| Age | Commit message (Collapse) | Author |
|---|
|
Add dt-binding for MediaTek xHCI host controller
Signed-off-by: Chunfeng Yun <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: Weijie Gao <[email protected]>
|
|
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
Add compatible "st,stm32mp1-hsotg" and associated driver data to manage
the usb33d-supply and the ST specific register for VBus sensing.
Signed-off-by: Patrick Delaunay <[email protected]>
# Conflicts:
# drivers/usb/gadget/dwc2_udc_otg.c
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
Minimal conversion to driver model by using the uclass
UCLASS_USB_GADGET_GENERIC based on:
- reset uclass
- clock uclass
- generic uclass.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Nadav Haklai <[email protected]>
Cc: Neta Zur Hershkovits <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Haim Boot <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
|
This adds a property to indicate a port which can switch between host and device
mode.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This file is taken from the Linux mailing list.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
