| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for programming of the StratixV FPGAs. Programming
is done in this case (board theadorable) via SPI. The board may provide
board specific code for bitstream programming.
This StratixV support will be used by the theadorable board.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Vagrant Cascadian <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Apparently, the logic for the FPGA global bit is not universal between Gen5
and Gen10 devices is not the same. Disabling this bit, while applicable to
Gen10 devices, will break FPGA programming on Gen5 devices.
Signed-off-by: Dinh Nguyen <[email protected]>
|
|
Check for substrings in deviceID validation check
so that it can support xa bitstreams also.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
We should be setting the FPGA Interface Group global bit that will correctly
disable all interfaces between the FPGA and HPS.
Signed-off-by: Dinh Nguyen <[email protected]>
|
|
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
In case the FPGA bitstream is aligned to 4 bytes, skip the
part of the assembler which handles unaligned bitstream.
Otherwise, that part will loop indefinitelly.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Dinh Nguyen <[email protected]>
|
|
Show fpga_op->info even if desc->iface_fns is not defined.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Ensure that operations are correctly setup.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
SPL needs to detect FPGA device which will be used
for loading bitstream.
Signed-off-by: Michal Simek <[email protected]>
|
|
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <[email protected]>
Acked-by: Simon Glass <[email protected]>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add code necessary to program the FPGA part of SoCFPGA from U-Boot
with an RBF blob. This patch also integrates the code into the
FPGA driver framework in U-Boot so it can be used via the 'fpga'
command.
Signed-off-by: Pavel Machek <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
V2: Move the not-CPU specific stuff into drivers/fpga/ and base
this on the cleaned up altera FPGA support.
|
|
Add a table of FPGA family with matching functions associated with
it and make all the code just look up the family in that table and
call the associated function instead of the horrible switch voodoo
which was duplicated all over the place.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
Acked-by: Pavel Machek <[email protected]>
|
|
Make the function return either 0 or -EINVAL, that is, normal
expected error codes and success codes instead of true/false
nonsense.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
Acked-by: Pavel Machek <[email protected]>
|
|
Move the function to the top of the file to avoid forward declaration.
No functional change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
Acked-by: Pavel Machek <[email protected]>
|
|
Further improve the indentation in the rest of the file, where
the indentation is initially a bit less brutal. There is no
functional change in this patch.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
Acked-by: Pavel Machek <[email protected]>
|
|
Boldly go, where no programmer has gone before and just clean up
the indentation mayhem. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
|
|
Clean up the printf() statements and get rid of the PRINTF()
macro by replacing it with debug_cond().
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
Acked-by: Pavel Machek <[email protected]>
|
|
Most of the warnings seem to be related to using 'int' for size_t. Change
this and fix up the remaining warnings and problems. For bootm, the warning
was masked by others, and there is an actual bug in the code.
Signed-off-by: Simon Glass <[email protected]>
|
|
Added support to load a bitstream image in chunks by reading it in
chunks from SD/MMC.
Command format:
loadfs [dev] [address] [image size] [blocksize] <interface>
[<dev[:part]>] <filename>
Example: fpga loadfs 0 1000000 3dbafc 4000 mmc 0 fpga.bin
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Do not do partial bitstream detection based on bitstream
size and use bitstream_type argument which is passed
from the fpga core.
Signed-off-by: Michal Simek <[email protected]>
|
|
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <[email protected]>
|
|
Use helper function zynq_validate_bitstream so that the
code can be reused easily for different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Use zynq_dma_xfer_init, zynq_align_dma_buffer,
zynq_dma_transfer helper function performing dma
transfers so that the code can be reused easily for
different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Warnings:
drivers/fpga/zynqpl.c:150:32: warning: Using plain integer as NULL pointer
drivers/fpga/zynqpl.c:152:16: warning: Using plain integer as NULL pointer
Signed-off-by: Michal Simek <[email protected]>
|
|
Connect FPGA version with appropriate operations
to remove huge switch-cases for every FPGA family.
Tested on Zynq. Spartan2/Spartan3/Virtex2 just compile test.
Signed-off-by: Michal Simek <[email protected]>
|
|
No functional changes.
Signed-off-by: Michal Simek <[email protected]>
|
|
No functional changes.
Signed-off-by: Michal Simek <[email protected]>
|
|
No functional changes.
Signed-off-by: Michal Simek <[email protected]>
|
|
No functional changes.
Signed-off-by: Michal Simek <[email protected]>
|
|
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Vineet Gupta <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Albert Aribaud <[email protected]>
Acked-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <[email protected]>
|
|
When ARCH_DMA_MINALIGN is greater than header size of the bit file, and buf is
not aligned, new_buf address became greater then buf_start address and the
load_word loop corrupts bit file data.
A work around is to decrease new_buf of ARCH_DMA_MINALIGN, it might corrupt data
before buf but permits to load correctly.
Signed-off-by: Stany MARCEL <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
- Descend into drivers/fpga/ only when CONFIG_FPGA=y
- Descend into drivers/bios_emulator only when CONFIG_BIOSEMU=y
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
DMA doesn't work when src is placed below 1MB limit.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Buffers must be cache and dma aligned.
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Some versions of the Zynq first stage boot loader enable PCAP loopback
during boot regardless of whether or not the boot image includes PL
configuration. This behavior only appears in certain boot modes (notably
QSPI boot). Attempting to configure the PL with the loopback bit set
will result in timeouts and will prevent successful configuration.
In order to avoid this problem, and to avoid dependency on the version
of the FSBL used to boot the system, ensure that the loopback enable bit
is cleared when loading the driver.
Signed-off-by: Soren Brinkmann <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
- Add support for zc7100 device.
- FPGA programming on few of the SOC(zc7100) takes more
than 1sec, hence increased the program time by 4sec to
sync' all soc's.
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Ensure that wrong bitstream won't be loaded
to current device.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
All fpga functions use devnum as int. Only fpga_loadbitstream
is using it as unsinged long dev.
This patch synchronize it.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
In bitstream decoding you can directly check device
which you want to load and in fpga.c are fpga_validate
and fpga_dev_info functions which should be used for it.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
CONFIG_FPGA in past was a bitfield where bits
were use for vendor identification.
This fix should be the part of this commit:
"Improve configuration of FPGA subsystem"
(sha1: 0133502e39ff89b67c26cb4015e0e7e8d9571184)
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
No functional changes.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <[email protected]>
|
|
Deassert the CONFIG pin before asserting it again. This assures that the
FPGA will be resetted and therefore configuration will be correctly
enabled.
This is also already done on other FPGA's, e.g. Stratix.
Signed-off-by: Stephan Gatzka <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Thomas Weber <[email protected]>
|
|
CONFIG_SYS_FPGA_PROG_FEEDBACK was already introduced to print
the current status of FPGA loading - an undef in the code made this
CONFIG_ useless.
Signed-off-by: Stefano Babic <[email protected]>
|
