| Age | Commit message (Collapse) | Author |
|---|
|
So we can use it for falcon mode as well.
Signed-off-by: Peter Korsgaard <[email protected]>
|
|
So we can instead fallback to doing something else on errors.
Signed-off-by: Peter Korsgaard <[email protected]>
|
|
|
|
simple-framebuffer is a new device tree binding that describes a pre-
configured frame-buffer memory region and its format. The Linux kernel
contains a driver that supports this binding. Implement functions to
create a DT node (or fill in an existing node) with parameters that
describe the framebuffer format that U-Boot is using.
This will be immediately used by the Raspberry Pi board in U-Boot, and
likely will be used by the Samsung ARM ChromeBook support soon too. It
could well be used by many other boards (e.g. Tegra boards with built-in
LCD panels, which aren't yet supported by the Linux kernel).
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This can be useful to force bootcmd to execute as soon as U-Boot has
started.
My use-case is: An SoC-specific tool pushes U-Boot into RAM, along with
an image to be written to device boot flash, with the DT config property
"bootcmd" set to contain a command to write that image to flash. In this
scenario, we don't want to allow any stale bootdelay value taken from
the current flash content to affect how long it takes before the
flashing process starts.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Acked-by: Gerald Van Baren <[email protected]>
|
|
The generic-board board_init_f function called board_postclk_init twice.
The first one came from arch/arm/lib/board.c, while the second one
from arch/powerpc/lib/board.c.
This commit deletes the first occurrence.
In addition, the second get_clocks call is moved after
board_postclk_init in order to keep the function call order
both for ARM and PowerPC.
ARM board calles get_clocks function after board_postclk_init.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Use map_sysmem() to convert from address to pointer, so that sandbox can
print FIT information without crashing.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new common code to load a kernel. The functionality should not
change.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use map_sysmem() when converting from addresses to pointers, so that
bootm can be used with sandbox.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new common code to load a flat device tree. Also fix up a few casts
so that this code works with sandbox. Other than that the functionality
should not change.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new common code to load a ramdisk. The functionality should not
change.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present code to load an image from a FIT is duplicated in the three
places where it is needed (kernel, fdt, ramdisk).
The differences between these different code copies is fairly minor.
Create a new function in the fit code which can handle any of the
requirements of those cases.
Signed-off-by: Simon Glass <[email protected]>
|
|
Define a simple debug condition at the top of the file, to avoid using
lots of #ifdefs later on.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
Define a simple debug condition at the top of the file, to avoid using
lots of #ifdefs later on.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
The headers are a bit out of order, so fix them.
Signed-off-by: Simon Glass <[email protected]>
|
|
There are a few over-long lines and other checkpatch problems in this area
of the code. Prepare the ground for the next patch by tidying these up.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
These functions are now available, so use them to avoid extra code here.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
Move this code into its own function, since it clutters up main_loop().
Signed-off-by: Simon Glass <[email protected]>
|
|
There are two implementations of abortboot(). Turn these into two separate
functions, and create a single abortboot() which calls either one or the
other.
Also it seems that nothing uses abortboot() outside main, so make it static.
At this point there is no further use of CONFIG_MENU in main.c.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
This function should be declared in net.h.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
This patch adds a print messages while using 'sf read' and
'sf write' commands to make sure that how many bytes read/written
from/into flash device.
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
This patch adds a print messages while using 'sf erase' command
to make sure that how many bytes erased in flash device.
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
|
|
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <[email protected]>
[[email protected]: some eccstrength and build fixes]
Signed-off-by: Scott Wood <[email protected]>
|
|
Conflicts:
common/cmd_fpga.c
drivers/usb/host/ohci-at91.c
|
|
Add board detail function to print more individual board information.
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
|
|
The "cp" command has not worked since
commit 0628ab8ec59834f98ede267edd21ddb8ba0bb57b,
because of the following lines, which set the destination
and the source to the same address.
buf = map_sysmem(addr, bytes);
src = map_sysmem(addr, bytes);
Tested-by: Tom Rini <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Adjust the sizes calculated for whole partition/chip operations by
removing the size of bad blocks so we don't try to erase/read/write
past a partition/chip boundary.
Signed-off-by: Harvey Chapman <[email protected]>
|
|
It appears that there are some cases where we have more than 4 banks
of memory. Use CONFIG_NR_DRAM_BANKS if it's defined to handle this.
This will take up a little extra stack space (64 bytes extra if we go
up to 8 banks), but that seems OK.
Signed-off-by: Doug Anderson <[email protected]>
|
|
This makes fixup_silent_linux() use malloc() to allocate its
working space, meaning that our maximum kernel command line
should only be limited by malloc(). Previously it was silently
overflowing the stack.
Note that nothing about this change increases the kernel's maximum
command line length. If you have a command line that is >256
bytes it's up to you to make sure that kernel can handle it.
Signed-off-by: Doug Anderson <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Andy Fleming <[email protected]>
|
|
The mpc85xx repuires a special layout on the memory device that is
connected to the eSDHC controller interface. But the file spl_mmc.c
didn't handle this specfic case, there needs a special treatmen, in
the powerpc drictory. So, there is no longer to keep spl_mmc.c on
mpc85xx, CONFIG_SPL_FRAMEWORK is not set.
When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not
set, there was an error in drivers/mmc/spl_mmc.c:
drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'.
Now, the solution is to move the file "spl_mmc.c" to directory "common/spl".
Signed-off-by: Ying Zhang <[email protected]>
|
|
With fewer #ifdefs the code is more readable and more of the code is
compiled for all boards. Add defines in the header file to control
what features are enabled, and then use if() instead of #ifdef.
Signed-off-by: Simon Glass <[email protected]>
|
|
This seems to be a common function for several architectures, so create
a common function rather than duplicating the code in each arch.
Also make an attempt to avoid introducing #ifdefs in the new code, partly
by removing useless #ifdefs around function declarations in the image.h
header.
Signed-off-by: Simon Glass <[email protected]>
|
|
The image file is still very large, and some of the code is only used when
libfdt is in use. Move this code into a new file.
Signed-off-by: Simon Glass <[email protected]>
|
|
This code is very large, and in SPL it isn't always useful to print
out image information (in fact there might not even be a console
active). So disable this feature unless this option is set.
Signed-off-by: Simon Glass <[email protected]>
|
|
There are only two left. One is unnecessary and the other can be moved
to the header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
Much of the image code uses addresses as ulongs and pointers interchangeably,
casting between the two forms as needed.
This doesn't work with sandbox, which has a U-Boot RAM buffer which is
separate from the host machine's memory.
Adjust the cost so that translating from a U-Boot address to a pointer uses
map_sysmem(). This allows bootm to work correctly on sandbox.
Note that there are no exhaustive tests for this code on sandbox, so it is
possible that some dark corners remain.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]> (v1)
|
|
This function will be used to print signatures as well as hashes, so rename
it. Also make it static since it is not used outside this file.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This function will be needed by signature checking code, so export it,
and also add docs.
Signed-off-by: Simon Glass <[email protected]>
|
|
The string " error\n" appears in each error string. Move it out to a
common place.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The existing function is long and most of the code is indented a long
way. Before adding yet more code, split this out into its own function.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]> (v1)
|
|
This is the main entry point to the FIT image verification code. We will
be using it to handle image verification with signatures, so rename the
function.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This code is never compiled into U-Boot, so move it into a separate
file in tools/ to avoid the large #ifdef.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The FIT code is about half the size of the >3000-line image.c. Split this
code into its own file.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
One we split out the FIT code from image.c we will need this function.
Export it in the header.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Rather than repeat the line
#if defined(CONFIG_TIMESTAMP) || defined(CONFIG_CMD_DATE) || \
defined(USE_HOSTCC)
everywhere, put this in a header file and #define IMAGE_ENABLE_TIMESTAMP
to either 1 or 0. Then we can use a plain if() in most code and avoid
the #ifdefs.
The compiler's dead code elimination ensures that the result is the same.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Rather than needing to call one of many hashing algorithms in U-Boot,
provide a function hash_block() which handles this, and can support all
available hash algorithms.
Once we have md5 supported within hashing, we can use this function in
the FIT image code.
Signed-off-by: Simon Glass <[email protected]>
|
|
This should say 'environmnent'.
Signed-off-by: Simon Glass <[email protected]>
|
|
powerpc-eldk53-warning-fixes
|
