| Age | Commit message (Collapse) | Author |
|---|
|
Functions for reading indexed values from device tree
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
|
|
Currently, the baud rate is never set on boot. This works ok when a previous
bootloader has configured the baudrate properly, or when the baudrate is set to
a reasonable default in the serial driver's probe(). However, when this is not
the case, we could be using a different baud rate than what was configured.
Signed-off-by: Sean Anderson <[email protected]>
|
|
Some callers may need the UART base clock speed value.
Provide it in the ->getinfo() callback.
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Some callers of serial_getinfo() would like to know the UART base
clock speed in order to make decision what to pass to OS in some
cases. In particular, ACPI SPCR table expects only certain base
clock speed and thus we have to act accordingly.
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
The commit a673025535ae ("serial: zynq: Initialize uart only before
relocation") introduced code which detects relocation which is working for
single uart instance. With multiple instances in place there is a need to
enable and setup every instance. That's why detect if TX is enabled. If it
is then don't initialize uart again.
In post probe setbrg is called to setup baudrate but values should be the
same.
As a side effect of this change is that DECLARE_GLOBAL_DATA_PTR can be
removed completely.
Signed-off-by: Michal Simek <[email protected]>
|
|
Currently the driver gets ns16550 base address in the driver
probe() routine, which may potentially break any ns16550 wrapper
driver that does additional initialization before calling
ns16550_serial_probe().
Things are complicated that we need consider ns16550 devices on
both simple-bus and PCI bus. To fix the issue we move the base
address assignment for simple-bus ns16550 device back to the
ofdata_to_platdata(), and assign base address for PCI ns16550
device in ns16550_serial_probe().
This is still not perfect. If any PCI bus based ns16550 wrapper
driver tries to access plat->base before calling probe(), it is
still subject to break.
Fixes: 720f9e1fdb0c9 ("serial: ns16550: Move PCI access from ofdata_to_platdata() to probe()")
Reported-by: Andy Shevchenko <[email protected]>
Signed-off-by: Bin Meng <[email protected]>
Tested-by: Andy Shevchenko <[email protected]>
Reviewed-by: Wolfgang Wallner <[email protected]>
Tested-by: Wolfgang Wallner <[email protected]>
|
|
All drivers seems to align now to serial_xxx maning, so, aligning
also this driver, to allow to be found easily.
Signed-off-by: Angelo Durgehello <[email protected]>
|
|
Actually, using dev->seq value before probe to deduce the current
serial port index leads to reading an invalid seq value (-1).
So, getting dev->seq at probe time.
Signed-off-by: Angelo Durgehello <[email protected]>
|
|
Some device may enable CONFIG_CLK but not still support this clock in
CC, so better use debug() in place of dev_warn() otherwise a lot of
boards will throw useless dev_warn()s.
Signed-off-by: Giulio Benetti <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Currently the ofdata_to_platdata() method calls dev_read_addr_pci(),
which potentially accesses the parent PCI bus. If this happens before
the parent PCI bus is probed the resulting address will be wrong.
This behavior was triggered by commit 82de42fa1468 ("dm: core:
Allocate parent data separate from probing parent").
According to a comment in drivers/pci/pci-uclass.c [1] accessing
the PCI parent bus in ofdata_to_platdata() is not allowed, and the
access should be moved to the probe() function.
Move the call to dev_read_addr_pci() and the related handling of the
'addr' value from the ofdata_to_platdata() to its own function,
which is then called from the probe() method.
While moving the code, the comment /* try Processor Local Bus device
first */ was dropped. It was initially added with commit 3db886a5bf38
("serial: ns16550: Support ns16550 compatible pci uart devices") and
later made obsolete with commit 33c215af4b9d ("dm: pci: Add a function
to read a PCI BAR").
[1] Comment in drivers/pci/pci-uclass.c:
"A common cause of this problem is that this function is called in the
ofdata_to_platdata() method of @dev. Accessing the PCI bus in that
method is not allowed, since it has not yet been probed. To fix this,
move that access to the probe() method of @dev instead."
Fixes: 82de42fa1468 ("dm: core: Allocate parent data separate from probing parent")
Signed-off-by: Wolfgang Wallner <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Tested-by: Bin Meng <[email protected]> # Tested on Intel Galileo
|
|
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
|
|
Add serial UART driver support for all Cortina Access
CAxxxx family of SoCs.
Reviewed-by: Daniel Schwierzeck <[email protected]>
Signed-off-by: Jason Li <[email protected]>
Signed-off-by: Alex Nemirovsky <[email protected]>
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Anatolij Gustschin <[email protected]>
|
|
Coreboot can provide information about the serial device in use on a
platform. Add a driver that uses this information to produce a working
UART.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
At present this driver uses an assortment of CONFIG options to control
how it accesses the hardware. This is painful for platforms that are
supposed to be controlled by a device tree or a previous-stage bootloader.
Add a new CONFIG option to enable fully dynamic configuration. This
controls register spacing, size, offset and endianness.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Aiden Park <[email protected]>
Tested-by: Aiden Park <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
[bmeng: squashed in http://patchwork.ozlabs.org/patch/1232929/]
Signed-off-by: Bin Meng <[email protected]>
|
|
If baud_divisor is not set (i.e. == -1), we should use the baud divisor
already in use for flushing the xmit register. If we don't flush the
xmit register, then SPL will hang.
Signed-off-by: Patrik Dahlström <[email protected]>
|
|
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <[email protected]>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <[email protected]>
|
|
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <[email protected]>
|
|
This seems pretty old now. It has not been converted to driver model and
is not used by any boards.
Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some features implicitly depended on MALLOC_F and OF_LIBFDT and would
fail at link-time if these features were not enabled.
Signed-off-by: Sean Anderson <[email protected]>
|
|
Add i.MXRT compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also according to RM, the Receive RX FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08 as done
for i.MX8. It needs also to set baudrate the same way as i.MX8 does.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
This driver assumes that lpuart clock is already enabled before probing
but using DM only lpuart won't be automatically enabled so add
clk_enable() when probing if CONFIG_CLK is defined. If clock is not
found, because DM is not used, let's emit a warning and proceed, because
serial clock could also be already enabled by non DM code. If clock is
found but cna't be enabled then return with error.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
Due to a conversion error the sandbox does not accept byte values 0x80-0xff
from the keyboard. The UEFI extended text input unit test requires Unicode
support.
Use unsigned char for the serial buffer.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
|
|
Fix stdout-path handling
|
|
This missing dependency seems like an oversight, since all other
TPL_DM_* options have it.
Signed-off-by: Thomas Hebb <[email protected]>
|
|
The function declarations in serial.h are not in sync with what is
currently used in usbtty. Fix this by updating the header and including
it, to help catch future such problems.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
With commit f0921f5098d8 ("fdt: Sync up to the latest libfdt"),
SiFive Unleashed board does not boot any more. This was due to
the U-Boot local changes commit 77d7fff8cec2 ("fdt: Fix handling
of paths with options in them") to libfdt/fdt_ro.c was dropped
during the libfdt upgrade.
>From the history [1] it was mentioned that the U-Boot changes
commit 77d7fff8cec2 ("fdt: Fix handling of paths with options in
them") was rejected by libfdt upstream, hence we need find another
way to fix the things.
This commit uses another method, by updating serial_check_stdout()
directly to handle the situation of "stdout-path" with ":options".
A simpler way is to change the logic in fdtdec_get_chosen_node()
to do similar thing, but I feel that not every property in chosen
node may have the option in them, hence it would make more sense
to do the special handling in serial_check_stdout() directly.
[1]: http://patchwork.ozlabs.org/patch/462756/
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
U-Boot support on Raspberry Pi 4 relies on the device-tree
provided by the firmware. The blob does not contain the
U-Boot specific pre-loc-rel properties. The result is, that
the U-Boot banner is not printed.
We fix this by setting the DM_FLAG_PRE_RELOC flag in the driver,
if we rely on a device-tree provided by the firmware.
Reported-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Matthias Brugger <[email protected]>
|
|
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.
Signed-off-by: Weijie Gao <[email protected]>
|
|
This patch adds codes to enable FIFO and disable flow control taken from
ns16550 driver.
Signed-off-by: Weijie Gao <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191009
-------------------
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532
- MX6UL / ULZ
- Toradex board
- Allow to set OCRAM for MX6Q/D
- MX7ULP
- MX8: (container image, imx8mq_mek), SCU API
- fix several board booting from SD/EMMC (cubox-i for example)
- pico boards
[trini: display5 merged manually]
Signed-off-by: Tom Rini <[email protected]>
|
|
i.MX7 and i.MX8M use mxc uart driver, so let's make the SoC could
use MXC_UART kconfig.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Ye Li <[email protected]>
|
|
At present PCI address transaction is not supported so drivers must
manually read the correct BAR after reading the device tree info. The
ns16550 has a suitable implementation, so move this code into the core
DM support.
Note that there is no live-tree equivalent at present.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Tested-by: Bin Meng <[email protected]>
[bmeng: correct the unclear comments in test.dts]
Signed-off-by: Bin Meng <[email protected]>
|
|
At present this function is never called when of-platdata is enabled since
we never have a device tree. However, this function is responsible for
copying over the of-platdata, so we must call it. Otherwise the probe()
method would have to be used.
Correct this and fix the sandbox serial driver to not read from the device
tree and try to write to what is read-only platdata on some platforms.
Fixes: 396e343b3d (dm: core: Allow binding a device from a live tree)
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
At present this driver uses the wrong condition for including the code and
drivers in SPL/TPL. Update it so that the code is only included if
DM_SERIAL is enabled for SPL/TPL.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add management of Bit 1 of USART_ISR = FE: Framing error
This bit is set by hardware when a de-synchronization, excessive noise
or a break character is detected. It is cleared by software, writing 1
to the FECF bit in the USART_ICR register (for stm32 after f4).
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, SPL/TPL options
when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit. In some instances, I wasn't sure
of DM was required, so I simply made them SPL or TPL.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <[email protected]>
|
|
In y-modem transfer mode, tstc/getc fail to check if there is any
data available / received in RX FIFO, and so y-modem transfer never
succeeds. Using receive watermark bit within ip register fixes the
issue.
This patch is based on commit c7392b7bc4e1 ("Use the RX watermark
interrupt pending bit for TSTC") available at[1]
[1] https://github.com/sifive/HiFive_U-Boot/tree/regression
Signed-off-by: Sagar Shrikant Kadam <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Tested-by: Anup Patel <[email protected]>
Reviewed-by: Padmarao Begari <[email protected]>
Tested-by: Padmarao Begari <[email protected]>
|
|
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Goldschmidt <[email protected]>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Move env_get() over to the new header file.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Should use CONFIG_IS_ENABLED not IS_ENABLED for CLK driver, so it will
check the CONFIG_SPL_CLK when building SPL
Signed-off-by: Ye Li <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This patch fixes not enabled uart2 (and hence serial console) on i.MX53
devices. After following commit 1d255904c306 ("ARM: dts: imx: imx53:
Synchronize iMX53 DT with Linux") from the uart2 compatible the
'fsl,imx7d-uart' has been removed (which was correct).
However, the root cause of the problem was the commit 98d62e618bb9 ("arm:
imx: add i.MX53 Beckhoff CX9020 Embedded PC") which introduced this
compatible.
Moreover, without this patch all i.MX53 UARTs are not usable as neither
'fsl,imx53-uart' nor 'fsl,imx21-uart' are in compatible IDs in
drivers/serial/serial_mxc.c file.
The fix is to add 'fsl,imx53-uart' and 'fsl,imx21-uart' as compatibles
for the aforementioned serial driver (those are also defined in the Linux
kernel).
Signed-off-by: Lukasz Majewski <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
The DM_FLAG_PRE_RELOC shall be set unconditionally as this driver is going
to be re-used in both early SPL and U-Boot proper's pre-reloc.
For i.MX based devices it is crucial to have available the serial console
before relocation (otherwise the board may hand).
The device definition may be provided either via device tree description or
with U_BOOT_DEVICE(mxc_serial) definition. In the latter case the device
will not bind in U-Boot proper when DM_FLAG_PRE_RELOC is not set.
The !CONFIG_IS_ENABLED(OF_CONTROL) #if check was set as a "workaround" for
DM problem described in following commit 4687919684e0
("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers").
Let's look on this check more thoroughly - we add this flag if the board
doesn't support OF_CONTROL. This is a bit strange as the serial_mxc.c can
be used with CONFIG_DM_SERIAL but without corresponding device tree
description (OF_CONTROL). In such case the aforementioned
U_BOOT_DEVICE(mxc_serial) definition is used.
Other boards/SoCs have this flag set unconditionally for serial driver.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
|
|
This patch solves the following warnings:
drivers/serial/serial_stm32.c: In function 'stm32_serial_probe':
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (plat->clock_rate < 0) {
^
Signed-off-by: Patrice Chotard <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
By default LPUART driver with compatible string "fsl,ls1021a-lpuart"
support big-endian mode.On NXP SoC like LS1028A LPUART IP is
little-endian,Added support to Fetch LPUART IP Endianness from lpuart
device-tree node.
Signed-off-by: Vabhav Sharma <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add compatible string for iMX6SX.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Silvio Fricke <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
- Add various STM32MP1 fixes for serial, env, clk, board, i2c ...
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
|
|
This patch adds devicetree support to the mcfuart.c driver
and removes non DM code.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Angelo Dureghello <[email protected]>
|
