| Age | Commit message (Collapse) | Author |
|---|
|
Caleb Connolly <[email protected]> says:
In Simon's series reworking autoprobe, a discussion came up about
DM_FLAG_PROBE_AFTER_BIND, specifically that it wasn't very clear where
this flag should be used.
This series implements my suggestions made there to clarify the use of
this flag, and fixup the two driver which erroneously apply it to their
driver struct (this does nothing).
Link: https://lore.kernel.org/u-boot/[email protected]/
Link: https://lore.kernel.org/r/[email protected]
|
|
Some drivers set DM_FLAG_PROBE_AFTER_BIND, this does nothing since it's
only every applied on a per-device basis.
Remove the flags.
Signed-off-by: Caleb Connolly <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Michal Simek <[email protected]>
|
|
This patch provides a driver for i.MX Messaging Unit (MU) using the
commom mailbox framework.
This is ported from Linux (v6.12.8) driver
drivers/mailbox/imx-mailbox.c. Its commit SHA is:
39d7d6177f0c ("mailbox: imx: use device name in interrupt name")
Signed-off-by: Viorel Suman <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
J722S R5 SPL uses sec-proxy threads 28 and 29 for communication with
TIFS. Mark these as valid threads in the driver.
https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j722s/sec_proxy.html
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Prasanth Babu Mantena <[email protected]>
Reviewed-by: Udit Kumar <[email protected]>
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
Add support for AMD Versal Gen 2. SoC is based on Cortex-a78ae 4 cluster/2
cpu core each. A lot of IPs are shared with previous families. There are
couple of new IP blocks where the most interesting from user point of view
is UFS.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/bc2b70831ce1031bd0fac32357bff84936e1310f.1716994063.git.michal.simek@amd.com
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
This function is a no-op. Remove it.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
As of now only one mailbox agent is supported by mailbox driver.
On zynqmp platform there are about 7 mailbox agents which can communicate
over same IPI channel to U-Boot. This patch series introduces new
"zynqmp_ipi_dest" driver which adds one to multi-channel mailbox
support.
Following format in device-tree is expected as per latest bindings:
zynqmp-ipi {
compatible = "xlnx,zynqmp-ipi-mailbox";
mbox_1: mailbox@1 {
/* New compatible for child node */
compatible = "xlnx,zynqmp-ipi-dest-mailbox";
...
};
...
mbox_n: mailbox@n {
compatible = "xlnx,zynqmp-ipi-dest-mailbox";
...
}
};
Then mailbox client uses child mailbox node as following:
ipi-dest-1 {
...
mboxes = <mbox_1 0>, <mbox_1 1>;
mbox-names = "tx", "rx";
...
};
New "zynqmp_ipi_dest" driver is for devices with
"xlnx,zynqmp-ipi-dest-mailbox" compatible string. This driver will take care
of mailbox send recv ops and it replaces previous "zynqmp_ipi" driver.
Now "zynqmp_ipi" driver simply binds each child device with "zynqmp_ipi_dest"
driver.
However, its important to maintain backward comaptibility with previous
bindings where child node does not have compatible string. In such case, new
driver isn't probed by U-Boot during boot and system fails to boot. To
resolve this issue firmware-zynqmp.c driver probes all the IPI parent node
driver which binds each child node device with "zynqmp_ipi_dest" driver.
This makes sure corresponding child driver will be
probed when requested using mbox_get_by_name or mbox_get_by_idx
framework calls.
This way multiple mailbox agents are supported in device-tree without breaking
previous binding support.
Signed-off-by: Tanmay Shah <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
If U-Boot is running in Exception Level 3 then use hardcode
register values for mailbox message passing with PMU.
This is only supported for zynqmp platform.
Signed-off-by: Tanmay Shah <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Use SMC calls to TF-A to operate IPI for execution level below 3. For
EL3 use hardcode IPI registers as TF-A isn't available in EL3.
Hence, in EL3 remote and local IPI ids retrieved using xlnx,ipi-id
property are unused.
Signed-off-by: Tanmay Shah <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Replace instances of http://www.ti.com with https://www.ti.com
Signed-off-by: Nishanth Menon <[email protected]>
|
|
A follow-up to commit 842fb5de424e
("drivers: use devfdt_get_addr_size_index_ptr when cast to pointer")
and commit 320a1938b6f7
("drivers: use devfdt_get_addr_index_ptr when cast to pointer").
In addition to using the *_ptr variants of these functions where the
address is cast to a pointer, this also changes devfdt_get_addr_*() to
dev_read_addr_*() in a few places. Some variable and field types are
changed from fdt_addr_t or phys_addr_t to void* where the cast was
happening later.
This patch fixes a number of compile warnings when building a 32bit
U-Boot with CONFIG_PHYS_64BIT=y. In some places, it also fixes error
handling where the return value of dev_read_addr() etc. was checked for
NULL instead of FDT_ADDR_T_NONE.
Signed-off-by: Matthias Schiffer <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The wrong field was checked.
Fixes: f9aa41023bd9 ("mailbox: Introduce K3 Secure Proxy Driver")
Signed-off-by: Matthias Schiffer <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
Sec proxy data buffer is 60 bytes with the last of the registers
indicating transmission completion. This however poses a bit of a
challenge.
The backing memory for sec_proxy is regular memory, and all sec proxy
does is to trigger a burst of all 60 bytes of data over to the target
thread backing ring accelerator. It doesn't do a memory scrub when
it moves data out in the burst. When we transmit multiple messages,
remnants of previous message is also transmitted which results in
some random data being set in TISCI fields of messages that have been
expanded forward.
The entire concept of backward compatibility hinges on the fact that
the unused message fields remain 0x0 allowing for 0x0 value to be
specially considered when backward compatibility of message extension
is done.
So, instead of just writing the completion register, we continue
to fill the message buffer up with 0x0 (note: for partial message
involving completion, we already do this).
This allows us to scale and introduce ABI changes back also work with
other boot stages that may have left data in the internal memory.
While at this, drop the unused accessor function.
Fixes: f9aa41023bd9 ("mailbox: Introduce K3 Secure Proxy Driver")
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Enable mailbox configs for Versal NET.
Signed-off-by: Jay Buddhabhatti <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/b3a9a6a58b74d17e2ec5f60617fa42062fbab951.1663589964.git.michal.simek@amd.com
|
|
Enable power domain driver to configure pmufw config object and request
node for all the IP's that are enabled in DT.
This driver depends on mailbox and IPI driver, hence enable them as well.
Add ARCH_VERSAL in the depends on of mailbox Kconfig to compile for
Versal platforms.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Mailbox driver might be need for Versal and other future platforms.
To remove the dependency, move struct zynqmp_ipi_msg to
zynqmp_firmware.h so that mailbox driver compiles for other platforms
easily.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This mailbox driver provides a communication channel with the
Apple IOP controllers found on Apple SoCs. These IOP controllers
are used to implement various functions such as the System
Manegement Controller (SMC) and NVMe storage. It allows sending
and receiving a 96-bit message over a single channel.
The header file with the struct used for mailbox messages is taken
straight from Linux.
Signed-off-by: Mark Kettenis <[email protected]>
Signed-off-by: Sven Peter <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested on: Macbook Air M1
Tested-by: Simon Glass <[email protected]>
|
|
Somewhere along the way, someone misspelt "invalid" and it got copied
everywhere. Fix it.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Alexander Dahl <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
R5 SPL would need to talk to DMSC using DM to DMSC sec-proxy threads.
Mark these as valid threads in the driver.
Signed-off-by: Vignesh Raghavendra <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
AM64x uses a different thread mapping that existing K3 SoCs, so update
the valid thread ID list to include those used for AM64x.
Also remove the comment identifying the purpose of each thread ID. The
purpose of the thread ID is specified when describing the threads in the
device tree and the same ID can mean different things on different SoCs,
so the comment is not useful.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <[email protected]>
|
|
In case of fpga loading (which can be huge) 100ms is not enough. That's why
extend timeout 10 times to wait maximum 1s to get ACK back.
Signed-off-by: Michal Simek <[email protected]>
|
|
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
dev needs to be gotten from mbox_chan
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Patrick Delaunay <[email protected]>
|
|
The most of drivers are using '_' instead of '-' in driver name. That's why
sync up these names to be aligned. It looks quite bad to see both in use.
It is visible via dm tree command.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Current IPI module register description is not align with IPI HW. The
registers with the wrong offset are not used so it does not cause real
issues. This patch aligns the register description.
Additionally comments added to explain why recv function does not check
any flag prior copying rx data.
Fixes: 660b0c77d816 ("mailbox: zynqmp: ipi mailbox driver")
Signed-off-by: Ibai Erkiaga <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing
changes made to 56d37f1c564107e27d873181d838571b7d7860e7.
Unfortunately this is causing CI failures:
https://travis-ci.org/github/trini/u-boot/jobs/711313649
Signed-off-by: Tom Rini <[email protected]>
|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Have this symbol follow the pattern of all other such symbols.
Signed-off-by: Trevor Woerner <[email protected]>
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <[email protected]>
|
|
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
ZynqMP mailbox driver implementing IPI communication with PMU. This would
allow U-Boot SPL to communicate with PMUFW to request privileged
operations.
Signed-off-by: Ibai Erkiaga <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
The following patch allows the mailbox node in DT to host subnodes with
mailbox definitions. If the client phandle to the mailbox is not the
mailbox driver node, just checks parents as well.
Signed-off-by: Ibai Erkiaga <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Check if request and free operations are present prior calling to the
functions.
Signed-off-by: Ibai Erkiaga <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
On STM32 family, the IPCC peripheral allows the communication
between 2 processors offering doorbells mechanism.
Signed-off-by: Fabien Dessenne <[email protected]>
Signed-off-by: Loic Pallardy <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Complete in the drivers directory the work started with
commit 83d290c56fab ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Add an option for building mailbox drivers within SPL.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Secure Proxy module manages hardware threads that are meant
for communication between the processor entities. Adding
support for this driver.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Signed-off-by: Andreas Dannenberg <[email protected]>
|
