summaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)Author
2017-12-07sandbox: Adjust pre-console address to avoid conflictSimon Glass
We cannot use sandbox memory at 0 since other things use memory at that address. Move it up out of the way. Note that the pre-console buffer is currently disabled with sandbox, but this change will avoid confusion if it is manually enabled. Signed-off-by: Simon Glass <[email protected]>
2017-12-04omap3: evm: Explicitly use DISTRO_DEFAULTS features at startupDerald D. Woods
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot [fallback 1] Check MMC 0:1 zImage and run mmcbootz [fallback 2] Check MMC 0:1 uImage and run mmcboot [fallback 3] Check NAND partitions and run nandboot If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is followed. Signed-off-by: Derald D. Woods <[email protected]>
2017-12-04ARM: arch-meson: build memory banks using reported memory from registersNeil Armstrong
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware and a secondary BL32 firmware. Since mid-2017, the reserved memory address of the BL31 firmware was moved and grown for security reasons. But mainline U-Boot and Linux has the old address and size fixed. These SoCs have a register interface to get the two firmware reserved memory start and sizes. This patch adds a dynamic reservation of the memory zones in the device tree bootmem reserved memory zone used by the kernel in early boot. To be complete, the memory zones are also added to the EFI reserved zones. Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2]. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html Changes since v1: - switched the #if to if(IS_ENABLED()) to compile all code paths - renamed function to meson_board_add_reserved_memory() - added a mem.h header with comment - updated all boards ft_board_setup() Changes since RFC v2: - reduced preprocessor load - kept Odroid-C2 static memory mapping as exception Changes since RFC v1: - switch to fdt rsv mem table and efi reserve memory - replaced in_le32 by readl() Reviewed-by: Simon Glass <[email protected]> Signed-off-by: Neil Armstrong <[email protected]> [trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <[email protected]>
2017-12-04arm: Add Khadas VIM support based on Meson GXL familyNeil Armstrong
This adds platform code for the Khadas VIM board based on a Meson GXL (S905X) SoC with the Meson GXL configuration. This initial submission supports UART, MMC/SDCard and Ethernet with the Internal RMII PHY. The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13 stable tree as of 4.13.8. Reviewed-by: Simon Glass <[email protected]> Signed-off-by: Neil Armstrong <[email protected]>
2017-12-04arm: Add LibreTech CC support based on Meson GXL familyNeil Armstrong
This adds platform code for the Libre Computer CC "Le Potato" board based on a Meson GXL (S905X) SoC with the Meson GXL configuration. This initial submission supports UART, MMC/SDCard and Ethernet with the Internal RMII PHY. The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13 stable tree as of 4.13.8. Reviewed-by: Simon Glass <[email protected]> Signed-off-by: Neil Armstrong <[email protected]>
2017-12-04add support for Raspberry Pi Zero WDmitry Korunov
Signed-off-by: Dmitry Korunov <[email protected]>
2017-11-30rockchip: rk3128: add defconfig for evb-rk3128Kever Yang
Enable board config for evb-rk3128. Serial output and eMMC works in this version. Signed-off-by: Kever Yang <[email protected]> Acked-by: Philipp Tomsich <[email protected]> Reviewed-by: Philipp Tomsich <[email protected]>
2017-11-30Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-shTom Rini
2017-11-30Merge git://git.denx.de/u-boot-x86Tom Rini
2017-11-30ARM: rmobile: Rework the ULCB CPLD driverMarek Vasut
Rework the ULCB CPLD driver and make it into a sysreset driver, since that is what the ULCB CPLD driver is mostly for. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2017-11-30x86: conga-qeval20-qa3-e3845: Adjust VGA rom addressAnatolij Gustschin
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image can be built again. Signed-off-by: Anatolij Gustschin <[email protected]> Reviewed-by: Stefan Roese <[email protected]> Acked-by: Bin Meng <[email protected]>
2017-11-29board: laird: add WB50N CPU moduleBen Whitten
This board is based on the Atmel sama5d3 eval boards. Supporting the following features: - Boot from NAND Flash - Ethernet - FIT - SPL Signed-off-by: Ben Whitten <[email protected]> Signed-off-by: Dan Kephart <[email protected]>
2017-11-29board: laird: add WB45N CPU moduleBen Whitten
This board is based on the Atmel 9x5 eval board. Supporting the following features: - Boot from NAND Flash - Ethernet - FIT - SPL Signed-off-by: Ben Whitten <[email protected]> Signed-off-by: Dan Kephart <[email protected]>
2017-11-29board: atmel: add sama5d2_ptc_ek boardLudovic Desroches
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board which was a prototype. Signed-off-by: Ludovic Desroches <[email protected]> Signed-off-by: Wenyou Yang <[email protected]>
2017-11-29configs: stm32f746-disco: enable MISC/DM_RESET/STM32_RESET and STM32_RCCPatrice Chotard
This allows to add rcc MFD support to stm32f746-disco board This rcc MFD driver manages clock and reset for STM32 SoCs family Signed-off-by: Patrice Chotard <[email protected]> Reviewed-by: Vikas Manocha <[email protected]>
2017-11-30nds32: board: Support ftsdc010 DM.Rick Chen
AG101P/AE3XX enable ftsdc010 dm flow. Signed-off-by: Rick Chen <[email protected]>
2017-11-30spi: nds_ae3xx: Rename nds_ae3xx_spi as atcspi200_spiRick Chen
atcspi200 is Andestech spi ip which is embedded in AE3XX and AE250 platforms. So rename as atcspi200 will be more reasonable to be used in different platforms. Signed-off-by: Rick Chen <[email protected]>
2017-11-30ae3xx: timer: Rename AE3XX to ATCPIT100Rick Chen
ATCPIT100 is Andestech timer IP which is embeded in AE3XX and AE250 boards. So rename AE3XX to ATCPIT100 will be more make sence. Signed-off-by: rick <[email protected]> Signed-off-by: Rick Chen <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-11-30ARM: rmobile: Migrate boards to RCar IIC driversMarek Vasut
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC driver instead. The SH I2C driver should be deprecated and removed eventually. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2017-11-30ARM: rmobile: Use PRR driver on all Gen3 boardsMarek Vasut
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is needed very early and turn on the CONFIG_SYSCON to allow the PRR driver to bind as a syscon uclass. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2017-11-30ARM: rmobile: Enable xHCI on RCar Gen3 boardsMarek Vasut
Enable the XHCI support on all boards. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2017-11-30ARM: rmobile: Remove CONFIG_CMD_SDRAM from Salvator-XMarek Vasut
This command is useless on Salvator-X as it is reading DRAM info from SPD. We have no SPD on Salvator-X. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2017-11-30ARM: rmobile: Enable Micrel KSZ90x1 PHY driver on ULCBMarek Vasut
Enable the Micrel KSZ90x1 driver on ULCB, since the board is populated with KSZ9031 and without this driver, the PHY cannot be operated. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2017-11-29Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2018.1 Zynq: - Add support for Syzygy and cc108 boards - Add support for mini u-boot configurations (cse) - dts updates - config/defconfig updates in connection to Kconfig changes - Fix psu_init handling ZynqMP: - SPL fixes - Remove slcr.c - Fixing r5 startup sequence - Add support for external pmufw - Add support for new ZynqMP chips - dts updates - Add support for zcu102 rev1.0 board Drivers: - nand: Support external timing setting and board init - ahci: Fix wording - axi_emac: Wait for bit, non processor mode, readl/write conversion - zynq_gem: Fix SGMII/PCS support
2017-11-29arm: zynq: Enable debug uart on zc706Michal Simek
Enable debug uart by default. Signed-off-by: Michal Simek <[email protected]>
2017-11-29ARM: uniphier: set CONFIG_LOGLEVEL to 6Masahiro Yamada
Print out KERN_NOTICE or higher level log messages. Signed-off-by: Masahiro Yamada <[email protected]>
2017-11-29ARM: openrd: set CONFIG_LOGLEVEL to 2Masahiro Yamada
These boards are on the boundary of "u-boot-nodtb.bin exceeds file size limit" error. Reduce the log-level to save memory footprint. Signed-off-by: Masahiro Yamada <[email protected]>
2017-11-28arm64: zynqmp: Add revision to identification stringMichal Simek
It is good to see revision in boot log. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm64: zynqmp: Add support for zcu102 1.0 revMichal Simek
1.0 rev is the latest rev. Describe information in eeprom. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm64: zynqmp: Enable debug uart for zc1751 dc5Michal Simek
Showing uart earlier. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm: zynq: Add mini u-boot configuration for zynqMichal Simek
Add configuration files/dtses for mini u-boot configurations which runs out of OCM. ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE 0xfffc0000 +#define CONFIG_SYS_SDRAM_SIZE 0x40000 was hardcoded. Signed-off-by: Michal Simek <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-11-28arm: zynq: Move ZYNQ_SERIAL to KconfigMichal Simek
Move cadence/zynq serial driver via Kconfig Signed-off-by: Michal Simek <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-11-28arm: zynq: Enable FPGA/FPGA_XILINX via KconfigMichal Simek
Enabling fpga via Kconfig. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm: zynq: Add board support for cc108Michal Simek
cc108 board is wiring uart via PL which is good platform for SPL fpga support. Signed-off-by: Michal Simek <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-11-28arm: zynq: Enable qspi for zc770_xm013Michal Simek
Enable qspi driver and flashes for this board. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm: zynq: Enable MACRONIX flash for zc702/zc706/zc770 xm010Michal Simek
Enable MACRONIX flash for boards with QSPI enabled. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm: zynq: Enable debug console on zc770 xm010 by defaultMichal Simek
Enable debug console. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm: zynq: Enable bootz command for Xilinx platformsMichal Simek
bootz command is valid way how to boot Linux kernel. Enable it by default. Signed-off-by: Michal Simek <[email protected]>
2017-11-28arm: zynq: Add support for SYZYGY Hub boardTom McLeod
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <[email protected]> Cc: Michal Simek <[email protected]> CC: Albert Aribaud <[email protected]> Signed-off-by: Michal Simek <[email protected]>
2017-11-27spl: TI: Do not default to SPL_FIT_IMAGE_TINY being enabledTom Rini
This option prevents booting on am335x_evm at least along with most likely other platforms. Fixes: 337bbb629777 ("spl: fit: add SPL_FIT_IMAGE_TINY config to reduce code-size") Signed-off-by: Tom Rini <[email protected]>
2017-11-27Merge git://www.denx.de/git/u-boot-imxTom Rini
Signed-off-by: Tom Rini <[email protected]>
2017-11-27configs: icore-rqs: Enable falcon modeJagan Teki
Signed-off-by: Jagan Teki <[email protected]>
2017-11-27i.MX6: engicam: Add imx6q/imx6ul boards for existing boardsJagan Teki
Add new board names for existing board support imx6q - icore and icore_rqs boards imx6ul - geam6ul and isiot boards Signed-off-by: Jagan Teki <[email protected]>
2017-11-27i.MX6UL: icore: Add SPL_OF_CONTROL supportJagan Teki
Add OF_CONTROL support for SPL code. Signed-off-by: Jagan Teki <[email protected]>
2017-11-27i.MX6Q: icore: Add SPL_OF_CONTROL supportJagan Teki
Add OF_CONTROL support for SPL code. Signed-off-by: Jagan Teki <[email protected]>
2017-11-27mx6sxsabresd: Use PARTUUID to specify the rootfs locationFabio Estevam
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline. Currently the rootfs location is passed via mmcblk number and the problem with this approach is that the mmcblk number for the SD card changes depending on the kernel version. In order to avoid such issue, use the UUID method to specify the rootfs location. Signed-off-by: Fabio Estevam <[email protected]> Reviewed-by: Stefano Babic <[email protected]> Reviewed-by: Lukasz Majewski <[email protected]>
2017-11-26rockchip: defconfig: puma-rk3399: bypass ADC-based boot_mode checkPhilipp Tomsich
The boot (and fallback/emergency boot) concept for the RK3399-Q7 differs from Rockchip's reference platforms. On the RK3399-Q7, some of this functionality is present in the bootloader itself (and configurable); some is backed in hardware by the Qseven BIOS_DISABLE signal to invoke the final stages of fallbacks (i.e. either an external boot bypassing on-module memories or falling back to the BROM for USB recovery). In summary: the ADC-based boot_mode check does not apply for the RK3399-Q7 and we therefore disable it (in this commit) by setting CONFIG_BOOT_MODE_REG to 0. Signed-off-by: Philipp Tomsich <[email protected]>
2017-11-26rockchip: defconfig: lion-rk3368: sync up with SPL changes for ATFPhilipp Tomsich
This tracks the SPL changes for ATF for the RK3368-uQ7: * renames ATF_SUPPORT to ATF * drops CONFIG_SPL_ATF_TEXT_BASE (now dynamically retrieved from the .itb file) Signed-off-by: Philipp Tomsich <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-11-26rockchip: defconfig: puma-rk3399: sync up with SPL changes for ATFPhilipp Tomsich
This defconfig update makes use of the new features: * CONFIG_ROCKCHIP_SPL_RESERVE_IRAM is now set to 0, as there is no overlap between the M0 firmware and the ATF (we load this to DRAM and relocate it to its final location within the ATF) * tracks the ATF_SUPPORT -> ATF renaming Signed-off-by: Philipp Tomsich <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2017-11-26rockchip: defconfig: firefly-rk3399: sync up with SPL changes for ATFPhilipp Tomsich
This tracks the SPL changes for ATF for the Firefly: * renames ATF_SUPPORT to ATF * drops CONFIG_SPL_ATF_TEXT_BASE Signed-off-by: Philipp Tomsich <[email protected]> Reviewed-by: Simon Glass <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-06-01 13:58:29 +0000