| Age | Commit message (Collapse) | Author |
|---|
|
On i.MX6SX, 6UL and 7D, there are two enet controllers each has a
MDIO port. But Some boards share one MDIO port for the two enets. So
introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate
the MDIO port for sharing.
In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter
the CONFIG_FEC_MXC_MDIO_BASE.
To i.MX28, adapt to use the new config
Signed-off-by: Peng Fan <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Cc: Fabio Estevam <[email protected]>
|
|
This converts CONFIG_DRIVER_TI_CPSW to Kconfig
Signed-off-by: Alex Kiernan <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Migrate the CONFIG_TSEC_ENET option to Kconfig.
Signed-off-by: Mario Six <[email protected]>
|
|
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.
Signed-off-by: Christophe Leroy <[email protected]>
|
|
Add configurations for PFE.
Signed-off-by: Calvin Johnson <[email protected]>
Signed-off-by: Anjaneyulu Jagarlmudi <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Although Xilinx Zynq SoC was using MACB similar hardware. However,
U-boot MACB driver was not supporting Xilinx Zynq SoC. This patch is
to add support for the Xilinx Zynq SoC to the existing MACB network
driver.
This patch is to add Zynq GEM DMA Config, provide callback
function for different linkspeed for case of using Xilinx Zynq
Programmable Logic as GMII to RGMII converter.
This patch convert the return value to use error codes.
Signed-off-by: Wilson Lee <[email protected]>
Cc: Chen Yee Chew <[email protected]>
Cc: Keng Soon Cheah <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Wenyou Yang <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
|
|
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part
Signed-off-by: Ahmed Mansour <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Until now, Armada 3700 SoCs could not enable the mvneta driver, and thus
did not benefit from Ethernet support. Add ARMADA_3700 in the
"depends on" list of the MVNETA Kconfig entry.
Signed-off-by: Miquel Raynal <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.
Signed-off-by: Stefan Mavrodiev <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h,
likely missed in:
commit 3146f0c017df ("Move PHYLIB to Kconfig")
Signed-off-by: Artturi Alm <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
CONFIG_SMC911X
CONFIG_SMC911X_BASE
CONFIG_SMC911X_16_BIT
CONFIG_SMC911X_32_BIT
Signed-off-by: Adam Ford <[email protected]>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
move to Kconfig:
CONFIG_BCM_SF2_ETH
CONFIG_BCM_SF2_ETH_DEFAULT_PORT
CONFIG_BCM_SF2_ETH_GMAC
Also modified defconfigs of all platforms that use these configs.
Signed-off-by: Suji Velupillai <[email protected]>
Tested-by: Suji Velupillai <[email protected]>
Reviewed-by: JD Zheng <[email protected]>
Reviewed-by: Scott Branden <[email protected]>
Signed-off-by: Steve Rae <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Christophe Leroy <[email protected]>
|
|
This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file
Signed-off-by: Philipp Tomsich <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Move FTMAC100 to where it should be, alphabetically in
drivers/net/Kconfig
Signed-off-by: Tom Rini <[email protected]>
Conflicts:
drivers/net/Kconfig
|
|
Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
Boot linux kernel via dhcp and bootm ok.
NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4899 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'boomimage-310y-ae300-spi.bin'.
Load address: 0x600000
Loading: #################################################################
#################################################################
#################################################################
...
...
###################################
233.4 KiB/s
done
Bytes transferred = 13872076 (d3abcc hex)
NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4592 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'ae300.dtb'.
Load address: 0x2000000
Loading: #
82 KiB/s
done
Bytes transferred = 2378 (94a hex)
NDS32 # bootm 0x600000 - 0x2000000
Image Name:
Created: 2017-03-22 6:52:03 UTC
Image Type: NDS32 Linux Kernel Image (uncompressed)
Data Size: 13872012 Bytes = 13.2 MiB
Load Address: 0000c000
Entry Point: 0000c000
Verifying Checksum ... OK
Booting using the fdt blob at 0x2000000
Loading Kernel Image ... OK
Loading Device Tree to 01efc000, end 01eff949 ... OK
Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
#293 PREEMPT Wed Mar 22 14:49:28 CST 2017
CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: rick <[email protected]>
|
|
Add driver for the Renesas Ethernet AVB block found in RCar H3/M3.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Hiroyuki Yokoyama <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Joe Hershberger <[email protected]>
Based on work of:
Hiroyuki Yokoyama <[email protected]>
Takeshi Kihara <[email protected]>
Kazuya Mizuguchi <[email protected]>
|
|
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.
Signed-off-by: Mylène Josserand <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.
Signed-off-by: Mylène Josserand <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
Move the SUNXI_GMAC config option to Kconfig, remove it
from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC.
Signed-off-by: Mylène Josserand <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
Since Armada 7K/8K is also equipped with a newer version of the MVPP2
ethernet controller, lets enable compilation of this driver for these
platforms.
Signed-off-by: Stefan Roese <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.
BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).
Signed-off-by: Alexandru Gagniuc <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Add CONFIG_MACB option in KConfig to be used to select the Cadence
MACB Ethernet driver.
Signed-off-by: Wenyou Yang <[email protected]>
|
|
Add a new driver for the GMAC ethernet interface present in Rockchip
RK3288 SOCs. This driver subclasses the generic design-ware driver to
add the glue needed specifically for Rockchip.
Signed-off-by: Sjoerd Simons <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Romain Perier <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <[email protected]>
|
|
This driver supports the Synopsys Designware Ethernet QoS (Quality of
Service) a/k/a eqos IP block, which is a different design than the HW
supported by the existing designware.c driver. The IP supports many
options for bus type, clocking/reset structure, and feature list. This
driver currently supports the specific configuration used in NVIDIA's
Tegra186 chip, but should be extensible to other combinations quite
easily, as explained in the source.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Simon Glass <[email protected]> # V1
Acked-by: Joe Hershberger <[email protected]>
|
|
Added kconfig for FEC_MXC driver.
Cc: Joe Hershberger <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Signed-off-by: Zubair Lutfullah Kakakhel <[email protected]>
Reviewed-by: Paul Burton <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the
only board configuration that uses it and put it into that board's
defconfig.
Cc: Stefan Kristiansson <[email protected]>
Signed-off-by: Max Filippov <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).
BIG Thanks to Andre for providing some of the DT code.
Signed-off-by: Amit Singh Tomar <[email protected]>
Acked-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Add ethernet driver for the AR933x and AR934x Atheros MIPS machines.
The driver could be easily extended to other WiSoCs.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Wills Wang <[email protected]>
[fixed Kconfig dependency]
Signed-off-by: Daniel Schwierzeck <[email protected]>
|
|
This patch adds support for the mvpp2 ethernet controller which is integrated
in the Marvell Armada 375 SoC. This port is based on the Linux driver (v4.4),
which has been stripped of the in U-Boot unused portions.
Tested on the Marvell Armada 375 eval board db-88f6720.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Luka Perkov <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.
This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.
There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
Signed-off-by: Michael Haas <[email protected]>
Tested-by: Karsten Merker <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <[email protected]>
|
|
This driver implements MAC and MII layer of the ethernet controller.
Network data transfer is handled by controller internal DMA engine.
Ethernet controller is configurable through device-tree file.
Signed-off-by: Purna Chandra Mandal <[email protected]>
|
|
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Also add dependency on PHYLIB and MII which is required.
Clean PHYLIB dependency from the driver too.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.
This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.
Signed-off-by: Thomas Chou <[email protected]>
Reported-by: Pavel Machek <[email protected]>
Acked-by: Chin Liang See <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Tested-by: Pavel Machek <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Clear driver dependecies via Kconfig. Remove PHYLIB dependency from
the driver.
Signed-off-by: Michal Simek <[email protected]>
|
|
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add Kconfig option in preparation for moving board to use Kconfig.
Signed-off-by: Bin Meng <[email protected]>
|
|
Add Kconfig options in preparation for moving boards to use Kconfig.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <[email protected]>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <[email protected]>
|
