| Age | Commit message (Collapse) | Author |
|---|
|
A patch for NAND uclass support was proposed about half a year ago:
https://patchwork.ozlabs.org/patch/722282/
It was not merged and I do not see on-going work for this.
Without DM-based probing, we need to set up pinctrl etc. in an ad-hoc
way and give lots of crappy CONFIG options for base addresses and
properties, which are supposed to be specified by DT. This is painful.
This commit just provides a probe hook to retrieve "reg" from DT and
allocate private data in a DM manner. This DT driver is not essentially
a NAND driver, in fact it is (ab)using UCLASS_MISC. Once UCLASS_NAND is
supported, it would be possible to migrate to it.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Staticize a few functions and variables which are no longer exposed.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
|
|
On some flash (like Macronix), QE (quad enable) bit is in the same
status register as BP# bits, and we need preserve its original value
during a reboot cycle as this is required by some platforms (like
Intel ICH SPI controller working under descriptor mode).
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
[Refined code for readability]
Signed-off-by: Jagan Teki <[email protected]>
|
|
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_NAND
Signed-off-by: Adam Ford <[email protected]>
[trini: Sync up a few more, add imply's]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add the print message to tell us why the erase operation doesn't work.
Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
This adds support for Macronix flash MX25U6435F (device ID 0xc22537).
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: Adam Ford <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This missing dependency has probably remained under the radar because
MTD_PARTITIONS is still whitelisted.
Signed-off-by: Karl Beldan <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Remove the ARCH_SUNXI dependency on selection of RBTREE.
Cc: Boris Brezillon <[email protected]>
Cc: Maxime Ripard <[email protected]>
Cc: Jagan Teki <[email protected]>
Signed-off-by: Karl Beldan <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <[email protected]>
CC: Fabio Estevam <[email protected]>
CC: Akshay Bhat <[email protected]>
CC: Ken Lin <[email protected]>
CC: Marek Vasut <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: "Sébastien Szymanski" <[email protected]>
CC: Christian Gmeiner <[email protected]>
CC: Stefan Roese <[email protected]>
CC: Patrick Bruenn <[email protected]>
CC: Troy Kisky <[email protected]>
CC: Nikita Kiryanov <[email protected]>
CC: Otavio Salvador <[email protected]>
CC: "Eric Bénard" <[email protected]>
CC: Jagan Teki <[email protected]>
CC: Ye Li <[email protected]>
CC: Peng Fan <[email protected]>
CC: Adrian Alonso <[email protected]>
CC: Alison Wang <[email protected]>
CC: Tim Harvey <[email protected]>
CC: Martin Donnelly <[email protected]>
CC: Marcin Niestroj <[email protected]>
CC: Lukasz Majewski <[email protected]>
CC: Adam Ford <[email protected]>
CC: "Albert ARIBAUD (3ADEV)" <[email protected]>
CC: Boris Brezillon <[email protected]>
CC: Soeren Moch <[email protected]>
CC: Richard Hu <[email protected]>
CC: Wig Cheng <[email protected]>
CC: Vanessa Maegima <[email protected]>
CC: Max Krummenacher <[email protected]>
CC: Stefan Agner <[email protected]>
CC: Markus Niebel <[email protected]>
CC: Breno Lima <[email protected]>
CC: Francesco Montefoschi <[email protected]>
CC: Jaehoon Chung <[email protected]>
CC: Scott Wood <[email protected]>
CC: Joe Hershberger <[email protected]>
CC: Anatolij Gustschin <[email protected]>
CC: Simon Glass <[email protected]>
CC: "Andrew F. Davis" <[email protected]>
CC: "Łukasz Majewski" <[email protected]>
CC: Patrice Chotard <[email protected]>
CC: Nobuhiro Iwamatsu <[email protected]>
CC: Hans de Goede <[email protected]>
CC: Masahiro Yamada <[email protected]>
CC: Stephen Warren <[email protected]>
CC: Andre Przywara <[email protected]>
CC: "Álvaro Fernández Rojas" <[email protected]>
CC: York Sun <[email protected]>
CC: Xiaoliang Yang <[email protected]>
CC: Chen-Yu Tsai <[email protected]>
CC: George McCollister <[email protected]>
CC: Sven Ebenfeld <[email protected]>
CC: Filip Brozovic <[email protected]>
CC: Petr Kulhavy <[email protected]>
CC: Eric Nelson <[email protected]>
CC: Bai Ping <[email protected]>
CC: Anson Huang <[email protected]>
CC: Sanchayan Maity <[email protected]>
CC: Lokesh Vutla <[email protected]>
CC: Patrick Delaunay <[email protected]>
CC: Gary Bisson <[email protected]>
CC: Alexander Graf <[email protected]>
CC: [email protected]
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Christian Gmeiner <[email protected]>
|
|
Currently the following build error is seen when a board using MMC SPL
is built and the MXS nand driver is also selected:
arch/arm/cpu/armv7/built-in.o: In function `arch_cpu_init':
arch/arm/cpu/armv7/mx6/soc.c:432: undefined reference to 'mxs_dma_init'
On mx6 the only user of mxs_dma_init() is the mxs nand driver, so
move it there.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Make make nand_info array static, since all direct users of nand_info array
have been converted to use get_nand_dev_by_index() API.
Signed-off-by: Grygorii Strashko <[email protected]>
|
|
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly
Signed-off-by: Grygorii Strashko <[email protected]>
|
|
nand_info is used all over the file so abstract it with
get_nand_dev_by_index() which will help for DM conversion.
Signed-off-by: Mugunthan V N <[email protected]>
Signed-off-by: Grygorii Strashko <[email protected]>
|
|
To set wait state, a hard coded value is used instead of using
latency parameter. stm32_flash_latency_cfg() is currently used
in arch/arm/mach-stm32/stm32f4/clock.c and in
drivers/clk/clk_stm32f7.c with, in both case, "5" as parameter.
Signed-off-by: Patrice Chotard <[email protected]>
|
|
commit dfe64e2c89731a3f9950d7acd8681b68df2bae03
Author: Sergey Lapin <[email protected]>
Date: Mon Jan 14 03:46:50 2013 +0000
mtd: resync with Linux-3.7.1
modified onenand_block_markbad to call mtd_block_markbad,
but as _block_markbad function pointer used by mtd_block_markbad
to do actual job is by default pointing back to
onenand_block_markbad there is no way this function ever
finishes its job.
Fix it by changing function body according current (4.12-rc6)
linux implementation.
Tested on IGEPv2 board with Muxed OneNAND(DDP) 512MB containing
several unerasable blocks this function marked bad.
Signed-off-by: Ladislav Michl <[email protected]>
|
|
Current implementation is unable to access second half of
DDP OneNAND flash (reads first half mirrored). Use block
and bufferram address calculations from onenand_base to
fix this.
Signed-off-by: Ladislav Michl <[email protected]>
|
|
Do not call onenand_spl_get_geometry() for each block read.
Signed-off-by: Ladislav Michl <[email protected]>
|
|
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the
associated topic_miamiplus.h header obsolete, so remove that as well.
Signed-off-by: Mike Looijmans <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This is not used anymore. Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Update this driver to support a live device tree.
Signed-off-by: Simon Glass <[email protected]>
|
|
Update the SPI flash uclass to support a live device tree.
Signed-off-by: Simon Glass <[email protected]>
|
|
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:
fdt_read_number
fdt_support_bus_default_count_cells
Signed-off-by: Simon Glass <[email protected]>
|
|
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <[email protected]>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <[email protected]>
|
|
Obtain NAND controller setup parameters from the device
tree instead of using hardcoded values.
Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Scott Wood <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
nand_spl_load_image implementation was copied over into three
different drivers and now with nand_spl_read_block used for
ubispl situation gets even worse. For now use least intrusive
solution and #include the same implementation to nand drivers.
Signed-off-by: Ladislav Michl <[email protected]>
Tested-by: Pau Pajuelo <[email protected]>
|
|
These drivers have no user since commit ea3310e8aafa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Michal Simek <[email protected]>
Acked-by: Jaehoon Chung <[email protected]>
|
|
Because there isn't the implementation of gpio_set/get_value()
and gpio_set/get_value() after the at91 gpio driver is converted
to support the driver model, use at91_set_gpio_value() and
at91_get_gpio_value()
Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Various commands to NAND flash results in the NAND flash becoming busy.
For those commands the SoC should wait until the NAND indicates it is
no longer busy before sending further commands. However, there is a delay
between the time the SoC sends its last command and when the NAND flash
sets its Ready/Busy Pin. This delay (tWB) must be respected or the SoC may
falsely assume the flash is ready when in reality it just hasn't had enough
time to indicate that it is busy.
Properly delaying by tWB is already done for nand_command/nand_command_lp
in nand_base.c including the version of it in the Linux kernel. Therefore,
this patch brings the handling of tWB delay inline to nand_base.c
Signed-off-by: Franklin S Cooper Jr <[email protected]>
[trini: Reformat comments slightly]
Signed-off-by: Tom Rini <[email protected]>
|
|
The SPL image needs to be built with a different ECC configuration than the
U-Boot binary.
Add Kconfig options with defaults to provide a value that should work for
anyone, but is still configurable if needs be.
Signed-off-by: Maxime Ripard <[email protected]>
Acked-by: Boris Brezillon <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Acked-by: Scott Wood <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
The default U-Boot offset for the Allwinner SoCs was set to 32kB.
This was probably to try to maintain some compatibility with the current
image that we build for the MMC where the U-Boot binary is also located at
a 32kB offset.
However, this causes a number of issues. The first one is that it prevents
us from using a backup SPL entirely, which is troublesome in case where the
first would be corrupt (especially on MLC which have a higher number of
bitflips).
We also cannot use the original MMC image on the NAND, because we need to
prepare the SPL image to include the ECCs and randomizer settings, which
reduces the interest of setting it at that particular offset.
It also prevents us from upgrading and flashing the U-Boot and SPLs
independantly, since it's very likely that it will fall in the same erase
block.
Since that default wasn't used by any board, change it for 8MB, which will
be in an erase block of its own, all the erase blocks being multiple of
two. The highest erase block size we encountered is 4MB, which means that
in this particular setup, the first and second erase blocks will be for the
SPL and its backup, and the third for U-Boot.
Signed-off-by: Maxime Ripard <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
We'll need that symbol so that the default offset are defined
Signed-off-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Expose the RBTREE feature through Kconfig and select this option from the
MTD_UBI option.
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Acked-by: Jagan Teki <[email protected]>
[Rebased on master]
Signed-off-by: Jagan Teki <[email protected]>
|
|
When trying to autodetect the ECC and randomization configurations, the
driver starts with a randomization disabled and no seeds.
In this case, the number of seeds is obviously 0, and the randomize boolean
is set to false.
However, the logic that retrieves the seed for a given page offset will
blindly use the number of seeds, without testing if the randomization is
enabled, basically doing a modulo by 0.
As it turns out, the libgcc in the common toolchain returns 0 here, which
was our expected value in such a case, and why we would not detect it.
However, U-Boot's libgcc will for some reason return from the function
instead, resulting in an error to load the U-Boot binary in the SPL.
Signed-off-by: Maxime Ripard <[email protected]>
Acked-by: Boris Brezillon <[email protected]>
Acked-by: Scott Wood <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
trini: Disable CONFIG_SPL_USE_ARCH_MEMSET on orangepi_2
Signed-off-by: Tom Rini <[email protected]>
|
|
The architecture is currently unmaintained, remove.
Cc: Benjamin Matthews <[email protected]>
Cc: Chong Huang <[email protected]>
Cc: Dimitar Penev <[email protected]>
Cc: Haitao Zhang <[email protected]>
Cc: I-SYST Micromodule <[email protected]>
Cc: M.Hasewinkel (MHA) <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Martin Strubel <[email protected]>
Cc: Peter Meerwald <[email protected]>
Cc: Sonic Zhang <[email protected]>
Cc: Valentin Yakovenkov <[email protected]>
Cc: Wojtek Skulski <[email protected]>
Cc: Wojtek Skulski <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
|
|
Addresses passed on to readl and writel are expected to be of the same
size as a pointer. Change the parameter types of sunxi_spi0_read_data()
to make the compiler happy and allow a warning-free aarch64 compile.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Simon Glass <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add initialization flag to avoid initializing NAND Flash multiple
times, otherwise it will calculate a wrong total size.
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).
Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.
Signed-off-by: Andrey Yurovsky <[email protected]>
|
|
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <[email protected]>
|
