| Age | Commit message (Collapse) | Author |
|---|
|
Support is added for 5 new Qualcomm SoCs:
* QCM2290 and SM6115 are low and mid range SoCs used on the RB1 and RB2
respectively. SM6115 is also used in some mid-range smartphones/tablets.
Initial support includes buttons and USB (host and gadget).
* SM8250 is a flagship SoC from 2020 used on the RB5, as well as many flagship
smartphones. The board can boot to a U-Boot prompt, but is missing regulators
necessary for USB support.
* SM8550, and SM8650 are flagship mobile SoCs from 2023 and 2024
respectively. Found on many high end smartphones.
In addition:
* Support is added for the Schneider HMIBSC board.
* mach-snapdragon switches to OF_UPSTREAM
* IPQ40xx gets several regressions fixed and some overall cleanup.
* The MSM serial driver gains the ability to generate the bit-clock
automatically, no longer relying on a custom DT property.
* The Qualcomm SMMU driver gets a generic compatible (so per-SoC compatibles
don't need to be added).
* Support for the GENI I2C controller is added.
* The qcom SPMI driver has SPMI v5 support fixed, and v7 support added.
* The qcom sdhci driver gets some fixes for SDCC v5 support.
* SDM845 gains sdcard support
* Support is added for the Synopsys eUSB2 PHY driver (used on SM8550 and SM8650)
* SYS_INIT_SP_BSS_OFFSET is set to 1.5M to give us more space for FDTs.
* RB2 gets a work-around to fix the USB dr_mode property before booting Linux.
|
|
Add GPIO pinctrl function to enable driving GPIO pins as output low or
high.
Signed-off-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add support for driving the GPIO pins as output low or high.
Signed-off-by: Sumit Garg <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
SE HMIBSC board uses UART1 as the main debug console, so add
corresponding clocks and pinmux support. Along with that update
instructions to enable clocks for debug UART support.
Reviewed-by: Caleb Connolly <[email protected]>
Signed-off-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Currently, IPQ4019 pinctrl driver supports only a very limited number of
pin functions and is not fully DT compatible with Linux pinctrl nodes.
IPQ40xx SoC-s sometimes use different pin function numbers for the same
function depending on the pin number, so for example I2C0 on GPIO58 uses
function number 3 while on GPIO59 it uses function number 2.
So, in order to make the driver compatible with upstream DTS to avoid the
need to patch the pinctrl nodes in U-Boot and support all of the missing
pin functions lets rework the driver based on upstream Linux IPQ4019
pinctrl driver and the pending SM8150 U-Boot pinctrl driver which also uses
different function numbers pased on the exact pin number.
Signed-off-by: Robert Marko <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
If compiled with logging and debug UART support, the following is printed:
serial_msm serial@78af000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
This is due to the fact that IPQ4019 pinctrl driver is not available prior
to relocation and thus MSM serial will fail probing as pinctrl provider is
not available.
So, lets enable DM_FLAG_PRE_RELOC for IPQ4019 pinctrl to fix this.
Signed-off-by: Robert Marko <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
We want to use OF_UPSTREAM on IPQ40XX as its well supported upstream, so
as a preparation update pinctrl driver to look for the upstream pin format.
Signed-off-by: Robert Marko <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
IPQ4019 pinctrl driver was moved to the dedicated Qualcomm pinctrl
directory, but the KConfig depends on ARCH_SNAPDRAGON only and thus
PINCTRL_QCOM_IPQ4019 cannot be selected when ARCH_IPQ40XX is used.
Fixes: 24d2908e987a ("pinctrl: qcom: move ipq4019 driver from mach-ipq40xx")
Signed-off-by: Robert Marko <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Adjust sdm845_get_pin_name() to return the correct names for the special
pins. This fixes a non-fatal -ENOSYS error when probing MMC.
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
This SoC features a pinctrl block with north, south, and west tiles
accessible to the AP.
Reviewed-by: Neil Armstrong <[email protected]>
Acked-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
This SoC features a pinctrl block with west, east, and south tiles.
Reviewed-by: Neil Armstrong <[email protected]>
Acked-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
This SoC has a basic pinctrl block with no tiles.
Reviewed-by: Neil Armstrong <[email protected]>
Acked-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add pinctrl driver for the TLMM block found in the SM8650 SoC.
This driver only handles the gpio and qup2_se7 pinmux, and makes sure
the pinconf applies on SDC2 pins.
Signed-off-by: Neil Armstrong <[email protected]>
Acked-by: Sumit Garg <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add pinctrl driver for the TLMM block found in the SM8550 SoC.
This driver only handles the gpio and qup1_se7 pinmux, and makes sure
the pinconf applies on SDC2 pins.
Signed-off-by: Neil Armstrong <[email protected]>
Acked-by: Sumit Garg <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
This patch is the preparation for SM8150 support. This new SoC
depending on the particular pin can have different numbers for the
same function. For example "rgmii" function for GPIO4 has id=2 while
for GPIO59 it has id=1. So, to support this type of SoCs,
get_function_mux() callback needs to know for which pin the function
is requested.
Signed-off-by: Volodymyr Babchuk <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Prepare v2024.04-rc4
|
|
Pinconfig nodes normally bind recursively with PINCTRL_FULL and
PINCONF_RECURSIVE enabled. However, during U-Boot proper pre-relocation
any node marked with e.g. bootph-all will not bind unless its parent is
also marked for pre-reloc.
group1 {
pinconf1 {
bootph-all;
};
};
This cause the following warning message to be shown during U-Boot
proper pre-reloc stage on Rockchip devices, e.g on RK3568:
ns16550_serial serial@fe660000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
and on RK3328:
ns16550_serial serial@ff130000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Check pinconfig nodes pre-reloc status recursively to fix this and to
make pinconfig_post_bind work same at both U-Boot proper pre-reloc and
at TPL/SPL stage.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
|
|
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Paul Barker <[email protected]>
|
|
Rename rmobile_get_cpu_rev_*() to renesas_get_cpu_rev_*() because
all the chips are made by Renesas, while only a subset of them is
from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_cpu_rev_\(integer\|fraction\)\>' | \
xargs -I {} sed -i 's@\<rmobile_get_cpu_rev_\(integer\|fraction\)\>@renesas_get_cpu_rev_\1@g' {}
"
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Paul Barker <[email protected]>
|
|
Add THRU0-3 and SIOPBI/SIOPBO pin groups/functions.
Signed-off-by: Ivan Mikhaylov <[email protected]>
|
|
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Tested-by: Sumit Garg <[email protected]> #qcs404
Signed-off-by: Caleb Connolly <[email protected]>
|
|
On the DB410c we support running as a first stage bootloader. This
requires initialising the GPIOs which are muxed to UART before they can
be used. Add DM_FLAG_PRE_RELOC to the apq8016 pinctrl driver to ensure
that we do this early enough.
This is required to prevent the first few lines of UART log from being
dropped.
Reported-by: Sumit Garg <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Tested-by: Sumit Garg <[email protected]> #qcs404
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Upstream devicetrees label GPIOs with "gpioX", not "GPIO_X", fix this
for SoCs where we're now using upstream DT.
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Tested-by: Sumit Garg <[email protected]> #qcs404
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Most platforms have a handful of "special" GPIOs, like the MMC
clock/data lanes, UFS reset, etc. These don't follow the usual naming
scheme of "gpioX" and also have unique capabilities and registers. We
can get away without supporting them all for now, but DT compatibility
is still an issue.
Add support for allowing these to be specified after the other pins, and
make all pinmux/pinconf calls for them nop.
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Tested-by: Sumit Garg <[email protected]> #qcs404
Signed-off-by: Caleb Connolly <[email protected]>
|
|
|
|
Add pinctrl tables for R8A779H0 V4M SoC.
The current version of these PFC tables is imported and squashed from:
https://lore.kernel.org/linux-renesas-soc/[email protected]/
Signed-off-by: Hai Pham <[email protected]>
|
|
This function is a no-op. Remove it.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Paul Barker <[email protected]>
|
|
Add pinctrl support for Exynos850 SoC. It was mostly extracted from
corresponding Linux kernel code [1]. Power down modes and external
interrupt data were removed while converting the code for U-Boot, but
everything else was kept almost unchanged.
[1] drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Chanho Park <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Drop the duplicated pinctrl-snapdragon driver from mach-ipq40xx and add
it to drivers/pinctrl/qcom.
Acked-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
|
|
Use counterpart dev_read_* functions instead of fdt* ones. It fixes
checkpatch warnings like this:
WARNING: Use the livetree API (dev_read_...)
#54: FILE: drivers/pinctrl/exynos/pinctrl-exynos.c:137:
pinvals[idx] = fdtdec_get_int(fdt, node,
and also makes it possible to avoid using the global data pointer in the
driver.
No functional change.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Pull some variables declared in exynos_pinctrl_set_state() into its
loop, to reduce their scope. Style commit, no functional change.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
All pin related dt properties (pin-function, pin-pud and pin-drv) are
handled in a very similar way. Get rid of that code duplication by
extracting the corresponding data knowledge into an actual data
structure (array), and then just iterating over it.
No functional change, it's a refactoring commit.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Get rid of hard-coded register offsets and widths. Instead provide a way
for pinctrl drivers to specify different pin bank register offsets and
widths. This in turn makes it possible to add support for new SoCs that
have registers with offset/width values different than generic ones
already available in pinctrl-exynos driver.
Offset constants (now unused in pinctrl-exynos.c) are moved to
pinctrl-exynos7420 driver, which is the single user of those constants.
The design of this patch follows Linux kernel pinctrl-exynos driver
design, in terms of added data structures and types. This patch doesn't
add support for any new SoCs and shouldn't introduce any functional
changes.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Rework pin_to_bank_base() function to obtain bank data structure by bank
name instead of getting bank base address by pin name, and rename it to
get_bank() to reflect this change. This in turn leads to the extraction
of parse_pin(), so the caller has to use it before calling get_bank().
No functional change. This is a refactoring commit which prepares
pinctrl driver code for handling different sizes of register fields,
which will be added next.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Next commits are going to re-design the pin_to_bank_base() function and
its usage in a way that the pin parsing code will be called separately.
Extract it into a separate function first, as a refactoring commit.
No functional change.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Style commit, no functional change.
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Move all existing pinmux and funcmux code into a dedicated folder in
pinctrl to simplify further maintenance.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
The existing pinctrl driver available for Tegra SOC is well
designed, but it lacks DM support. Let's add a DM compatible
overlay, which allows use of the device tree, along with preserving
backward compatibility with all existing setups and the ability
to use it in SPL board configuration stage.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Prepare v2024.01-rc3
|
|
Add stm32mp2 compatible.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before
DRAM controller initialization. Therefore, this buffer must be placed in
the .data section.
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
|
|
In line with changes elsewhere, drop inclusion of the common header.
Signed-off-by: Paul Barker <[email protected]>
|
|
GPIO function name is needed in the debug log
Signed-off-by: Jim Liu <[email protected]>
|
|
This adds the remaining code bits to teach U-Boot about Allwinner's
newest SoC generation. This was introduced with the RISC-V based
Allwinner D1 SoC, which actually shares a die with the ARM cores versions
called R528 (BGA, without DRAM) and T113s (QFP, with embedded DRAM).
This adds the new Kconfig stanza, using the two newly introduced symbols
for the new SoC generation and pincontroller. It also adds the new symbols
to the relavent code places, to set all the hardcoded bits directly.
We need one DT override:
The ARM core version of the DT specifies the CPUX watchdog as
"reserved", which means it won't be recognised by U-Boot. Override this
in our generic sunxi-u-boot.dtsi, to let U-Boot pick up this watchdog,
so that the generic reset driver will work.
Signed-off-by: Andre Przywara <[email protected]>
|
|
Apart from using the new pinctrl MMIO register layout, the Allwinner D1
and related SoCs still need to usual set of mux values hardcoded in
U-Boot's pinctrl driver.
Add the values we need so far to this list, so that DM based drivers
will just work without further ado.
Signed-off-by: Andre Przywara <[email protected]>
|
