| Age | Commit message (Collapse) | Author |
|---|
|
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.
This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.
There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
Signed-off-by: Michael Haas <[email protected]>
Tested-by: Karsten Merker <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <[email protected]>
|
|
This driver implements MAC and MII layer of the ethernet controller.
Network data transfer is handled by controller internal DMA engine.
Ethernet controller is configurable through device-tree file.
Signed-off-by: Purna Chandra Mandal <[email protected]>
|
|
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Also add dependency on PHYLIB and MII which is required.
Clean PHYLIB dependency from the driver too.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.
This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.
Signed-off-by: Thomas Chou <[email protected]>
Reported-by: Pavel Machek <[email protected]>
Acked-by: Chin Liang See <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Tested-by: Pavel Machek <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Clear driver dependecies via Kconfig. Remove PHYLIB dependency from
the driver.
Signed-off-by: Michal Simek <[email protected]>
|
|
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add Kconfig option in preparation for moving board to use Kconfig.
Signed-off-by: Bin Meng <[email protected]>
|
|
Add Kconfig options in preparation for moving boards to use Kconfig.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <[email protected]>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <[email protected]>
|
|
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <[email protected]>
Version 1:
Acked-by: Joe Hershberger <[email protected]>
|
|
Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host
machine's network interface.
This raw Ethernet API requires elevated privileges. You can either run
as root, or you can add the capability needed like so:
sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot
Signed-off-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
First just add support for MAC drivers.
Signed-off-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
