes: 77aed22b48ab ("spl: spl_legacy: Add extra address checks")
Reported-by: Francesco Dolcini <[email protected]>
Signed-off-by: Fabio Estevam <[email protected]>
Tested-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Tested-by: Marek Vasut <[email protected]> # DH i.MX6Q DHCOM PDK2
|
|
The current mechanism is unnecessarily complex. Simplify the whole mechanism
such that the entire fitImage is signed, IVT is placed at the end, followed
by CSF, and this entire bundle is also authenticated. This makes the signing
scripting far simpler.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Check whether the loaded image or entry point does not overlap SPL.
Signed-off-by: Marek Vasut <[email protected]>
|
|
If only FIT images are enabled and loading the FIT image fails,
spl_nor_load_image() should return an error instead of zero.
Without this patch:
>>SPL: board_init_r()
spl_init
Trying to boot from NOR
Unsupported OS image.. Jumping nevertheless..
image entry point: 0x0
With patch:
>>SPL: board_init_r()
spl_init
Trying to boot from NOR
SPL: failed to boot from all boot devices (err=-6)
.### ERROR ### Please RESET the board ###
Signed-off-by: Mario Kicherer <[email protected]>
|
|
Add support to load the next stage image from an NVMe disk which may
be formatted as an EXT or FAT filesystem.
Signed-off-by: Mayuresh Chitale <[email protected]>
[trini: Drop hunk changing disk/part.c as that breaks other users]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add a generic API to support loading of SPL payload from any supported
filesystem on a given partition of a block device.
Signed-off-by: Mayuresh Chitale <[email protected]>
|
|
Add kconfig options to enable NVME and PCI NVMe support in SPL
Signed-off-by: Mayuresh Chitale <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Since commit 9905cae65e03 ("fs: ext4: check the minimal partition size
to mount"), a valid size needs to be provided when mounting
an ext filesystem. Fix the spl ext driver to use the parition size
instead of 0 when mounting the filesystem.
Signed-off-by: Mayuresh Chitale <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.10-rc1
global:
- Use proper U-Boot project name
Fix sparse warnings in zynqmp-clk, zynqmp handoff, board
cmd:
- Cover incorrect 0 length entries
Versal NET:
- Add bootmode logic
- Support SPP production version
- Add loadpdi command
ZynqMP:
- Clear pmufw node command ID handling
- Change power domain behavior around zynqmp_pmufw_node()
- Fix zynqmp cmd return values and pmufw command
- Fix R5 tcm init and modes
mmc:
- Sync Versal NET emmc DT binding
pcie:
- Add support for ZynqMP PCIe root port
video:
- Add support for ZynqMP DP
tools:
- Fix debug message in relocate-rela
|
|
Use proper project name in comments, Kconfig, readmes.
Reviewed-by: Neil Armstrong <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Qu Wenruo <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/0dbdf0432405c1c38ffca55703b6737a48219e79.1684307818.git.michal.simek@amd.com
|
|
Per the fit_conf_get_node() API doc, it returns configuration node
offset when found (>=0).
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_GADGET and related symbols. Fix typo and
rename SPL_USB_GADGET to "USB Gadget Support in SPL" .
Update the gadget Makefile to match the symbol changes.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_STORAGE and matching SYS_USB_FAT_BOOT_PARTITION .
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_HOST and updates help text of both USB_HOST
and SPL_USB_HOST .
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add method to remove video driver before loading u-boot proper. When
bootstage changes from SPL to u-boot proper, noo method is called to
remove video driver, and at u-boot proper if video driver is not
enabled, the video driver starts displaying garbage on the screen,
because there is no reserved space for video and the frame buffer gets
u-boot proper data written.
Signed-off-by: Nikhil M Jain <[email protected]>
|
|
Mask macro PART_ACCESS_MASK filter out access bits of emmc register and
macro EXT_CSD_EXTRACT_BOOT_PART() extracts boot part bits of emmc register.
So use EXT_CSD_EXTRACT_BOOT_PART() when extracting boot partition.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
On some platforms is SYS_MMCSD_FS_BOOT_PARTITION unsupported. So allow to
completely disable MMC FS Boot support via new option SYS_MMCSD_FS_BOOT.
By default MMC FS Boot support is enabled (like it was before) except for
ARCH_MVEBU where MMC FS Boot supported is unsupported due to Marvell
BootROM limitations.
Signed-off-by: Pali Rohár <[email protected]>
|
|
This was added by mistake and renders the function useless. Fix it.
Signed-off-by: Simon Glass <[email protected]>
Fixes: 33c60a38bb9 ("trace: Use notrace for short")
Reported-by: Stefan Herbrechtsmeier <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
In this case, using IS_ENABLED(...) to attempt to load the image results
in harder to read and less useful code, along with having to define a
CONFIG value that would be unused. To maintain the current albeit
slightly odd behavior, maintain that if we have both SPL_FS_FAT and
SPL_SATA_RAW_U_BOOT_USE_SECTOR enabled, we use SPL_FS_FAT for the load.
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
|
|
The attribute syntax is quite verbose. Use the macro provided for this
purpose.
Signed-off-by: Simon Glass <[email protected]>
|
|
Current default size of 0x100000 is not capable of getting the FIT
buffer during boot when transitioning to using binman generated boot
images for certain K3 devices, so increase it to 0x400000. Since A72 SPL
is coming after relocation to DDR this should not be an issue for any K3
device, so make it default for all.
Signed-off-by: Neha Malcom Francis <[email protected]>
Acked-by: Andrew Davis <[email protected]>
|
