| Age | Commit message (Collapse) | Author |
|---|
|
Fix "ram" typos for serial flash
Signed-off-by: Chance.Yang <[email protected]>
|
|
Fix up the documentation which was lost in a merge conflict in the
conversion to RST.
Fixes: 52d3df7fefe ("log: Allow LOG_DEBUG to always enable log output")
Signed-off-by: Simon Glass <[email protected]>
|
|
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <[email protected]>
Signed-off-by: Luka Kovacic <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
This adds kerneldocs for <timer.h>.
I don't know who should maintain doc/api/timer.rst, since the timer
subsystem seems to be maintained by SoC maintainers. MAINTAINERS is left
un-updated for the moment.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Update email address of Maxime Ripard in git-mailrc to match more
recently updated entry in MAINTAINERS.
commit 9bd9b2bcbee1 ("MAINTAINERS: Update my email address")
commit bf8f4c4400e3 ("MAINTAINERS: Update email address for Maxime Ripard")
Signed-off-by: Jonas Smedegaard <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Add dt-binding for MediaTek USB3 DRD Driver which it's ported
from the Linux kernel DTS binding:
Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
Commit ID:
34d0545978b6 ("dt-bindings: usb: mtu3: fix typo of DMA clock name")
Due to Dual-Role switch is not supported in Uboot, some properties
are removed or changed.
Signed-off-by: Chunfeng Yun <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add bindings for common properties, include maximum-speed,
dr_mode and phy_type
Signed-off-by: Chunfeng Yun <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
|
|
Sphinx.override_domain() is deprecated since Sphinx 1.8 and removed in
Sphinx 3.
Use Sphinx.add_domain(, override=True) instead.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Add the description of the global data pointer to the generated HTML
documentation.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
To simplify configuration and keep synchronized the PStore/Ramoops between
U-Boot and the Linux kernel, this commit dynamically adds the Ramoops
parameters defined in the U-Boot session to the Device Tree.
Signed-off-by: Frédéric Danis <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Heinrich Schuchardt <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
This patch adds a new pstore command allowing to display or save ramoops
logs (oops, panic, console, ftrace and user) generated by a previous
kernel crash.
PStore parameters can be set in U-Boot configuration file, or at run-time
using "pstore set" command. Records size should be the same as the ones
used by kernel, and should be a power of 2.
This command allows:
- to display uncompressed logs
- to save compressed or uncompressed logs, compressed logs are saved as a
compressed stream, it may need some work to be able to decompress it,
e.g. adding a fake header:
"printf "\x1f\x8b\x08\x00\x00\x00\x00\x00\x00\x00" |
cat - dmesg-ramoops-0.enc.z | gzip -dc"
- ECC part is not used to check memory corruption
- only 1st FTrace log is displayed or saved
Signed-off-by: Frédéric Danis <[email protected]>
[trini: Minor updates for current design, correct spacing in rST]
Signed-off-by: Tom Rini <[email protected]>
Cc: Heinrich Schuchardt <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
emmc, since our dtsi is still based on downstream and sdhc0 is used for
the sd card.
Signed-off-by: Andre Heider <[email protected]>
|
|
Add documentation about 'required-mode' property in /signature node
in U-Boot's control FDT.
Signed-off-by: Thirupathaiah Annapureddy <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
|
|
doc/README.log was already moved to doc/develop/logging.rst but has been
recreated by an incorrect merge.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
At present if CONFIG_LOG enabled, putting LOG_DEBUG at the top of a file
(before log.h inclusion) causes _log() to be executed for every log()
call, regardless of the build- or run-time logging level.
However there is no guarantee that the log record will actually be
displayed. If the current log level is lower than LOGL_DEBUG then it will
not be.
Add a way to signal that the log record should always be displayed and
update log_passes_filters() to handle this.
With the new behaviour, log_debug() will always log if LOG_DEBUG is
enabled.
Move log_test_syslog_nodebug() into its own file since it cannot be made
to work where it is, with LOG_DEBUG defined.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a script to process HPS handoff data and generate a header
for inclusion in u-boot specific devicetree addons. The header
should be included in the top level of u-boot.dtsi.
Signed-off-by: Dalon Westergreen <[email protected]>
Signed-off-by: Ley Foon Tan <[email protected]>
|
|
This patch adds the necessary configs and docs for FPIOA and GPIO support
on the K210.
Signed-off-by: Sean Anderson <[email protected]>
|
|
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This normalizes the documentation to conform to kernel-doc style [1]. It
also moves the documentation for pinctrl_ops inline, and adds argument and
return-value documentation. I have kept the usual function style for these
comments. I could not find any existing examples of function documentation
inside structs.
[1] https://www.kernel.org/doc/html/latest/doc-guide/kernel-doc.html
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The pinmux property allows for smaller and more compact device trees,
especially when there are many pins which need to be assigned individually.
Instead of specifying an array of strings to be parsed as pins and a
function property, the pinmux property contains an array of integers
representing pinmux groups. A pinmux group consists of the pin identifier
and mux settings represented as a single integer or an array of integers.
Each individual pin controller driver specifies the exact format of a
pinmux group. As specified in the Linux documentation, a pinmux group may
be multiple integers long. However, no existing drivers use multi-integer
pinmux groups, so I have chosen to omit this feature. This makes the
implementation easier, since there is no need to allocate a buffer to do
endian conversions.
Support for the pinmux property is done differently than in Linux. As far
as I can tell, inversion of control is used when implementing support for
the pins and groups properties to avoid allocating. This results in some
duplication of effort; every property in a config node is parsed once for
each pin in that node. This is not such an overhead with pins and groups
properties, since having multiple pins in one config node does not occur
especially often. However, the semantics of the pinmux property make such a
configuration much more appealing. A future patch could parse all config
properties at once and store them in an array. This would make it easier to
create drivers which do not function solely as callbacks from
pinctrl-generic.
This commit increases the size of the sandbox build by approximately 48
bytes. However, it also decreases the size of the K210 device tree by 2
KiB from the previous version of this series.
The documentation has been updated from the last Linux commit before it was
split off into yaml files.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
bloblist enhancement for alignment
Update ofnode/dev_read phandle function
sandbox keyboard enhancements and fixes
|
|
Reformat the command line options chapter so that the command line options
clearly stand out.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
|
|
Bring in the assorted changes that have been staged in the 'next' branch
prior to release.
Signed-off-by: Tom Rini <[email protected]>
|
|
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
This adds this dynamic switching right before booting Linux
and the configuration steps in the boards documentation.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
[narmstrong: fixed warning by replacing min() by min_t()]
|
|
- Generic UDP framework
- TFTP fixes
- dwc_eth_qos, smc911x, smc911x and mscc phy fixes
|
|
Some Espressobin boards got assigned more than one MAC address. Update
instructions how to correctly store and preserve all MAC addresses.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Andre Heider <[email protected]>
|
|
This commit adds a generic udp protocol framework in the
network loop. So protocol based on udp may be implemented
without modifying the network loop (for example custom
wait magic packet).
Signed-off-by: Philippe Reynes <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Dump SCMI DT bindings documentation from Linux kernel source
tree v5.8-rc1.
Signed-off-by: Etienne Carriere <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In the boot flow description add the RESET and BOOT button as well as the
function of the DTR and RTS lines of the serial interface.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The correct kflash parameter value for the Maix One Dock is "dan".
See:
https://github.com/sipeed/platform-kendryte210/blob/master/boards/sipeed-maix-one-dock.json#L22
Fixes: 137dc153fda9 ("doc: riscv: Update documentation for Sipeed MAIX boards")
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Add a description of how to flash Edison using the xFSTK tool.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
|
|
Some boards want to reserve extra regions of memory. Add a 'chosen'
property to support this.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Some devices can wake the system from sleep, e.g opening the lid on a
clamshell or moving a USB mouse.
Add a wake to specify this for USB devices and add the settings for Apollo
Lake.
Signed-off-by: Simon Glass <[email protected]>
|
|
Many I2C devices produce roughly the same ACPI data with just things like
the GPIO/interrupt information being different.
This can be handled by a generic driver along with some information in the
device tree.
Add a generic i2c driver for this purpose.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
Recent versions of Chrome OS do not have a kernel in the root disk, to
save space.
With the improvements to the 'zboot' command it is fairly easy to load
the kernel from the raw partition. Add instructions on how to do this.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Wolfgang Wallner <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
A few things have changed since this was written about 18 months ago.
Update the README.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Wolfgang Wallner <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add compatible string "gianfar" support and update the
device-tree-bindings doc.
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The install command is missing for an apt-get command.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Merge in v2020.10-rc5
|
|
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
[bmeng: correct one typo in the commit message]
Signed-off-by: Bin Meng <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
----------------------------------------------------------------
Fixes for 2020.10
-----------------
- Toradex boards
- mx6qsabrelite: fix env offset
- esdhc_imx: waiting for clock instead of sleep
- dyn RAM calibration for entry point i.MX6
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/728274602
|
|
The Toradex product is called apalis-imx8 consisting of SoM with
i.MX8QM and i.MX8QP SoCs.
Signed-off-by: Philippe Schenker <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: Philippe Schenker <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <[email protected]>
Patch-cc: Mario Six <[email protected]>
Patch-cc: Qiang Zhao <[email protected]>
Patch-cc: Holger Brunck <[email protected]>
Patch-cc: Madalin Bucur <[email protected]>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
END
|
|
Provide the settings for the debug UART on the QEMU ARM virt board.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The K3 J7200 SoCs have two dual-core Arm R5F clusters/subsystems, with
2 R5F cores each, one in each of the MCU and MAIN voltage domains.
These clusters are a revised version compared to those present on
J721E SoCs. Update the K3 R5F remoteproc bindings with the compatible
info relevant to these R5F clusters/subsystems on K3 J7200 SoCs.
Signed-off-by: Suman Anna <[email protected]>
|
|
Provide a description of the U-Boot build process with GCC in the HTML
documentation.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
