| Age | Commit message (Collapse) | Author |
|---|
|
This patch implements the is_pci_host() function in a similiar way
as it is used on 440 targets.
The former path with CONFIG_PCI_HOST == PCI_HOST_AUTO does not
build on 405EP targets because checking the PCI arbiter is different.
So putting the fixed code into a separate function makes the code
more readable.
Also using is_pci_host() on 405 brings 405 and 440 PCI code
a little bit closer.
In preparation for an upcoming 405EP based PMC module I made this
function weak so that it can be overwritten from board specific code.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch fixes a debug compilation error for PPC4xx platforms, all
other architectures are not affected by this change. The 'handler'
pointer was undefined. The fix is exercised and has effect only if
DEBUG is defined.
Signed-off-by: Alessio Centazzo [email protected]
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch fixes printf format string compilation warnings in several
debug statements. It also fixes the dump of DDR controller MQ registers
found on some 44x and 46x platforms. The current register dump code
uses incorrect DCRs to access these registers.
Signed-off-by: Felix Radensky <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
all sh boards use the same cpu linker script so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver
Signed-off-by: Prafulla Wadaskar <[email protected]>
|
|
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <[email protected]>
Acked-by: Andrea Gallo <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <[email protected]>
Acked-by: Andrea Gallo <[email protected]>
|
|
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: HeungJun, Kim <[email protected]>
CC: Dirk Behme <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Kirkwood family controllers are highly integrated SOCs
based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.
SOC versions supported:-
1) 88F6281-A0 define CONFIG_KW88F6281_A0
2) 88F6192-A0 define CONFIG_KW88F6192_A0
Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support
Contributors:
Yotam Admon <[email protected]>
Michael Blostein <[email protected]
Reviewed-by: Ronen Shitrit <[email protected]>
Acked-by: Stefan Rose <[email protected]>
Signed-off-by: Prafulla Wadaskar <[email protected]>
|
|
Signed-off-by: Peter Tyser <[email protected]>
Reviewed-by: Ira W. Snyder <[email protected]>
Tested-by: Ira W. Snyder <[email protected]>
Acked-by: Kim Phillips <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <[email protected]>
Acked-by: Kim Phillips <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
The calculate for rank density in compute_ranksize() for DDR3 used all
integers for the expression, so the result was also a 32-bit integer, even
though the 'bsize' variable is a u64. Fix the expression to calculate a
true 64-bit value.
Signed-off-by: Timur Tabi <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Also update dmacpy()'s argument order to match memcpy's and use
phys_addr_t/phy_size_t for address/size arguments
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Unify with 83xx and 85xx and use CPU_TYPE_ENTRY. We are going to use
this to convey the # of cores and DDR width in the near future so its
good to keep in sync.
Signed-off-by: Kumar Gala <[email protected]>
|
|
Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch adds generic code to support Freescale's i.MX27 SoCs.
Signed-off-by: Ilya Yanok <[email protected]>
|
|
Signed-off-by: Magnus Lilja <[email protected]>
|
|
This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.
It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.
Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).
The patch is based on the work by Maxim Artamonov.
Signed-off-by: Maxim Artamonov <[email protected]>
Signed-off-by: Magnus Lilja <[email protected]>
|
|
Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.
Signed-off-by: Magnus Lilja <[email protected]>
|
|
the lowlevel init sequence is the same so unify it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
The debug tools that interface with the other side of the JTAG console
got much slower when generalizing things, so bump up the default timeout
value on the U-Boot side to cope. Hopefully at some point we can improve
the debug tools to speed things back up.
Signed-off-by: Vivi Li <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c
Signed-off-by: Ben Warren <[email protected]>
|
|
This driver has been renamed davinci_emac.c
Signed-off-by: Ben Warren <[email protected]>
|
|
The following changes were made to sync up the DMA code between the 85xx
and 86xx architectures which will make it easier to break out common
8xxx DMA code:
85xx:
- Don't set STRANSINT and SPCIORDER fields in SATR register. These bits
only have an affect when the SBPATMU bit is set.
- Write 0xffffffff instead of 0xfffffff to clear errors in the DMA
status register. We may as well clear all 32 bits of the register...
86xx:
- Add CONFIG_SYS_MPC86xx_DMA_ADDR define to address DMA registers
- Add clearing of errors in the DMA status register when initializing
the controller
- Clear the channel start bit in the DMA mode register after a transfer
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Break out DMA structures for the Freescale MPC85xx and MPC86xx cpus to
reduce a large amount of code duplication
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
The uec driver contains code to hard code configuration information for the uec
ethernet controllers. This patch creates an array of uec_info structures, which
are then parsed by the corresponding driver instance to determine configuration.
It also creates function uec_standard_init() to initialize all UEC interfaces
for 83xx and 85xx.
Signed-off-by: Haiying Wang <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Signed-off-by: Haiying Wang <[email protected]>
Acked-by: Timur Tabi <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Signed-off-by: Kumar Gala <[email protected]>
|
|
Its reasonable that we may have ethernet devices but dont have drivers
or support enabled for them in u-boot and want the device tree fixed up.
Unconditionally calling the ethernet fixup is fine since if we dont have
ethernet nodes that match (or aliases) we will not attempt to do
anything.
Signed-off-by: Kumar Gala <[email protected]>
Acked-by: Timur Tabi <[email protected]>
|
|
This is needed for the upcoming esd MECP5123 board port which uses
I2C EEPROM for environment storage.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
Acked-by: Heiko Schocher<[email protected]>
|
|
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-
* Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
cpu/mpx83xx/cpu_init.c
* Board specific usb_phy_type is read from the environment
* Adds USB EHCI specific structure in include/usb/ehci-fsl.h
* Copyrights revamped in most of the following files
Signed-off-by: Vivek Mahajan <[email protected]>
Signed-off-by: Remy Bohmer <[email protected]>
|
|
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
|
|
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
|
|
This patch removes the duplicated code for baudrate generator configuration
in the PSC serial_init() implementation by calling serial_setbrg() instead
of duplicating the code.
Signed-off-by: Stefan Roese <[email protected]>
|
|
The wrong input frequency was used in serial_setbrg(). This patch fixes
this by using ips_clk as input frequency for the PSC baudrate generator.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: John Rigby <[email protected]>
|
|
This commit changes the MPC512x code to use I/O accessor calls (i.e.
out_*() and in_*()) instead of using deprecated pointer accesses.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: John Rigby <[email protected]>
|
|
- add GPIO module description
- add Address Latch Timing Register description
- add IO Control Memory Map
- add FEC Memory Map
Also change board/freescale/mpc5121ads/mpc5121ads.c and
cpu/mpc512x/iopin.c as needed.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: John Rigby <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: John Rigby <[email protected]>
|
|
Get rid of variable declaration in the middle of the code.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: John Rigby <[email protected]>
|
|
We will soon see several new MPC521x based boards added. This patch
moves files that are not board specific to a common directory so they
can be shared by all such ports. It also splits off common IDE code
into a new file, cpu/mpc512x/ide.c .
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: John Rigby <[email protected]>
|
