| Age | Commit message (Collapse) | Author |
|---|
|
This adds a boot method for loading the next stage from the host. It is
mostly modeled off of spl_load_image_ext. I am not really sure why/how
spl_load_image_fat uses three different methods to load the image, but
the simple case seems to work OK for now.
To control the presence of this boot method, we add a config symbol.
While we're at it, we update the original semihosting config symbol.
I think semihosting has some advantages of other forms of JTAG boot.
Common other ways to boot from JTAG include:
- Implementing DDR initialization through JTAG (typically with dozens of
lines of TCL) and then loading U-Boot. The DDR initialization
typically uses hard-coded register writes, and is not easily adapted
to different boards. BOOT_DEVICE_SMH allows booting with SPL,
leveraging U-Boot's existing DDR initialization code. This is the
method used by NXP's CodeWarrior IDE on Layerscape processors (see
AN12270).
- Loading a bootloader into SDRAM, waiting for it to initialize DDR, and
then loading U-Boot. This is tricky, because the debugger must stop the
boot after the bootloader has completed its work. Trying to load
U-Boot too early can cause failure to boot. This is the method used by
Xilinx with its Zynq(MP) processors.
- Loading SPL with BOOT_DEVICE_RAM and breaking before SPL loads the
image to load U-Boot at the appropriate place. This can be a bit
tricky, because the load address is dependent on the header size. An
elf with symbols must also be used in order to stop at the appropriate
point. BOOT_DEVICE_SMH can be viewed as an extension of this process,
where SPL automatically stops and tells the host where to place the
image.
Signed-off-by: Sean Anderson <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CLOCKS
Signed-off-by: Tom Rini <[email protected]>
|
|
Add the support of image pre load in spl or tpl
when loading an image from ram.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Philippe Reynes <[email protected]>
|
|
This is not defined by any board. Even sandbox doesn't actually use
it since it has migrated to DM_VIDEO.
Drop this option. Remove the dead code also, for completeness, even
though the whole lcd.c file will be dropped soon.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Jason Liu <[email protected]>
|
|
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_PHY_RESET_DELAY
Cc: Ramon Fried <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_RESET_PHY_R
Cc: Ramon Fried <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Fix the help which should refer to TPL, not SPL.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Alper Nebi Yasak <[email protected]>
Suggested-by: Alper Nebi Yasak <[email protected]>
|
|
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <[email protected]>
|
|
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <[email protected]>
|
|
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <[email protected]>
|
|
Call event_init() before relocation to get the event system running.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a way to create and dispatch events without needing to allocate
memory. Also add a way to 'spy' on events, thus allowing 'hooks' to be
created.
Use a linker list for static events, which we can use to replace functions
like arch_cpu_init_f(). Allow an EVENT_DEBUG option which makes it
easier to see what is going on at runtime, but uses more code space.
Dynamic events allow the creation of a spy at runtime. This is not always
necessary, but can be enabled with EVENT_DYNAMIC if needed.
A 'test' event is the only option for now.
Signed-off-by: Simon Glass <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_POSTCLK_INIT
Signed-off-by: Tom Rini <[email protected]>
|
|
When CONFIG_SPL_FIT is enabled we do not access U-Boot directly in
the image, since it is embedded in a FIT which is parsed at runtime.
Provide a CONFIG option to drop the symbols in this case.
Signed-off-by: Simon Glass <[email protected]>
|
|
These symbols are incorrect, meaning that binman cannot find the
associated entry. This leads to errors like:
binman: Section '/binman/simple-bin': Symbol '_binman_spl_prop_size'
in entry '/binman/simple-bin/u-boot-spl/u-boot-spl-nodtb':
Entry 'spl' not found in list (mkimage,u-boot-spl-nodtb,
u-boot-spl-bss-pad,u-boot-spl-dtb,u-boot-spl,u-boot-img,main-section)
Fix it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Replace %zx by %lx and cast size_t to ulong.
U-Boot currently prints garbage debug output:
size=x, ptr=18, limit=18: 4002a000
With this change it prints correct debug data:
size=18, ptr=18, limit=2000: 4002a000
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
fdt_fixup_mtdparts()
Listing MTD partitions directly in the flash mode has been deprecated
for a while for kernel Device Trees. Look for a node "partitions" in the
found flash nodes and use it instead of the flash node itself for the
partition list when it exists, so Device Trees following the current
best practices can be fixed up.
Signed-off-by: Matthias Schiffer <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Using the XHCI driver, the function `usb_kbd_poll_for_event` takes
30-40ms to run. The exact time is dependent on the polling interval the
keyboard requests in its descriptor, and likely cannot be significantly
reduced without major rework to the XHCI driver.
The U-Boot EFI console service sets a timer to poll the keyboard every 5
microseconds, and this timer is checked every time a block is read off
disk. The net effect is that, on my system, loading a ~40MiB kernel and
initrd takes about 62 seconds with a slower keyboard and 53 seconds
with a faster one, with the vast majority of the time spent polling the
keyboard.
To solve this problem, this patch adds a 20ms delay between consecutive
calls to `usb_kbd_poll_for_event`. This is sufficient to reduce the
total loading time to under half a second for both keyboards, and does
not impact the perceived keystroke latency.
Signed-off-by: Thomas Watson <[email protected]>
|
|
Use the new IF_ENABLED_INT() feature to avoid needing our own inline
function to handle this case. Tidy up the logic to ensure that the value
is only used when present. Update the 'expected' comment also.
Signed-off-by: Simon Glass <[email protected]>
|
|
ymodem_read_fit() driver will end copying up to BUF_SIZE boundary even
when requested size of copy operation is less than that.
For example, if offset = 0, size = 1440B, ymodem_read_fit() ends up
copying 2KB from offset = 0, to destination buffer addr
This causes data corruption when malloc'd buffer is passed during UART
boot since commit 03f1f78a9b44 ("spl: fit: Prefer a malloc()'d buffer
for loading images")
With this, UART boot works again on K3 (AM654, J7, AM64) family of
devices.
Fixes: 03f1f78a9b44 ("spl: fit: Prefer a malloc()'d buffer for loading images")
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Currently the names MMC1, MMC2 and MMC2_2 are output in the SPL. To
achieve more userbility here the name of the boot source can be returned.
E.g. for "MMC1" -> "eMMC" or "MMC2" -> "SD card".
Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
Tested-by: Michael Walle <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
|
|
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <[email protected]>
|
|
At present we rely on the key blob being in the global_data fdt_blob
pointer. This is true in U-Boot but not with tools. For clarity, pass the
parameter around.
Signed-off-by: Simon Glass <[email protected]>
|
|
Replace CONFIG_SYS_MAX_FLASH_BANKS by CFI_FLASH_BANKS to prepare
Kconfig migration and avoid to redefine CONFIG_SYS_MAX_FLASH_BANKS
in cfi_flash.h.
After this patch CONFIG_SYS_MAX_FLASH_BANKS should be never used in
the cfi code: use CFI_MAX_FLASH_BANKS for struct size or CFI_FLASH_BANKS
for number of CFI banks which can be dynamic.
This patch modify all the files which include mtd/cfi_flash.h.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <[email protected]>
|
|
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
|
|
Commit 9baab60b8054 ("SPL: Add support for parsing board / BootROM specific
image types") added support for loading board specific image types.
This commit adds support for a new weak function spl_parse_board_header()
which is called after loading boot image. Board may implement this function
for checking if loaded board specific image is valid.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Sphinx expects Return: and not @return to indicate a return value.
find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Drop the remaining ifdefs around header includes, to fix an old TODO.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Ovidiu Panait <[email protected]>
|
|
Not all architectures define <asm/gpio.h> and even on those that do, the
header cannot be included for all boards without causing various build
failures.
Since common/board_r.c only needs gpio_hog_probe_all() declaration, include
<asm-generic/gpio.h> and drop the associated ifdef.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Ovidiu Panait <[email protected]>
|
|
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Ovidiu Panait <[email protected]>
|
|
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Reviewed-by: Matthias Brugger <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Ovidiu Panait <[email protected]>
|
|
Add a return value to kgdb_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub. Also, move the "KGDB"
print message inside kgdb_init().
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Ovidiu Panait <[email protected]>
|
|
Commit 98f705c9cefd ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <[email protected]>
Reviewed-by: Thomas Huth <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Ovidiu Panait <[email protected]>
|
|
This implementation is intended to be copied to other projects and
modified, to as to foster a standard means of communcating runtime
information between firmware projects.
The GPL-2 license is too restrictive for some projects, e.g. those
intended as reference implementations rather than designed for
collaborative open-source development.
Update the license to make this easier to share.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a few convenience functions to obtain useful information about the
bloblist.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present we do support allocating the bloblist but the Kconfig is a bit
strange, since we still have to specify an address in that case. Partly
this is because it is a pain to have CONFIG options that disappears when
its dependency is enabled. It means that we must have #ifdefs in the code,
either in the C code or header file.
Make use of IF_ENABLED_INT() and its friend to solve that problem, so we
can separate out the location of bloblist into a choice. Put the address
and size into variables so we can log the result.
Add the options for SPL as well, so we can use CONFIG_IS_ENABLED().
Signed-off-by: Simon Glass <[email protected]>
|
|
We typically refer to the different U-Boot builds that a board runs
through as phases. This avoids confusion with the word 'stage' which is
used with bootstage, for example. Fix up some bloblist Kconfig help
which uses the wrong term.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the convenience functions to improve readability.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present if someone adds a tag in the middle of the list it works well
enough within a U-Boot build. But if these tags are used in another
project, or with an older version of SPL, the numbers make become
inconsistent.
Use explicit tag numbers that never change, to resolve this problem.
Allocate areas for existing U-Boot tags and set up an area for use by
projects and vendors, as well as for private use. Keep tags above
0x10000 unallocated for now.
Update bloblist_tag_name() and the tests to work with this new setup.
Signed-off-by: Simon Glass <[email protected]>
|
|
The EC event log tag is no-longer used. The vboot handoff is now handled
by the vboot context instead.
Drop these unused tags.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a U_BOOT prefix to this tag since it is specific to the U-Boot
project.
Signed-off-by: Simon Glass <[email protected]>
|
|
|
