| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for MediaTek I2C interface
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Weijie Gao <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
These two device tree properties were not being applied.
Fixes: 1fd9eb68d6 ("i2c: stm32f7: move driver data of each instance in a privdata")
Signed-off-by: Jorge Ramirez-Ortiz <[email protected]>
Reviewed-by: Alain Volmat <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Tested-by: Patrick Delaunay <[email protected]>
|
|
Current function stm32_i2c_message_xfer is sending a STOP
whatever the result of the transaction is. This can cause issues
such as making the bus busy since the controller itself is already
sending automatically a STOP when a NACK is generated.
Thanks to Jorge Ramirez-Ortiz for diagnosing and proposing a first
fix for this. [1]
[1] https://lore.kernel.org/u-boot/[email protected]/
Reported-by: Jorge Ramirez-Ortiz, Foundries <[email protected]>
Signed-off-by: Jorge Ramirez-Ortiz <[email protected]>
Signed-off-by: Alain Volmat <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Tested-by: Patrick Delaunay <[email protected]>
|
|
Functions stm32_i2c_message_start and stm32_i2c_handle_reload
both get a stop boolean indicating if the transfer should end with
a STOP or not. However no specific handling is needed in those
functions hence remove the parameter.
Signed-off-by: Alain Volmat <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Comment within stm32_i2c_message_start is misleading, indicating
that AUTOEND bit is setted while it is actually cleared.
Moreover, the bit is actually never setted so there is no need
to clear it hence get rid of this bit clear and the bit macro
as well.
Signed-off-by: Alain Volmat <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Bits should be set to 0, not 1.
Signed-off-by: Jorge Ramirez-Ortiz <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
The size of the dynamic stack allocation here is bounded by the if()
statement. However, just allocating the maximum size up-front and
doing malloc() if necessary avoids code duplication (the
i2c_setup_offset() until the invocation of ->xfer), and generates much
better (smaller) code:
bloat-o-meter drivers/i2c/i2c-uclass.o.{0,1}
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-144 (-144)
Function old new delta
dm_i2c_write 552 408 -144
Total: Before=3828, After=3684, chg -3.76%
It also makes static analysis of maximum stack usage (using the .su
files that are automatically generated during build) easier if there
are no lines saying "dynamic".
[This is not entirely equivalent to the existing code; this now uses
the stack for len <= 64 rather than len <= 63, but that seems like a
more natural limit.]
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
Add Nuvoton BMC NPCM750 i2c driver
Signed-off-by: Jim Liu <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
SCL direct drive mode prevents communication with devices that
do clock stretching, so disable. The Linux driver doesn't use
this mode, and the engine can handle clock stretching.
Signed-off-by: Eddie James <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Joel Stanley <[email protected]>
Reviewed-by: ryan_chen <[email protected]>
|
|
The stm32mp13 soc differs from the stm32mp15 in terms of
clear register offset for controlling the FMP (Fast Mode Plus).
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
As the migration deadline has passed, and all platforms have been
migrated, remove the non-DM code here.
Signed-off-by: Tom Rini <[email protected]>
|
|
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Joel Stanley <[email protected]>
Reviewed-by: Ryan Chen <[email protected]>
|
|
The reset control was written for the ast2500 and directly programs the
clocking register.
So we can share the code with other SoC generations use the reset device
to deassert the I2C reset line.
Signed-off-by: Joel Stanley <[email protected]>
Reviewed-by: Ryan Chen <[email protected]>
|
|
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Merge in v2022.07-rc5.
|
|
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Some of the DT compatibles have changed upstream so add new DT compatibles
to ensure things continue to keep working if the device trees are
updated.
Signed-off-by: Peter Robinson <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
s/actucal/actual/g
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add VPL versions of commonly used Kconfig options.
Signed-off-by: Simon Glass <[email protected]>
|
|
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
|
|
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.
This also has the added benefit of picking the right clock/reset
bits for H6 and new SoCs that have a rearranged PRCM MMIO space.
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Chips attached to the RSB bus require an initialization command before
they can be used. (Specifically, this command programs the chip's
runtime address.) The driver does this in its .probe_chip hook, under
the assumption that .probe_chip is called during child probe. This is
not the case; .probe_chip is only called by dm_i2c_probe, which is
intended for use by board-level code, not for chips with OF nodes.
Since this initialization command must be run before a child chip can be
used, do it before probing each child.
Signed-off-by: Samuel Holland <[email protected]>
Acked-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Chips attached to the P2WI bus require an initialization command before
they can be used. (Specifically, this switches the chip from I2C mode
to P2WI mode.) The driver does this in its .probe_chip hook, under the
assumption that .probe_chip is called during child probe. This is not
the case; .probe_chip is only called by dm_i2c_probe, which is intended
for use by board-level code, not for chips with OF nodes.
Since this initialization command must be run before a child chip can be
used, do it before probing each child.
Signed-off-by: Samuel Holland <[email protected]>
Acked-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.
Clean up the code in the process: remove #ifdefs and recognize that the
pin configuration is the same for all sun8i/sun50i SoCs, not just those
which select CONFIG_MACH_SUN8I.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Prepare v2022.04-rc5
|
|
Per dm_i2c_ops.probe_chip documentation, i2c_probe_chip() shall fallback
to default probe method when .probe_chip() returns -ENOSYS.
Signed-off-by: Nikita Yushchenko <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
During sequential loading of data, hold the bus to prevent controller
from sending stop signal in case no data is available in fifo.
Signed-off-by: Sai Pavan Boddu <[email protected]>
Reviewed-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/2407b39d305999cb42438c5423aebc3b514acabb.1646122610.git.michal.simek@xilinx.com
|
|
Start write transfer after loading data to FIFO.
Signed-off-by: Sai Pavan Boddu <[email protected]>
Reviewed-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f0b3e443daa7758e00dfdcc245cf6b2120b0e907.1646122610.git.michal.simek@xilinx.com
|
|
Avoid a race condition where read transaction is started
keeping expected bytes as 0. Which sometimes would result in sending
STOP signal as no data is expected. Observed on QEMU platform.
Signed-off-by: Sai Pavan Boddu <[email protected]>
Reviewed-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/487c8026791bfd60719403a2df2c54bb0ae99232.1646122610.git.michal.simek@xilinx.com
|
|
Per documentation, dm_i2c_ops.probe_chip() shall return -EREMOTEIO if
probe fails.
Currently, omap_i2c_probe_chip() returns 1 instead. Fix that.
Signed-off-by: Nikita Yushchenko <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
This seems to be very similar to the already existing PCA9547, save for
the fact that it supports 0.8V and doesn't support 5V. In fact, it is so
similar to the PCA9547 that the NXP LS1028A-RDB board has been driving
this chip using a "nxp,pca9547" compatible string.
Create a new compatible for the PCA9847 (which is the same as in Linux)
and define the same operating parameters for it as for PCA9547.
Cc: Heiko Schocher <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
|
|
This adds a compatible string for the Allwinner Sun4i-A10 I2C
controller. Without this, boards based on the R8 and A13 (at a
minimum) fail to boot.
Signed-off-by: Chris Morgan <[email protected]>
Acked-by: Akash Gajjar <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Sphinx expects Return: and not @return to indicate a return value.
find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Add compatible and data platform struct for sam9x60 SoC.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <[email protected]>
|
|
Testing on Armada XP with an EEPROM using register address with size
of 2 has shown, that the register address bytes are sent to the I2C
EEPROM in the incorrect order. This patch swabs the address bytes so
that the correct address is transferred to the I2C device.
BTW: This worked without any issues before migrating Armada XP to
DM I2C.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Samuel Holland <[email protected]>
Cc: Baruch Siach <[email protected]>
Cc: Pali Rohár <[email protected]>
Cc: Marek Behún <[email protected]>
Tested-by: Marek Behún <[email protected]>
|
|
Add I2C driver code for the Microchip PolarFire SoC.
This driver supports I2C data transfer and probe for I2C
slave addresses.
Signed-off-by: Padmarao Begari <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
- Turris MOX and Omnia changes, mostly moving to Kconfig (Marek)
- a37xx: pci: Misc smaller fixes (Pali)
- cmd: tlv_eeprom: Fix building with DEBUG enabled (Sven)
- termios_linux.h: Fix tcsendbreak() implementation (Pali)
- mvebu: Add missing "if SPL" (Tom)
|
|
Move the config option CONFIG_I2C_MV to a Kconfig option
CONFIG_SYS_I2C_MV and move the default definition from config header
files into defconfigs.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The following warning is seen in ocores_i2c.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_ptr().
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <[email protected]>
|
|
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.
There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
