| Age | Commit message (Collapse) | Author |
|---|
|
The Ethernet MAC used in newer Allwinner SoCs (H3, A64, H5) got an
upstream Linux driver in v4.15.
This one uses a slightly different binding from the original one used
by the U-Boot driver.
The differences to the old binding are:
- The "syscon" address is held in a separate node, referenced via a
phandle in the "syscon" property.
- The reference to the PHY is held in a property called "phy-handle",
not "phy".
- The PHY register is at offset 0x30 in the syscon device, not at 0.
- The internal PHY is activated when the node, which phy-handle points
to, is a child node of an "allwinner,sun8i-h3-mdio-internal" node.
Teach the U-Boot driver how to find its resources in a "new-style" DT,
so that we can use a Linux kernel compatible DT for U-Boot as well.
This keeps support for the old binding for now, to allow a smooth
transition.
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
The Linux kernel driver for the Allwinner pin controller gained support
for generic properties, which are now also used in the DTs.
The sun8i-emac Ethernet driver for new Allwinner MACs reads the pins from
the DT, but so far only supported the old binding.
Update the parsing routine to cope with both the old and new bindings,
so that the newer DTs can be used with U-Boot and its Ethernet driver.
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
This patch bypasses phy detection logic for GMII interface
and just depend on phy address received from DT. This patch
is required as phy detection logic is different for some phys
like xilinx phy which can be connected over SGMII and GMII
interface.
This fixes the issue of ethernet failures when xilinx phy is
connected over GMII interface.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Last user of this driver went away in October 2014 in
commit d58a9451e7339ed4 ("ppc/arm: zap EMK boards").
Signed-off-by: Tuomas Tynkkynen <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
In
if (a > =0) {...}
else (a < 0) {...}
the second logical constraint is superfluous.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
In
int ret = A;
ret = B;
the first assignment has not effect.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Current Cortina phy driver assumes that firmware upload
is required during initialization and is dependent
on presence of corresponding macros like CONFIG_CORTINA_FW_ADDR
for compilation.
But Cortina phy has provision to store phy firmware in
attached dedicated EEPROM. And boards designed with such
EEPROM does not require firmware upload.
Add CORTINA_NO_FW_UPLOAD option in cortina.c to support
such boards.
Signed-off-by: Priyanka Jain <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Update get_phy_id() implementation in cortina.c to check
for Cortina_phy by comparing device phy_id with cortina phy_id
instead of relying on presence of CORTINA macros.
This will allow get_phy_id to work with non-cortina phy devices
which might have same phy address as Cortina device but on
different bus.
Signed-off-by: Priyanka Jain <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Add configurations for PFE.
Signed-off-by: Calvin Johnson <[email protected]>
Signed-off-by: Anjaneyulu Jagarlmudi <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
pfe_command provides command line support for several features that
support pfe, like starting or stopping the pfe, checking the health
of the processor engines and checking status of different units inside
pfe.
Signed-off-by: Calvin Johnson <[email protected]>
Signed-off-by: Anjaneyulu Jagarlmudi <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This patch adds PFE driver to U-Boot
Following are the main driver files:-
pfe_hw.c: provides low level helper functions to initialize PFE
internal processor engines and other hardware blocks
pfe_driver.c: provides initialization functions
and packet send and receive functions
pfe_eth.c: provides high level gemac initialization functions
pfe_firmware.c: provides functions to load firmware into PFE
internal processor engines.
pfe_mdio.c: provides functions to initialize phy and mdio.
Signed-off-by: Calvin Johnson <[email protected]>
Signed-off-by: Anjaneyulu Jagarlmudi <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
With CONFIG_DM_ETH enabled, aquantia driver compilation fails with
below error. This patch fixes the issue by including dm.h.
drivers/net/phy/aquantia.c: In function ‘aquantia_startup’:
drivers/net/phy/aquantia.c:73:21: error: dereferencing pointer to
incomplete
type ‘struct udevice’
phydev->dev->name);
^~
Signed-off-by: Calvin Johnson <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
After allocating plat the pointer is checked.
Afterwards name is allocated and not checked.
Add the missing check to avoid a possible NULL dereference.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.
Signed-off-by: Kyle Evans <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).
Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.
After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.
- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.
- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.
After the changes the suspicious defconfigs passes building.
Signed-off-by: Stefan Mavrodiev <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
The previous code tried to update the PHY parameters without waiting for
autonegotiation to complete. This caused wrong values to be written to
the EMAC in sun8i_adjust_link(). As a result, any commands that called
eth_start() before autonegotiation completed would find the network
nonfunctional. Fix this by using the correct function to start up the
PHY.
Signed-off-by: Samuel Holland <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
|
|
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add entries for the R8A77965 M3N SoC.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Arno Steffens <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Fix commit f1bcad22dd19 ("net: e1000: add support for writing to
EEPROM").
Signed-off-by: Bernhard Messerklinger <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
After commit ba1f966725223 ("net: designware: add clock support")
we got NET broken on axs101 and axs103 platforms.
Some clock don't support gating so their clock drivers don't
implement .enable/.disable callbacks. In such case clk_enable
returns -ENOSYS.
Also some clock drivers implement .enable/.disable callbacks not for all
clock IDs and return -ENOSYS (or -ENOTSUPP) for others.
If we have such clock in 'clocks' list of designware ethernet controller
node we fail to probe designware ethernet.
Fix it.
Signed-off-by: Eugeniy Paltsev <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
Fix some style violations in the generic PHY management code.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Mario Six <[email protected]>
|
|
Commit 68e6ecadc551 ("net: phy: marvell 88e151x: Fix handling of RGMII
interface types") fixed the initialization of 88e151x phys, but made it
so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX
delay bits cleared. The default (like in m88e1111s_config) is to have
both bits set.
Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII
case so that both bits are set.
Signed-off-by: Mario Six <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Fix some style violations (mostly wrong indentions) in the Marvell PHY
driver.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Mario Six <[email protected]>
|
|
Make the tsec ethernet driver compatible with a live device tree.
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Mario Six <[email protected]>
|
|
tsec_initialize allocates a private driver structure using malloc.
Should the memory allocation of this private structure fail, the
function execution is aborted with a return 0, but the previously
allocated device structure is never freed, hence leaked.
Free the device structure in the error case.
Signed-off-by: Mario Six <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Signed-off-by: Mario Six <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
ll_temac driver was used by Xilinx Microblaze big endian and
Xilinx ppc405/ppc440 SoCs.
ppc support was removed by: "powerpc: remove 4xx support"
(sha1: 98f705c9cefdfdba62c069821bbba10273a0a8ed)
and Microblaze BE is not tested for a long time that's why this driver
can be removed because none is going to updated it to DM anyway.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Drop the whole map/unmap_physmem stuff and just use the address
already obtained from DT in ofdata_to_platdata(), instead of
repeating that, wrongly, in probe.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Fix minor checkpatch warning about udelay(3000) being too long
and should be replaced by mdelay(3).
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Drop the len variable, it's useless.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Inline this variable which is quite useless.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
There is no value to enable phylib without networking support.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Implement programming MAC address to the hardware, i.e. external flash
seen as EEPROM.
MAC address is only written if it differs from what is already stored in
flash or if reading the current MAC address fails.
Signed-off-by: Hannu Lounento <[email protected]>
CC: Joe Hershberger <[email protected]>
Signed-off-by: Martyn Welch <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Split the implementation of e1000_read_mac_addr into eeprom and register
versions called by e1000_read_mac_addr.
This allows for calling e1000_read_mac_addr when MAC address is needed
with no constraints where it is read from, and for calling the register
and, especially, the eeprom version directly in order to specify where
to read the address from.
Signed-off-by: Hannu Lounento <[email protected]>
CC: Joe Hershberger <[email protected]>
Signed-off-by: Martyn Welch <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Port functions for writing to EEPROM, updating the checksum and
committing data to flash from the Linux kernel igb driver.
Functions were ported from Linux 4.8-rc2 (694d0d0bb20).
Signed-off-by: Hannu Lounento <[email protected]>
CC: Joe Hershberger <[email protected]>
Signed-off-by: Martyn Welch <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
When building for 64bits system, we get some warnings about type
cast between pointer and integer. This patch eliminates the warnings
by using ulong/long type which is 32bits on 32bits system or 64bits on
64bits system.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The MIB RAM and FIFO receive start register does not exist on
i.MX8M. Accessing these register will cause system hang.
Signed-off-by: Peng Fan <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
|
|
For for case of lazyapply method, API fdt_fixup_board_enet() gets
invoked before DPL being deployed. This leads to an issue that
fsl-mc fdt fixup status marked as fail and dprc driver didn't get
registered in linux boot.
Fixes this issue by calling fdt_fixup_board_enet() for case when
DPL is deployed successfully in lazyapply method.
Signed-off-by: Yogesh Gaur <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
When we have a driver that is used on both 32bit and 64bit targets and
we are talking about address space we cannot use u64 nor u32 and instead
need to use phys_addr_t.
Fixes: 377883f16d36 ("net: mvpp2x: fix phy connected to wrong mdio issue")
Cc: Stefan Chulski <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
The GMAC in the RK3228 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <[email protected]>
Acked-by: Philipp Tomsich <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
The GMAC2IO in the RK3328 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3328-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <[email protected]>
Acked-by: Philipp Tomsich <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
The rv1108 GMAC only support rmii interface, so need to add the
set_rmii() ops. Use the phy current interface to set rmii or
rgmii ops. At the same time, need to set the mac clock rate of
rmii with 50M, the clock rate of rgmii with 125M.
Signed-off-by: David Wu <[email protected]>
Acked-by: Philipp Tomsich <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
|
|
Add DM capable code into the SH ethernet driver and support probing
both from DT and pdata. The legacy non-DM, non-DT support is retained
as there are still systems in the tree which are not DM or DT capable.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Move the legacy functions around, so that they can be wrapped in a
massive ifdef CONFIG_DM_ETH once DM support is added. No functional
change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
|
Split sh_eth_init() function into smaller chunks, which can
be called from both DM and non-DM code while handling the
specifics of both configurations.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Joe Hershberger <[email protected]>
|
