| Age | Commit message (Collapse) | Author |
|---|
|
Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: Mario Six <[email protected]>
|
|
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six <[email protected]>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini <[email protected]>
|
|
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MXC_GPIO
Signed-off-by: Adam Ford <[email protected]>
|
|
When CONFIG_DM_MMC=y, CONFIG_BLK should be selected, otherwise the
SD/eMMC card cannot be used.
Also, select CONFIG_DM_USB=y when CONFIG_USB=y to avoid build failure.
Tested on mx6slevk, mx7dsabresd and mx6ullevk.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Tested-by: Adam Ford <[email protected]>
Tested-by: Sébastien Szymanski <[email protected]>
Tested-by: Jagan Teki <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
The option is specified in Kconfig, but still a few config header files
are overriding the choice by #undef'ing it. Re-sync the option with
moveconfig to rid of the #undefs.
Signed-off-by: Tuomas Tynkkynen <[email protected]>
|
|
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that the driver supports it, move these boards over to use driver
model fully for MMC.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Enable MMC support.
The fsl sdhc driver needs regulator to enable power, so enable
regulator support.
And bootcmd and more env.
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add EVK board support.
Add the evk dts file.
LOG:
U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800)
CPU: Freescale i.MX7ULP rev1.0 at 500 MHz
Reset cause: POR
Boot mode: Dual boot
Model: NXP i.MX7ULP EVK
DRAM: 1 GiB
MMC: FSL_SDHC: 0
In: serial@402D0000
Out: serial@402D0000
Err: serial@402D0000
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
