| Age | Commit message (Collapse) | Author |
|---|
|
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py and update
scripts/pylint.base
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Move the SATA options inside an 'if SATA' part, so they are grouped.
Fix the 'Complient' typo while we are here.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_REMAKE_ELF
Signed-off-by: Alper Nebi Yasak <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Pali Rohár <[email protected]>
|
|
Add configs to enable booting ethfw core in j721e
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
Enable fs_loader compilation at SPL Level.
Signed-off-by: Keerthy <[email protected]>
[Amjad: fix compilation failures for J721e platform]
Signed-off-by: Amjad Ouled-Ameur <[email protected]>
|
|
Expand SPL_MULTI_DTB_FIT to accommodate new SPL IPU nodes.
Signed-off-by: Amjad Ouled-Ameur <[email protected]>
|
|
Enable A72 specific configs for J721S2
Signed-off-by: David Huang <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Signed-off-by: Hari Nagalla <[email protected]>
|
|
Enable R5 SPL specific configs for J721S2.
Signed-off-by: David Huang <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Vignesh Raghavendra <[email protected]>
Signed-off-by: Hari Nagalla <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20211022
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/10887
- imx8 : Toradex Verdin MX8M Plus
Kontron pitx-imx8m
- imx8ulp: several fixes and improvements
- imx6ull fixes
- switching to binman
|
|
Move setting the default boot command to the
apalis/colibri_imx6_defconfig. It allows replacing the command
without code modification.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The size of the board file is limited to 520192 bytes. This conflicts with
the size requirement for the UEFI code.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
Signed-off-by: Heiko Thiery <[email protected]>
|
|
This option is selected implicitly when [SPL_]CLK_IMXRT10{20|50} is selected.
Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-by: Giulio Benetti <[email protected]>
|
|
The i.MX8M Nano can boot over USB using the boot ROM instead of
adding extra code to SPL to support USB drivers, etc. However,
when booting from USB, the environment doesnt' know where to load
and causes a hang. Fix this hang by supporting CONFIG_ENV_IS_NOWHERE=y.
It only falls back to this condition when booting from USB, so it
does not impact MMC booting.
Suggested-by: Michael Nazzareno Trimarchi <[email protected]>
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
With the updated device tree's having USB support, enable in
U-Boot. This also requires the addition of the imx8m power
domain, since the USB is gated by the power domain controller.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
CONFIG_SPL_MMC and CONFIG_SPL_SERIAL
Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
|
|
The new configs/imx28_xea_sb_defconfig is introduced to facilitate
building the single binary u-boot.sb fox XEA board.
The biggest distinction from "normal" XEA imx28_xea_sb_defconfig is
support for USB mass storage devices (pen drives).
To achieve that, the CONFIG_DM_USB is enabled and supported.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Add support for iMX8MN VAR-SOM-MX8M-NANO board. Enables support for:
- 1GiB DDR4 RAM
- 16 GiB eMMC
- SD card
- Gigabit ethernet
- USBOTG1 peripheral - fastboot
Signed-off-by: Ariel D'Alessandro <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The FXL6408 GPIO expander manages critical devices,
including on-module USB hub. Configure the expander to
switch the USB hub into bypass mode, allowing to use
on-carrier-board USB hub.
Signed-off-by: Oleksandr Suvorov <[email protected]>
Signed-off-by: Oleksandr Suvorov <[email protected]>
|
|
Previously these two options are called CONFIG_SPL_MMC_SUPPORT
and CONFIG_SPL_SERIAL_SUPPORT. During the transition they are
removed by accident. Thus adding them back.
Signed-off-by: Ying-Chun Liu (PaulLiu) <[email protected]>
Cc: uboot-imx <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The Lichee Pi Nano is a board based on the F1C100s.
Add defconfigs for it.
Signed-off-by: Icenowy Zheng <[email protected]>
Signed-off-by: Jesse Taube <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
The initial patch had typos that caused four defconfigs to miss the
symbol transition to Kconfig. CONFIG_SYS_QE_FW_ADDR and
CONFIG_SYS_FMAN_FW_ADDR are currently initialized to 0 by default
on these builds, which prevents the firmware from loading.
Add the correct symbols to these defconfigs.
Fixes: a97a071d10d2b ("configs: fsl: migrate FMAN/QE specific defines to Kconfig")
Signed-off-by: Camelia Groza <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Make it in a same way as on the other FOXMC products, this also helps to
avoid unwanted stop caused by some terminal servers that are sending junk
on the serial line.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch: 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the EXPU1 NOR layout.
- Extending mtd partitions according defined EXPU1 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This is used by out ESW for reading u-boot build version.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This is used by out ESW for reading u-boot build version.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the SELI8 NOR layout.
- Extending mtd partitions according defined SELI8 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Ethernet
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The Pogoplug V4 board has the network chip Marvell 88E1116R. So to
properly configure the network, enable CONFIG_PHY_MARVELL to activate
the compatible driver M88E1118R.
- This patch depends on the series:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
Signed-off-by: Tony Dinh <[email protected]>
|
|
Add board header, defconfig, and implementation files for Pogoplug V4.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
|
|
Enable config options needed to support Ethernet boot on AM64x SK.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Add to support rsa 3072 bits algorithm in tools
for image sign at host side and adds rsa 3072 bits
verification in the image binary.
Add test case in vboot for sha384 with rsa3072 algorithm testing.
Signed-off-by: Jamin Lin <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This is enabled for quite a few boards which don't create ACPI tables.
Tidy this up by dropping the option for some boards.
Signed-off-by: Simon Glass <[email protected]>
|
|
These have sadly found their way to ARM now. Allow any arch to support
generating ACPI tables.
Disable this for the tools build.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Commit 270f8710f92f ("crc32: Add crc32 implementation using
__builtin_aarch64_crc32b") enabled the usage of ARMv8 CRC instructions
by default, for all arm64 builds. And indeed all Arm Ltd. v8 Cortex-A
cores support the instructions, and they are mandatory starting with
architecture revision v8.1, so realistically every known hardware
implementation should support them.
The Arm Fastmodel however defaults to the bare minimum ARMv8 feature set
by default, which means v8.0 without the CRC instructions, so U-Boot
hangs very early at the moment, without any output (the boot-wrapper or
TF-A printing the last visible lines).
Support for those instructions can be enabled on the model command line
by either:
-C cluster0.cpu0.enable_crc32=1 (for each core)
or by using a higher architecture revision by default:
-C cluster0.has_arm_v8-1=1 (for each cluster)
Of course any arch revision higher than v8.1 would work as well.
But for the sake of a smooth out-of-the-box experience, let's just
disable the usage of those instructions in the defconfig, to avoid
random hangs without any clues.
Reported-by: Ross Burton <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Instead of a custom cpu_reset function, use the sysreset_psci
instead to reduce redundant code clutter.
Signed-off-by: Adam Ford <[email protected]>
|
