| Age | Commit message (Collapse) | Author |
|---|
|
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Split the driver into common and non-DM functionality, so that the
DM support can later re-use the common code, while we retain the
non-DM code until all the platforms are converted.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Instead of always calling rtl8139_eeprom_delay() with priv->ioaddr,
call it with priv and let the function access priv->ioaddr. This
reduces code duplication and has no impact, since the compiler will
inline this as needed anyway.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Introduce rtl8139_pdata, which is a super-structure around eth_device
and tracks per-device state, here the device IO address, PCI BDF, RX
and TX ring position. Pass this structure around instead of the old
non-DM eth_device in preparation for DM conversion.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
These macros depended on the dev variable being declared wherever
they were used. This is wrong and will not work with DM anyway, so
pass only the PCI BFD into these macros, which fixes the dependency
and prepares them for DM support as well.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Replace the use of custom static ioaddr variable with common dev->iobase,
no functional change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Replace malloc()+memset() combination with calloc(), no functional change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Pull the device name setting into a separate function, as this
will be shared between DM/non-DM variants.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Add the DP8382X generic PHY registration to the TI PHY init file.
Acked-by: Michal Simek <[email protected]>
Signed-off-by: Dan Murphy <[email protected]>
|
|
ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.
In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.
Acked-by: Michal Simek <[email protected]>
Signed-off-by: Dan Murphy <[email protected]>
|
|
There are devices accesible through mdio clause-45, such as
retimers, that do not have PMA or PCS blocks.
This patch adds MDIO_MMD_VEND1 on the list of device addresses
where phyid is searched. Previous order of devices was kept.
Signed-off-by: Florin Chiculita <[email protected]>
Reviewed-by: Madalin Bucur <[email protected]>
|
|
This is a WAR for DHCP failure after rebooting from the L4T kernel. The
r8169.c kernel driver is setting bit 19 of the rt816x HW register 0xF0,
which goes by FuncEvent and MISC in various driver source/datasheets.
That bit is called RxDv_Gated_En in the r8169.c kernel driver. Clear it
here at the end of probe to ensure that U-Boot can get an IP assigned
via DHCP.
Signed-off-by: Tom Warren <[email protected]>
|
|
Linux commit 232ba3a51cc2 ('net: phy: Micrel KSZ8061: link failure after
cable connect') implements a fix for the above errata.
This patch replicates that errata fix in an ksz8061 specific init routine.
Signed-off-by: Bryan O'Donoghue <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
- DM_ETH support for P2041RDB, T1024RDB, P5040DS, P3041DS, P4080DS, bug
fixes
- Add TBI PHY access through MII
- DDR: Rework errata workaround for A008109, A008378, 009942
|
|
When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.
Fixes: 9a1d6af55ecd ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Tested-by: Vladimir Oltean <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Tested-by: Vladimir Oltean <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Compilation error occur when DM_ETH is enabled without DM_PCI.
Signed-off-by: Madalin Bucur <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The H6 EMAC is very similar to the H3 variant, except that it uses the
same pinmux as R40. Add support for it.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
While the R40 uses a different register for EMAC clock configuration
than other chips, the register has a very similar layout. Reuse the
existing bitfield definitions in this file, since they match.
This allows the driver to compile on the H6 platform, where the
CCM_GMAC_CTRL definitions are not present.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Add support for U-Boot DM and DT probing.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat. It is however necessary to cache RXFC value, because
reading that one out clears it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Fix various checkpatch complaints.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
There is only one chip ID in the table of chip IDs for this chip.
Read out the chip ID instead and mask off the last "revision" bit
to check the chip ID, this works for all chips in the family. Then
drop the chip ID passing around.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
The packet status and length information should be extracted from the
FIFO per-packet. Adjust the code such that it reads the packet meta
data and then the packet afterward, if applicable.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Most of the entries in the structure are useless, remove them. Inline
the rest of uses where applicable.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Per KS8851-16MLL, the RXQCR is a 16bit register. Use 16bit accessors
to it consistently and drop the ks_wrreg8() function altogether, as
it is not used anymore.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
The cached RXQCR value is never updated, remove the cache and just use
the bits in the cache directly in the code.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced. Moreover, remove
printf() in the fail path, as it is useless, and return proper -ENOMEM
return code.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
|
|
The DPC fixup for MAC address and enet_if is not made if
/board/ports node is missing in DPC file.
Add /board/ports or /ports nodes if them are missing.
Signed-off-by: Razvan Ionut Cirjan <[email protected]>
Reviewed-by: Ioana Ciornei <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Similarly to iommu-map, the msi-map property must also be fixed up
in the device tree, in order for the icid -> streamid translation
be possible in the MSI case as well.
Signed-off-by: Laurentiu Tudor <[email protected]>
Reviewed-by: Diana Craciun <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Bus callback functions for read/write/reset need to be set only for
DM_ETH, moving endif a bit lower.
Signed-off-by: Madalin Bucur <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Fix up some incorrect code style in calls to functions in the linux/time.h
header, mostly udelay().
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <[email protected]>
|
|
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <[email protected]>
Signed-off-by: Trevor Woerner <[email protected]>
|
|
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <[email protected]>
|
|
As per Linux's driver, ID_MODE_DIS is only set when the PHY interface is
RGMII. Don't enable it for the rest of setups.
This has been seen to misconfigure RPi4's PHY when booting Linux.
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Fix boot issues on Nokia RX-51
- Configure AM6 CPSW for 10Mbps in rgmii mode.
- Minor changes for J721e
|
|
Implement the read_rom_hwaddr callback to load MAC address from fuse
for imx8m platforms.
Reviewed-by: Fugang Duan <[email protected]>
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
