| Age | Commit message (Collapse) | Author |
|---|
|
If one command fails, 'run' command should terminate and not execute
any remaining variables.
Signed-off-by: Timo Ketola <[email protected]>
Tested-by: Wolfgang Denk <[email protected]>
Tested-by: Simon Glass <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
The standalone example does not have get_timer() defined, so we cannot
rely on it being available.
Move the timer function into boootstage.c to avoid this problem.
This corrects a build breakage for the standalone example on some boards.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Matthias Fuchs <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Mike Frysinger <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Tom Warren <[email protected]>
Cc: Graeme Russ <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
SPI flash operations inadvertently stretching beyond the flash size will
result in a wraparound. This may be particularly dangerous when burning
u-boot, because the flash contents will be corrupted rendering the board
unusable, without any warning being issued.
So add a consistency checking so not to overflow past the flash size.
Signed-off-by: Gerlando Falauto <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
image.c: In function ‘boot_get_ramdisk’:
image.c:800:8: warning: unused variable ‘end’ [-Wunused-variable]
Signed-off-by: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
This patch allows loading RAW ramdisk via bootz command. The raw ramdisk is
loaded only in case it's size is specified:
bootz <kernel addr> <ramdisk addr>:<ramdisk size> <fdt addr>
For example:
bootz 0x42000000 0x43000000:0x12345 0x44000000
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Rob Herring <[email protected]>
Cc: Tom Warren <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: Simon Glass <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Nicolas Pitre <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Detlev Zundel <[email protected]>
|
|
This command boots Linux zImage from where the zImage is loaded to. Passing
initrd and fdt is supported.
Tested on i.MX28 based DENX M28EVK
Tested on PXA270 based Voipac PXA270.
NOTE: This currently only supports ARM, but other architectures can be easily
added by defining bootz_setup().
Signed-off-by: Marek Vasut <[email protected]>
Cc: Tom Warren <[email protected]>
Cc: [email protected]
Cc: [email protected],
Cc: Simon Glass <[email protected]>,
Cc: Stephen Warren <[email protected]>
Cc: Nicolas Pitre <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Detlev Zundel <[email protected]>
|
|
The following must be defined:
CONFIG_ENV_IS_IN_FAT
Enable this saving environment to FAT.
FAT_ENV_INTERFACE
Interface the FAT resides on (e.g. mmc).
FAT_ENV_DEVICE
The interface device number (e.g. 0 for mmc0)
FAT_ENV_PART
The device part (e.g. 1 for mmc0:1)
FAT_ENV_FILE
The filename of the environment file.
Author: Maximilian Schwerin <[email protected]>
Removed dead DEBUG comment.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
print in the "log info" command, if "log_version = 2" also the
value from "log->v2.con".
Signed-off-by: Heiko Schocher <[email protected]>
Acked-by: Detlev Zundel <[email protected]>
|
|
Signed-off-by: Heiko Schocher <[email protected]>
Acked-by: Detlev Zundel <[email protected]>
|
|
If the logbuffer contains LOGBUFF_LEN chars, they never got
printed with the "log show" command, because chars get
printed with the following for loop:
for (i = 0; i < (size & LOGBUFF_MASK); i++) {
with size = LOGBUFF_LEN and LOGBUFF_MASK = (LOGBUFF_LEN-1)
for loop never executed ...
Fix this.
Signed-off-by: Heiko Schocher <[email protected]>
Acked-by: Detlev Zundel <[email protected]>
Fixed merge conflict.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
* '[email protected]' of git://git.denx.de/u-boot-staging:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
|
|
This adds a spl command to the u-boot.
Related config:
CONFIG_CMD_SPL
activate/deactivate the command
CONFIG_CMD_SPL_NAND_OFS
Offset in NAND to use
Signed-off-by: Simon Schwarz <[email protected]>
Signed-off-by: Stefano Babic <[email protected]>
CC: Tom Rini <[email protected]>
CC: Wolfgang Denk <[email protected]>
|
|
Without this patch, some versions of gcc (at least ELDK 4.2) complain
about dereferencing type-punned pointers.
Reported-by: Marek Vasut <[email protected]>
Signed-off-by: Jason Hobbs <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Marek Vasut <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
|
|
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.
Signed-off-by: Matt Porter <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Once CONFIG_FAT_WRITE is defined, users can invoke 'fatwrite' command
that saves data in RAM as a FAT file.
This patch was originally part of
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/121847
Signed-off-by: Donggeun Kim <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Signed-off-by: Maximilian Schwerin <[email protected]>
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
This reverts commit 295d3942b806552503243f5cfb36aec6f1b5a9bf.
It turns that this really doesn't work very nicely. Instead we should
have a pre-console panic function so that we know that further execution
is impossible and we don't need to worry about trampling on UARTs, etc.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This inserts bootstage calls into tftp, usb start and bootm. We
could go further, but this is a reasonable start to illustrate
the concept.
Signed-off-by: Simon Glass <[email protected]>
|
|
This defines the basics of a new boot time measurement feature. This allows
logging of very accurate time measurements as the boot proceeds, by using
an available microsecond counter.
To enable the feature, define CONFIG_BOOTSTAGE in your board config file.
Also available is CONFIG_BOOTSTAGE_REPORT which will cause a report to be
printed just before handing off to the OS.
Most IDs are not named at this stage. For that I would first like to
renumber them all.
Timer summary in microseconds:
Mark Elapsed Stage
0 0 reset
205,000 205,000 board_init_f
6,053,000 5,848,000 bootm_start
6,053,000 0 id=1
6,058,000 5,000 id=101
6,058,000 0 id=100
6,061,000 3,000 id=103
6,064,000 3,000 id=104
6,093,000 29,000 id=107
6,093,000 0 id=106
6,093,000 0 id=105
6,093,000 0 id=108
7,089,000 996,000 id=7
7,089,000 0 id=15
7,089,000 0 id=8
7,097,000 8,000 start_kernel
Signed-off-by: Simon Glass <[email protected]>
|
|
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <[email protected]>
|
|
This changes over all the FIT image progress numbers to use enums
from bootstage.h.
Signed-off-by: Simon Glass <[email protected]>
|
|
This changes over the network-related progress numbers to use enums
from bootstage.h.
Signed-off-by: Simon Glass <[email protected]>
|
|
This changes over the NAND progress numbers to use enums from
bootstage.h.
Signed-off-by: Simon Glass <[email protected]>
|
|
This changes over the IDE progress numbers to use enums from bootstage.h.
Signed-off-by: Simon Glass <[email protected]>
|
|
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
Signed-off-by: Simon Glass <[email protected]>
|
|
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
This patch clear and disable the data cache for vxWorks.
The entry point sysInit(int) intended by Windriver to be called from
the vxWorks bootrom, a very small vxWorks system.
The routine is called by the go() handler in the bootrom, that clears
the cache from start of image to end of usable memory.
The PowerPC implementations only invalidates and disable the cache,
the ARM implementations also flush it.
U-Boot will be on the safe side, if it disables the data cache before
calling vxWorks sysInit(int).
Signed-off-by: Reinhard Arlt <[email protected]>
|
|
boot_get_fdt() expects a uImage-wrapped FDT to be loaded to a staging
location, and then memmove()s it to the load address specified in the
header. This change enhances boot_get_fdt() to detect when the image has
already been loaded to the correct address, and skip this memmove(). The
detection algorithm was written to match the equivalent for the kernel;
see bootm_load_os()'s IH_COMP_NONE case.
v2: New patch
Signed-off-by: Stephen Warren <[email protected]>
|
|
flush_dcache()/flush_icache() aren't defined in common.h,
flush_dcache_all()/invalidate_icache_all() however are.
Let the icache and dcache commands use those instead.
Signed-off-by: Stefan Kristiansson <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <[email protected]>
|
|
We currently have the same code in hush.c and main.c. This brings the
code into one place.
As an added feature, if the command function returns CMD_RET_USAGE then
cmd_process() will print a usage message for the command before
returning the standard failure code of 1.
ARM code size increases about 32 bytes with this clean-up.
Signed-off-by: Simon Glass <[email protected]>
|
|
There is a nasty interleave of #ifdefs in hush.c where the two code
paths have different indents. Remove this ickiness.
Signed-off-by: Simon Glass <[email protected]>
|
|
We should aim for a single point of entry to the commands, whichever
parser is used.
Signed-off-by: Simon Glass <[email protected]>
|
|
This saves about 1KB of code space on ARM with CONFIG_SYS_HUSH_PARSER
defined.
Signed-off-by: Simon Glass <[email protected]>
|
|
Boards can select either the 'built-in' parser or the hush parser. We
should not call builtin_run_command() if we are using the hush parser.
We use run_command() instead, since it knows how to call the correct
parser.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
This is a more sensible name, so rename it.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
The current run_command() is only one of the parsing options - the other
is hush. We should not call run_command() when the hush parser is being
used. So we rename this function to better explain its purpose.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
It really isn't clear why this is here and there is no comment, so
drop it.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
Following the corresponding Linux code, this patch relaxes reset timings
waiting at least 100ms after power to the ports. There are some reports
that it helps make enumeration work better on some high speed devices.
Furthermore, the wait is only done once after power has been enabled
on all ports.
CC: Remy Bohmer <[email protected]>
CC: Vincent Palatin <[email protected]>
Signed-off-by: Wolfgang Grandegger <[email protected]>
|
|
This moves keyboard polling logic from USB HCD drivers into USB
keyboard driver. Remove usb_event_poll() as keyboard polling was
the only user of this API. With this patch USB keyboard works with
EHCI controllers again. Tested on a tegra2 seaboard.
Signed-off-by: Allen Martin <[email protected]>
|
|
If CONSOLE_MUX is enabled, reevaluate console stdin when USB keyboard
device is detected.
Signed-off-by: Allen Martin <[email protected]>
|
|
When keys are pressed on the numeric keypad, emit key codes for the numbers,
operators, dot and enter.
Signed-off-by: Vincent Palatin <[email protected]>
|
|
When doing a "GET_REPORT" request on the keyboard control endpoint,
the report ID should 0 (ie report ID not used) rather than 1
as reports are not used in boot mode.
Signed-off-by: Vincent Palatin <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
Cc: Remy Bohmer <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
Cc: Remy Bohmer <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
Cc: Remy Bohmer <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
* 'master' of git://git.denx.de/u-boot-nand-flash:
cmd_nand.c: Fix 'nand dump' after latest MTD resync
mtd/nand:Fix wrong usage of is_blank() in fsl_ifc_run_command
mtd/nand: Fix IFC driver to support 2K NAND page
nand: reinstate lazy bad block scanning
Revert "nand: make 1-bit software ECC configurable"
|
