| Age | Commit message (Collapse) | Author |
|---|
|
Grame is still listed since he has agreed to continue with some review.
Also add an alias to shorten things.
Signed-off-by: Simon Glass <[email protected]>
|
|
This makes the FAT and ext4 filesystem implementations build if
CONFIG_FS_{FAT,EXT4} are defined, rather than basing the build on
whether CONFIG_CMD_{FAT,EXT*} are defined. This will allow the
filesystems to be built separately from the filesystem-specific commands
that use them. This paves the way for the creation of filesystem-generic
commands that used the filesystems, without requiring the filesystem-
specific commands.
Minor documentation changes are made for this change.
The new config options are automatically selected by the old config
options to retain backwards-compatibility.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Benoît Thébaudeau <[email protected]>
|
|
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Wolfgang Grandegger <[email protected]>
|
|
SX1 does not build properly by itself, is not built
as part of MAKEALL arm or MAKEALL -a arm, and is only
present in Makefile, not boards.cfg. As it also has no
entry in MAINTAINERS, it is orphan and non-functional.
Remove it.
Signed-off-by: Albert ARIBAUD <[email protected]>
|
|
This stuff has been rotting in the tree for a year now. Remove it.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <[email protected]>
Signed-off-by: Jason Jin <[email protected]>
Signed-off-by: Alison Wang <[email protected]>
|
|
|
|
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Signed-off-by: Shengzhou Liu <[email protected]>
Signed-off-by: Roy Zang <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
|
|
Move spin table to cached memory to comply with ePAPR v1.1.
Load R3 with 64-bit value if CONFIG_SYS_PPC64 is defined.
'M' bit is set for DDR TLB to maintain cache coherence.
See details in doc/README.mpc85xx-spin-table.
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
|
|
Based on populated DIMMs, automatically select from cs0_cs1_cs2_cs3 or
cs0_cs1 interleaving, or non-interleaving if not available.
Fix the message of interleaving disabled if controller interleaving
is enabled but DIMMs don't support it.
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
|
|
Add code for configuring VSC3316/3308 crosspoint switches
Add README to understand the APIs
- VSC 3316/3308 is a low-power, low-cost asynchronous crosspoint switch
capable of data rates upto 11.5Gbps. VSC3316 has 16 input and 16
output ports whereas VSC3308 has 8 input and 8 output ports.
Programming of these devices are performed by two-wire or four-wire
serial interface.
Signed-off-by: Shaveta Leekha <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
|
|
Implement kerneldoc template for linker-generated arrays. This is
the first template in U-Boot that is used to generate kerneldoc
style documentation. This template is very basic.
Signed-off-by: Marek Vasut <[email protected]>
|
|
This patch converts the old method of creating a list of command
onto the new LG-arrays code. The old u_boot_cmd section is converted
to new u_boot_list_cmd subsection and LG-array macros used as needed.
Minor adjustments had to be made to the common code to work with the
LG-array macros, mostly the fixup_cmdtable() calls are now passed the
ll_entry_start and ll_entry_count instead of linker-generated symbols.
The command.c had to be adjusted as well so it would use the newly
introduced LG-array API instead of directly using linker-generated
symbols.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Mike Frysinger <[email protected]>
|
|
Conflicts:
drivers/serial/serial_lh7a40x.c
Signed-off-by: Tom Rini <[email protected]>
|
|
Add STDIO documentation template.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Tom Rini <[email protected]>
[trini: Fix DOCBOOKS line as we don't have linker_lists yet]
Signed-off-by: Tom Rini <[email protected]>
|
|
Since commit 957731ed (ARM: remove broken "lpd7a40x" boards),
lh7a40x cpu and serial driver have become unused. Remove them.
Signed-off-by: Albert ARIBAUD <[email protected]>
|
|
Add entry for kerneldoc into the git-mailrc pointing to the U-Boot ML
and myself.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Import basic CSS stylesheet for the HTML documentation. The base for
the stylesheet is taken from:
http://ds9a.nl/docbook/minimal-page.html
I customized the CSS a bit further, for example to add curvy corners
to example section and change the tint of gray. The HTML documentation
does not look that crude anymore.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Pull slightly modified version of Documentation/DocBook, the related perl
script scripts/kernel-doc and the scripts/docproc.c from Linux kernel and
implant it into U-Boot. This will allow smooth generation of kerneldoc
style documentation.
It was necessary to modify the DocBook/Makefile to work with U-Boot build
system. The changes were only minor though and involved replacing the kbuild
specific parts.
It was also necessary to replace use of variables like KERNEL_VERSION with
U_BOOT_VERSION, strings like Linux kernel with U-Boot Bootloader etc. so
the generated result actually matches.
Finally, it was necessary to adjust docproc.c, since the documentation in
U-Boot is located in doc/DocBook instead of Documentation/DocBook as is in
case of the Linux kernel.
Some parts of the DocBook Makefile are unused, but to allow easier sync with
Linux kernel, these parts are still left in. The targets enabled now are
"htmldocs" "pdfdocs" "psdocs" "xmldocs" and "cleandocs" to remove the results
of documentation build.
Linux scripts/docproc.c:
commit f0f3ca8d967462dafb815412b14ca3339b9817a6
Date: Wed Jun 15 11:53:13 2011 +0200
Linux scripts/kernel-doc:
commit 1b40c1944db445c1de1c47ffd8cd426167f488e8
Date: Sun Aug 12 10:46:15 2012 +0200
Linux Documentation/DocBook:
commit bb8187d35f820671d6dd76700d77a6b55f95e2c5
Date: Thu May 17 19:06:13 2012 -0400
Signed-off-by: Marek Vasut <[email protected]>
|
|
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.
Signed-off-by: Albert ARIBAUD <[email protected]>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <[email protected]>
|
|
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2). As these boards have long
reached EOL it seems a waste of effort trying to fix them. The vendor
has agreed to drop support for them, too. So let's get rid of them.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
cc: Kim Phillips <[email protected]>
Acked-by: Stefan Roese <[email protected]>
|
|
Support of the MINI2440 board from FriendlyARM from
an old version of u-boot :
http://repo.or.cz/r/u-boot-openmoko/mini2440.git
Currently, supporting only boot from NOR.
Signed-off-by: Gabriel Huau <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
This add README of Renesas RMOBILE.
Based doc/README.omap3.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
|
|
Signed-off-by: Pavel Machek <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Now DT support is becoming common for all new SoC's. Hence it is better
to have option for getting specific FDT from the remote server.
This patch adds support for new label i.e. 'fdt'. This will allow to
retrieve 'fdt blob' from the remote server. This patch take care for
the following scenarios.
The usage of fdt is optional.
The 'fdt blob' can be retrieved from tftp or can be available locally
or can be absent.
If 'fdt_addr_r' environment variable is set and 'fdt' label is defined
retrieve 'fdt blob' from tftp. 'fdt_addr_r' is then passed along bootm
command.
If 'fdt_addr' is set and 'fdt blob' is not retrieved from the tftp pass
'fdt_addr' to bootm command. In this case 'fdt blob' will be available
at 'fdt_addr'.
If 'fdt_addr' is not set and 'fdt blob' is not retrieve from tftp pass
NULL to boot command. In this case 'fdt blob' is not required and absent.
Signed-off-by: Chander Kashyap <[email protected]>
Acked-by: Jason Hobbs <[email protected]>
|
|
Changes in v2:
- Reword a bit more
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
Allow a board to configure a larger buffer for netconsole, but leave
the default.
Signed-off-by: Joe Hershberger <[email protected]>
Cc: Mike Frysinger <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
It is desirable to use different port numbers for sending and receiving
packets with netconsole in the case where you have more than one device
on the local subnet with netconsole enabled for broadcast. When they
use the same port for both, any output from one will look like input to
the other. This is typlically not desirable.
This patch allows the input and output ports to be specified separately
in the environment.
Signed-off-by: Joe Hershberger <[email protected]>
Cc: Mike Frysinger <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
|
|
|
|
Update Makefile change for LIBS -> LIBS-y change.
Conflicts:
Makefile
Signed-off-by: Tom Rini <[email protected]>
|
|
This board is the only board that still sticks to OneNAND IPL.
Remove this board, since we have SPL around for a while and
OneNAND is well supported in the SPL framework. The board can
be revived if necessary.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Kyungmin Park <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <[email protected]>
[[email protected]: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <[email protected]>
|
|
Add a NAND controller along with a bindings file for review.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Hi,
This adds to the documenation to explain how to use the
kwbimage.cfg file necessary to generate an image with
prefixed board setup values necessary for the kirkwood
boards.
Signed-off-by: Karl O. Pinc <[email protected]>
|
|
Signed-off-by: Karl O. Pinc <[email protected]>
|
|
The instructions are generic, so move to the generic doc.
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tomas Hlavacek<[email protected]>
|
|
Signed-off-by: Tomas Hlavacek <[email protected]>
|
|
Signed-off-by: Viktor Krivak <[email protected]>
|
|
Signed-off-by: Pavel Herrmann <[email protected]>
|
|
Signed-off-by: Tomas Hlavacek <[email protected]>
|
|
Signed-off-by: Tomas Hlavacek <[email protected]>
|
|
Signed-off-by: Viktor Krivak <[email protected]>
|
|
Signed-off-by: Pavel Herrmann <[email protected]>
|
|
Signed-off-by: Viktor Krivak <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
|
