summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2023-11-12arm: dts: icnova-a20-adb4006: Add board supportLudwig Kormann
Add board support for ICnova A20 SomPi compute module on ICnova ADB4006 development board. Specification: SoM - Processor: Allwinner A20 Cortex-A7 Dual Core at 1GHz - 512MB DDR3 RAM - Fast Ethernet (Phy: Realtek RTL8201CP) ADB4006 - I2C - 2x USB 2.0 - 1x Fast Ethernet port - 1x SATA - 2x buttons (PWRON, Boot) - 2x LEDS - serial console - HDMI - µSD-Card slot - Audio Line-In / Line-Out - GPIO pinheaders https://wiki.in-circuit.de/index.php5?title=ICnova_ADB4006 https://wiki.in-circuit.de/index.php5?title=ICnova_A20_SODIMM devicetree upstreamed with linux 6.5 Signed-off-by: Ludwig Kormann <[email protected]> Reviewed-by: Andre Przywara <[email protected]>
2023-11-10Merge tag 'u-boot-stm32-20231110' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-stm _ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled _ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM _ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM _ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM _ Read auth stats and boot_partition from tamp
2023-11-10rockchip: ringneck-px30: enable SPL_BOARD_INITQuentin Schulz
Now that Ringneck requires some board-specific code (namely resetting the MCU companion controller) to be run during SPL stage, let's enable SPL_BOARD_INIT. Cc: Quentin Schulz <[email protected]> Reviewed-by: Heiko Stuebner <[email protected]> Signed-off-by: Quentin Schulz <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-11-10arm: stm32: Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOMMarek Vasut
The maximum size of u-boot.itb in SPI NOR on DH STM32MP15 DHSOM is 0x160000 . Define this size in U-Boot config to prevent misconfigured builds from emitting larger u-boot.itb than the one which fits the SPI NOR area reserved for the blob. The SPI NOR layout is as follows: 0x00_0000..0x03_ffff ... SPL 1 0x04_0000..0x07_ffff ... SPL 2 0x08_0000..0x1d_ffff ... U-Boot 0x1e_0000..0x1e_ffff ... Environment 1 0x1f_0000..0x1f_ffff ... Environment 2 Signed-off-by: Marek Vasut <[email protected]> Reviewed-by: Patrice Chotard <[email protected]>
2023-11-10arm: stm32: Enable TCP, IPv6, wget on DH STM32MP15 DHSOMMarek Vasut
Enable support for TCP protocol, wget, and IPv6 on this platform. The former two allow users download payload into the U-Boot from a web server, which may be more convenient or easier to set up than TFTP server. The later is enabled to future proof the IP stack on this platform. Signed-off-by: Marek Vasut <[email protected]> Reviewed-by: Patrice Chotard <[email protected]>
2023-11-09rockchip: ringneck-px30: enable i2c commandQuentin Schulz
This is a useful tool to check the presence of a device on a specific i2c bus, so let's enable it. Cc: Quentin Schulz <[email protected]> Signed-off-by: Quentin Schulz <[email protected]> Reviewed-by: Heiko Stuebner <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-11-09board: rockchip: add Pine64 QuartzPro64 RK3588 boardTom Fitzhenry
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64. UART and boot over SD/eMMC/RJ45 are tested to work. Linux commits from next-20231013: 8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree") Signed-off-by: Tom Fitzhenry <[email protected]> Reviewed-by: Kever Yang <[email protected]> Cc: Eugen Hristev <[email protected]> Cc: Jonas Karlman <[email protected]> Cc: Ondrej Jirman <[email protected]>
2023-11-07xilinx: Enable SPI_FLASH_MTD by defaultMichal Simek
Provide access to qspi flash layout via mtd command. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/b3c4a3eddb71aab9535b034380d0dbae770828d4.1698837725.git.michal.simek@amd.com
2023-11-07xilinx: versal: Setup 30MHz as default spi frequencyMichal Simek
Align default SPI configuration with ZynqMP/Versal NET. There is no reason to run on lower frequencies. Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/c1d6ebd659f3002649b1200c926f8b9ed3132085.1698749448.git.michal.simek@amd.com
2023-11-07arm64: versal-net: enable CONFIG_MMC_SDHCI_ADMAVenkatesh Yadav Abbarapu
The Standard Host Controller Interface (SDHCI) specification version 3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit widths of DMA. This significantly improves read and write throughput. Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]>
2023-11-07ARM: zynq: Disable the config CONFIG_SPI_FLASH_USE_4K_SECTORSVenkatesh Yadav Abbarapu
Lock size for the flashes will be in terms of sector size, so disable the CONFIG_SPI_FLASH_USE_4K_SECTORS and read it from the flash itself. Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/8e5c2bf3b7e5f366c4e261e8055ea254bda53aa9.1697117993.git.michal.simek@amd.com
2023-11-07arm64: zynqmp: Disable the lock option for mini qspiVenkatesh Yadav Abbarapu
As mini configs are required only for flashing the images, so disabling the lock config which will save nearly 6KB of memory. Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Signed-off-by: Michal Simek <[email protected]> Link: https://lore.kernel.org/r/374d6b3a46d19b7ee171dfe8071676098db93e25.1697117869.git.michal.simek@amd.com
2023-11-07arm64: versal_net: Disable the lock option for mini ospi and qspiVenkatesh Yadav Abbarapu
As mini configs are required only for flashing the images, so disabling the lock config which will save nearly 6KB of memory. Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]>
2023-11-07arm64: versal: Disable the lock option for mini ospi and qspiVenkatesh Yadav Abbarapu
As mini configs are required only for flashing the images, so disabling the lock config which will save nearly 6KB of memory. Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]>
2023-11-07configs: Add support in Kconfig and convert for armada boardsAlgapally Santosh Sagar
Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration. Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files to allow enabling them for armada boards. Signed-off-by: Algapally Santosh Sagar <[email protected]> Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]> Reviewed-by: Simon Glass <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Michal Simek <[email protected]>
2023-11-06configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <[email protected]>
2023-11-06bmips: Add Inteno XG6846 boardLinus Walleij
This adds support for the Inteno XG6846 board based on the Broadcom MIPS 6328 SoC. The default boot will read a uImage from flash and boot it. Reviewed-by: Daniel Schwierzeck <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2023-11-03board: asus: lg: move config fragments into device boardsSvyatoslav Ryhel
Move ASUS Transformers, Grouper, P895 and P880 config fragments into their respective device directory in /board/../configs/ Signed-off-by: Svyatoslav Ryhel <[email protected]>
2023-11-03configs: grouper: drop I2C_MUXSvyatoslav Ryhel
Signed-off-by: Svyatoslav Ryhel <[email protected]>
2023-11-03configs: transformer_t30: convert bootmenu optionSvyatoslav Ryhel
Convert refresh USB to enter console. Transformers have full size USB and a dock keyboard so access to U-Boot console would be handy. Signed-off-by: Svyatoslav Ryhel <[email protected]>
2023-11-03configs: transformer_t30: support booting from USBSvyatoslav Ryhel
Change boot logic to primary try to boot from USB in dock, then from microSD and lastly from eMMC. Signed-off-by: Svyatoslav Ryhel <[email protected]>
2023-11-02configs: visionfive2: Enable JH7110 RNG driverChanho Park
Enables JH7110 RNG driver to visionfive2 board. Signed-off-by: Chanho Park <[email protected]> Reviewed-by: Heinrich Schuchardt <[email protected]>
2023-10-31corstone1000: enable PSCI resetEmekcan Aras
enable PSCI reset used for the system reset Even though Corstone-1000 does not implement the entire PSCI APIs, it relies on PSCI reset interface for the system reset. Signed-off-by: Emekcan Aras <[email protected]> Signed-off-by: Abdellatif El Khlifi <[email protected]>
2023-10-31corstone1000: add compressed kernel supportAbdellatif El Khlifi
unzip the kernel before executing it The Corstone-1000 kernel has become too large to fit in the available storage. Switching to a compressed kernel avoids the problem, but requires uncompressing it. Changes made are generated using savedefconfig. Signed-off-by: Abdellatif El Khlifi <[email protected]> Signed-off-by: Jon Mason <[email protected]> Signed-off-by: Rui Miguel Silva <[email protected]>
2023-10-31configs: nuvoton: npcm8xx: Disable CONFIG_SPI_FLASH_USE_4K_SECTORSJim Liu
disable this config to improve flash program time Signed-off-by: Jim Liu <[email protected]>
2023-10-27config: qemu: relax print and console buffer sizeHeinrich Schuchardt
QEMU print and console buffer sizes have been restricted on QEMU below their default values. One of the side effects of the print buffer size restriction is output truncation of the 'efidebug dh' command. As QEMU does not have special memory size restrictions remove the settings from the defconfig files and go with the generic defaults. Fixes: d0ee7f295d74 ("Convert CONFIG_SYS_PBSIZE to Kconfig") Fixes: d31466b382dd ("Convert CONFIG_SYS_CBSIZE to Kconfig") Signed-off-by: Heinrich Schuchardt <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2023-10-27board: toradex: verdin-imx8mp: enable usb device and fastboot supportMarcel Ziswiler
Enable USB device and fastboot support which may be used to load the Toradex Easy Installer FIT image. While at it also enable USB mass storage aka UMS support. Note that the i.MX 8M Plus recovery mode support is based on the USB boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial downloader support. Signed-off-by: Marcel Ziswiler <[email protected]> Reviewed-by: Fabio Estevam <[email protected]>
2023-10-27Merge tag 'tpm-next-27102023' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-tpm bootX measurements and measurement API moved to u-boot core: Up to now, U-Boot could perform measurements and EventLog creation as described by the TCG spec when booting via EFI. The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained both EFI specific code + the API needed to access the TPM, extend PCRs and create an EventLog. The non-EFI part proved modular enough and moving it around to the TPM subsystem was straightforward. With that in place we can have a common API for measuring binaries regardless of the boot command, EFI or boot(m|i|z), and contructing an EventLog. I've tested all of the EFI cases -- booting with an empty EventLog and booting with a previous stage loader providing one and found no regressions. Eddie tested the bootX part. Eddie also fixed the sandbox TPM which couldn't be used for the EFI code and it now supports all the required capabilities. This had a slight sideeffect in our testing since the EFI subsystem initializes the TPM early and 'tpm2 init' failed during some python tests. That code only opens the device though, so we can replace it with 'tpm2 autostart' which doesn't error out and still allows you to perfom the rest of the tests but doesn't report an error if the device is already opened. There's a few minor issues with this PR as well but since testing and verifying the changes takes a considerable amount of time, I prefer merging it now. Heinrich has already sent a PR for -master containing "efi_loader: fix EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will cause any conflicts, but in any case they should be trivial to resolve. Both the EFI and non-EFI code have a Kconfig for measuring the loaded Device Tree. The reason this is optional is that we can't reason when/if devices add random info like kaslr-seed, mac addresses etc in the DT. In that case measurements are random, board specific and eventually useless. The reason it was difficult to fix it prior to this patchset is because the EFI subsystem and thus measurements was brought up late and DT fixups might have already been applied. With this patchset we can measure the DT really early in the future. Heinrich also pointed out that the two Kconfigs for the DTB measurements can be squashed in a single one and that the documentation only explains the non-EFI case. I agree on both but as I said this is a sane working version, so let's pull this first it's aleady big enough and painful to test.
2023-10-27Merge tag 'u-boot-amlogic-20231027' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-amlogic - Fix environment saving for new Android boot features on vim3*_android - Add SPIFC support for Amlogic A1 - Add DFU RAM boot step when booting over USB
2023-10-27ARM: amlogic: ad401: enable SPIFCIgor Prusov
Enable Amlogic A1 SPI FLash Controller support. Signed-off-by: Igor Prusov <[email protected]> Reviewed-by: Neil Armstrong <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Neil Armstrong <[email protected]>
2023-10-27test: Add sandbox TPM boot measurementEddie James
Use the sandbox TPM driver to measure some boot images in a unit test case. Signed-off-by: Eddie James <[email protected]> Reviewed-by: Simon Glass <[email protected]> Acked-by: Ilias Apalodimas <[email protected]> Signed-off-by: Ilias Apalodimas <[email protected]>
2023-10-26ARM: meson: enable USB DFU + RAM on Amlogic boards with USB GadgetNeil Armstrong
Enable DFU as an alternate USB boot method when script wasn't uploaded, this fixes USB full boot on G12/SM1 boards. Link: https://lore.kernel.org/r/[email protected] [narmstrong: remove dfu from ad401] Signed-off-by: Neil Armstrong <[email protected]>
2023-10-26ARM: meson: enable FIT with LEGACY_IMAGE_FORMAT on all configsNeil Armstrong
Allow all boards to boot with a fitImage, but keep support for Legacy image format for now. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Neil Armstrong <[email protected]>
2023-10-26configs: khadas-vim3*_android: fix environment savingMattijs Korpershoek
The environment is used to configure some additional boot features such as: * extra boot arguments * enable AVB (Android Verified Boot) verification Right now, we cannot store it in eMMC: Loading Environment from nowhere... OK Fix it by enabling the appropriate options in the defconfig Fixes: b749d5ecdc06 ("configs: meson64_android: define raw parts for bootloader") Signed-off-by: Mattijs Korpershoek <[email protected]> Reviewed-by: Neil Armstrong <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Neil Armstrong <[email protected]>
2023-10-26arm: kirkwood: Enable bootstd for Zyxel NSA310S boardTony Dinh
Enable bootstd for Zyxel NSA310S board, and remove distroboot. Signed-off-by: Tony Dinh <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2023-10-26arm: kirkwood: Enable bootstd for Pogo V4 boardTony Dinh
Enable bootstd for Pogo V4 board, and remove distroboot. Signed-off-by: Tony Dinh <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2023-10-26arm: mvebu: turris_mox: Extend to support RIPE Atlas ProbeMarek Behún
Extend Turris Mox board code to support CZ.NIC's RIPE Atlas Probe. Signed-off-by: Marek Behún <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2023-10-24sandbox: add SCMI power domain protocol support for testingAKASHI Takahiro
SCMI power domain management protocol is supported on sandbox for test purpose. Add fake agent interfaces and associated power domain devices. Signed-off-by: AKASHI Takahiro <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2023-10-24cmd: mbr: Allow 4 MBR partitions without need for extendedAlexander Gendin
Current code allows up to 3 MBR partitions without extended one. If more than 3 partitions are required, then extended partition(s) must be used. This commit allows up to 4 primary MBR partitions without the need for extended partition. Add mbr test unit. In order to run the test manually, mmc6.img file of size 12 MiB or greater is required in the same directory as u-boot. Test also runs automatically via ./test/py/test.py tool. Running mbr test is only supported in sandbox mode. Signed-off-by: Alex Gendin <[email protected]> [ And due to some further changes for testing ] Signed-off-by: Simon Glass <[email protected]>
2023-10-24Merge tag 'u-boot-rockchip-20231024' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-rockchip - Add Board: rk3588 NanoPC-T6, Orange Pi 5, Orange Pi 5 Plus; - clk driver fix for rk3568 and rk3588; - rkmtd cmd support for rockchip nand device; - dts update and sync from linux;
2023-10-24Merge tag 'u-boot-imx-20231024' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20231024 ------------------- CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/18211 - Fixes for MC2432 Eeprom - i.MX93 ADC - Secondary boot mode on i.MX8M
2023-10-24rockchip: configs: sandbox: enable rkmtd commandJohan Jonker
Enable rkmtd command for testing with sandbox_defconfig and sandbox64_defconfig. Signed-off-by: Johan Jonker <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2023-10-24board: rockchip: Add Xunlong Orange Pi 5 PlusJonas Karlman
Xunlong Orange Pi 5 Plus is a single-board computer based on the Rockchip RK3588 SoC. The board provides abundant interfaces, including two HDMI output ports, one HDMI input port, two 2.5G Ethernet ports, M.2 M-Key slot, M.2 E-Key slot, two USB 3.0, two USB 2.0, and two Type-C. Features tested on a Orange Pi 5 Plus 4GB v1.2: - SD-card boot - eMMC boot - SPI Flash boot - PCIe/NVMe - USB 2.0 host - Ethernet Device tree is imported from linux v6.7-rockchip-dts64-1 tag. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-24board: rockchip: Add Xunlong Orange Pi 5Jonas Karlman
Xunlong Orange Pi 5 is a single-board computer based on the Rockchip RK3588S SoC. The board provides abundant interfaces, HDMI output, GPIO interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0, etc. Features tested on a Orange Pi 5 4GB v1.2: - SD-card boot - SPI Flash boot - PCIe/NVMe - USB 2.0 host - Ethernet Device tree is imported from linux v6.7-rockchip-dts64-1 tag. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-24rockchip: rk3588-rock-5b: Sync USB3 nodes from mainline linux patchesJonas Karlman
The device tree for rk3588 and rock-5b contain usb3 nodes that have deviated too much from current state of submitted mainline linux usb3 patches, see [1]. Sync usb3 related nodes from latest patches and collaboras rk3588 tree so that dwc3-generic driver can be updated to include support for the rockchip,rk3588-dwc3 compatible in the future, use rockchip,rk3568-dwc3 compatible until final node is merged in linux maintainer tree. [1] https://lore.kernel.org/lkml/[email protected]/ Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-24rockchip: rk3588-rock-5b: Enable support for PCIe SATA cardsJonas Karlman
Enable support for PCIe SATA cards and the on-board SATA controller. This also revert use of CONFIG_PCI_INIT_R in order to speed up boot from eMMC or SD-cards. Standard boot will initialize pci after faster boot media have been enumerated. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Christopher Obbard <[email protected]> Tested-by: Christopher Obbard <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-24rockchip: rk3588-rock-5a: Enable support for USB 2.0 portsJonas Karlman
Enable Kconfig options for the two USB 2.0 ports and bottom USB 3.0 port on ROCK 5 Model A. Signed-off-by: Jonas Karlman <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2023-10-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <[email protected]>
2023-10-23Merge tag 'u-boot-at91-2024.01-b' of ↵Tom Rini
https://source.denx.de/u-boot/custodians/u-boot-at91 Second set of u-boot-at91 features for the 2024.01 cycle This feature set a new board named Conclusive KSTR sama5d27 with some small prerequisites patches.
2023-10-23board: Add support for Conclusive KSTR-SAMA5D27Artur Rojek
Introduce support for Conclusive KSTR-SAMA5D27 Single Board Computer. Co-developed-by: Jakub Klama <[email protected]> Signed-off-by: Jakub Klama <[email protected]> Co-developed-by: Marcin Jabrzyk <[email protected]> Signed-off-by: Marcin Jabrzyk <[email protected]> Signed-off-by: Artur Rojek <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-08-11 12:00:58 +0000