| Age | Commit message (Collapse) | Author |
|---|
|
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <[email protected]>
Signed-off-by: Suniel Mahesh <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <[email protected]>
Signed-off-by: Suniel Mahesh <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Commit 65cc0e2a65d2 ("global: Move remaining CONFIG_SYS_* to CFG_SYS_*")
renamed CONFIG_SYS_UBOOT_START to CFG_SYS_UBOOT_START. Unfortunately,
this meant that the value was no longer available to the Makefile. This
caused imxrt to fail to boot. All the other boards that used this
variable were unaffected because they were using the default value
which is CONFIG_TEXT_BASE.
This commit converts CFG_SYS_UBOOT_START to Kconfig and sets the default
value to CONFIG_TEXT_BASE.
Suggested-by: Marek Vasut <[email protected]>
Suggested-by: Tom Rini <[email protected]>
Signed-off-by: Jesse Taube <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <[email protected]>
|
|
On x86 devices we use CAR (Cache-As-RAM) to hold the malloc() region in
SPL, since SDRAM is not set up yet. This means that driver model stores
its tables in this region.
When preparing to jump from SPL to U-Boot proper, we must disable CAR, so
that the CPU can uses the caches normally. This means that driver model
tables become inaccessible. From there until we jump to U-Boot proper, we
must avoid using driver model.
This is only a problem on boards which operate this way, for example
chromebook_link64
Add a flag to indicate that driver model is dead and should not be used.
It can be used in SPL to avoid hanging the machine.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This CONFIG is used but is not given a value by some boards. Use
a default value of 0 explicitly, rather than relying on the 0 value
provided by CONFIG_SPL_LOAD_FIT_ADDRESS
This will allow us to make SPL_LOAD_FIT_ADDRESS depend on SPL_LOAD_FIT
as it should.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This relates to booting, so move it there. Create a new Kconfig menu for
things related to devicetree fixup.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This relates to booting since it fixes up the devicetree for the OS. Move
it into the boot/ directory.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
These appear prominently in the main menu at present. Move them to the
video Kconfig where they belong.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This relates to graphics which is only active when CONFIG_VIDEO is
enabled. Move it into that directory.
For most boards there is no harm in compiling it always, since it if not
used it will be dropped by the linker. But for the EFI app this is not
the case, so retain use of the BMP Kconfig.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case anything errors out during the SDP transfer, detach
the controller instead of bailing out right away. This way,
the controller can be reattached on next attempt.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case anything errors out during the DFU registration, detach
the controller instead of bailing out right away. This way, the
controller can be reattached on next attempt.
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8f8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <[email protected]>
|
|
spl_blk_load_image() should not return an uninitialized value if
blk_get_devnum_by_uclass_id() fails.
Fixes: 8ce6a2e17577 ("spl: blk: Support loading images from fs")
Reported-by: Xavier Drudis Ferran <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Xavier Drudis Ferran <[email protected]>
|
|
spl_invoke_opensbi function is not returned to SPL. Thus, we need to
set __noreturn function attribute.
Signed-off-by: Chanho Park <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
To support SPL_SYS_MALLOC_CLEAR_ON_INIT, we have to modify
#ifdef CONFIG_SYS_MALLOC_CLEAR_ON_INIT
to #if CONFIG_IS_ENABLED(SYS_MALLOC_CLEAR_ON_INIT)
Signed-off-by: Bo Gan <[email protected]>
Signed-off-by: Shengyu Qu <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Prepare v2023.10-rc4
|
|
Add a new event which handles this function. Convert existing use of
the function to use the new event instead.
Make sure that EVENT is enabled by affected boards, by selecting it from
the LAST_STAGE_INIT option. For x86, enable it by default since all boards
need it.
For controlcenterdc, inline the get_tpm() function and make sure the event
is not built in SPL.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the misc_init_f event instead, which is designed for this purpose.
All boards with CONFIG_VID already enable CONFIG_EVENT.
Signed-off-by: Simon Glass <[email protected]>
|
|
Convert this to use events instead of calling a function directly in the
init sequence.
Rename it to arch_fsp_init_f() to distinguish it from the one that happens
after relocation.
For FSPv2 nothing needs to be done here, so drop the empty function.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move the manual-relocation code to the initcall file. Make sure to avoid
manually relocating event types. Only true function pointers should be
relocated.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present the initcall list consists of a list of function pointers. Over
time the initcall lists will likely change to mostly emitting events,
since most of the calls are board- or arch-specific.
As a first step, allow an initcall to be an event type instead of a
function pointer. Add the required macro and update initcall_run_list() to
emit an event in that case, or ignore it if events are not enabled.
The bottom 8 bits of the function pointer are used to hold the event type,
with the rest being all ones. This should avoid any collision, since
initcalls should not be above 0xffffff00 in memory.
Convert misc_init_f over to use this mechanism.
Add comments to the initcall header file while we are here. Also fix up
the trace test to handle the change.
Signed-off-by: Simon Glass <[email protected]>
|
|
Export this function so it can be used with initcall debugging.
Signed-off-by: Simon Glass <[email protected]>
|
|
Somehow I do not see any inlining with initcalls now. I was sure I saw
it when this commit went in, but now it seems to make things worse.
This reverts commit 47870afab92fca6e672c03d0dea802a55e200675.
Signed-off-by: Simon Glass <[email protected]>
|
|
The current event spy is always passed the event context and the event.
The context is always NULL for a static spy. The event is not often used.
Introduce a 'simple' spy which takes no arguments. This allows us to drop
the adaptation code that many of these spy records use.
Update the event script to find these in the image.
Signed-off-by: Simon Glass <[email protected]>
|
|
Fix the following warning produced on qemu-x86_64_defconfig:
"
common/bouncebuf.c: In function ‘bounce_buffer_stop’:
common/bouncebuf.c:82:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
82 | dma_unmap_single((dma_addr_t)state->bounce_buffer,
| ^
"
The warning is valid, the pointer has to be up-cast first.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Andrew Davis <[email protected]>
|
|
This patch introduces EVT_DM_POST_INIT_R event type for handling hooks
after relocation.
Fixes: 55171aedda88 ("dm: Emit the arch_cpu_init_dm() even only before relocation")
Suggested-by: Simon Glass <[email protected]>
Cc: Bin Meng <[email protected]>
Signed-off-by: Chanho Park <[email protected]>
Tested-by: Milan P. Stanić <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Roland Ruckerbauer <[email protected]>
Tested-by: Roland Ruckerbauer <[email protected]>
Fixed missing event name in event.c:
Signed-off-by: Simon Glass <[email protected]>
|
|
Prepare v2023.10-rc3
Signed-off-by: Tom Rini <[email protected]>
|
|
There is no requirement that a partition 1 exists in a partition table.
We should not try to retrieve information about it.
We should not even try reading with partition number
CONFIG_SYS_NVME_BOOT_PARTITION here as this is done in the fs_set_blk_dev()
call anyway.
Fixes: 8ce6a2e17577 ("spl: blk: Support loading images from fs")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
When Falcon Mode is enabled, SPL needs to check the value of
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR. Unfortunately, it was using the
CONFIG_VAL(SYS_MMCSD_RAW_MODE_ARGS_SECTOR) which converts it into
CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR when CONFIG_SPL_BUILD is
enabled. CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR does not exist in
common/spl/Kconfig. Replaced with
defined(CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR).
Signed-off-by: Elena Popa <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
board_get_usable_ram_top() returns a physical address that is stored in
gd->ram_top. The return type of the function should be phys_addr_t like the
current type of gd->ram_top.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Allow loading a FIT image via semihosting in SPL.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Add the actual support code for SPL_ZERO_MEM_BEFORE_USE and remove
existing Starfive JH7110's L2 LIM clean code, since existing code has
following issues:
1. Each hart (in the middle of a function call) overwriting its own
stack and other harts' stacks.
(data-race and data-corruption)
2. Lottery winner hart can be doing "board_init_f_init_reserve",
while other harts are in the middle of zeroing L2 LIM.
(data-race)
Signed-off-by: Bo Gan <[email protected]>
Signed-off-by: Shengyu Qu <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
At present this feature is enabled in SPL if a bloblist is available.
Some platforms may not want to use this, so add an option to allow the
feature to be disabled.
Note that the feature unfortunately only fills in part of the
video-handoff information, so causes failures on x86 platforms. For now,
disable it there.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Tested-by: Bin Meng <[email protected]> # qemu-x86_64
|
|
This name is a little confusing since it suggests that it sets up the
sibling block device. In fact it sets up a bootdev for it. Rename the
function to make this clearer.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
Now all linker symbols are declared as type char[]. Though we can
reference the address via both the array name 'var' and its address
'&var'. It's better to unify them to avoid confusing developers.
This patch converts all '&var' linker symbol refrences to the most
commonly used format 'var'.
Signed-off-by: Shiji Yang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Some coding convention fixes for print_resetinfo().
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Fixes: 3db711085752 ("crc32: Use the crc.h header for crc functions")
Signed-off-by: Ilya Lukin <[email protected]>
|
|
Drop duplicate space in Kconfig symbol description.
Signed-off-by: Marek Vasut <[email protected]>
|
