| Age | Commit message (Collapse) | Author |
|---|
|
Add a USB controller driver for the EHCI block in R8A7795/R8A7796 SoC.
This is a stopgap measure until we have proper DT support, clock and
reset framework in place, at which point we can switch to ehci-generic.
Signed-off-by: Hiroyuki Yokoyama <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Hiroyuki Yokoyama <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Reviewed-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Follow the exiting logic for the i.MX options when migrating this
option.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the USB port index.
Cc: Lokesh Vutla <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Roger Quadros <[email protected]>
Signed-off-by: Uri Mashiach <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Nadav Haklai <[email protected]>
Cc: Neta Zur Hershkovits <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Haim Boot <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Move symbol to Kconfig to cleanup configuration file.
Signed-off-by: Michal Simek <[email protected]>
|
|
This patch adds DM based support for the xHCI USB 3.0 controller
integrated in the Armada 3700 SoC. It may be extended to be used
by other MVEBU SoCs as well.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Nadav Haklai <[email protected]>
Cc: Kostya Porotchkin <[email protected]>
Cc: Wilson Ding <[email protected]>
Cc: Victor Gu <[email protected]>
Cc: Hua Jing <[email protected]>
Cc: Terry Zhou <[email protected]>
Cc: Hanna Hawa <[email protected]>
Cc: Haim Boot <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Add a Kconfig for Rockchip xhci controller.
Signed-off-by: Kever Yang <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This driver has not been converted to Driver Model, and it is an
obstacle to migrate other block device drivers. Remove it for now.
The UniPhier SoCs already use a DM-based EHCI driver, so now
ARCH_UNIPHIER can select DM_USB.
These two changes must be done atomically because removing the
legacy driver causes a build error.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.
Signed-off-by: Wenyou Yang <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
The meaning of CONFIG_USB in U-Boot is different from that in Linux.
As you see in drivers/usb/Kconfig of Linux, CONFIG_USB enables the
USB host controller support, while CONFIG_USB_SUPPORT is used to
enable the whole of the USB sub-system.
When I added CONFIG_USB into Kconfig by commit 6e7e9294d321 ("usb:
add basic USB configs in Kconfig"), I planned to follow the Linux's
convention, i.e. CONFIG_USB to enable/disable the USB host support.
Then, commit 68f7c5db2d1e ("usb: Generic USB Kconfig option, that
fits both host and gadget and comments") changed the logic of the
CONFIG_USB to point to the whole of the USB sub-system. As a result,
currently we do not have an option for USB host.
This commit adds CONFIG_USB_HOST, which will be useful to compile
in the USB host support code.
CONFIG_USB_HOST is not referenced at all, but strangely some boards
define it in board headers. I removed them because USB_HOST will be
selected in Kconfig going forward.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
There is no UHCI driver entry in Kconfig for now, but we have some
UHCI drivers, for example, LEON. This is a placeholder in case we
want to move them to Kconfig in the future.
The help message was copied from Linux.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add this option as a common config for all OHCI controllers. Its
help message was copied from Linux. Also, I moved it below EHCI
to respect the order in Linux's Kconfig.
Add CONFIG_USB_OHCI_HCD=y to axs103_defconfig, which is the only
user of OHCI_GENERIC.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
|
|
Add Kconfig entry config option for USB_EHCI_ZYNQ
and update the same to enable for all zynq boards
which supports USB
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Add a new config CONFIG_MXC_USB_OTG_HACTIVE which configures the
OTG Power Pin to be high active. Low active is the reset value
of the affected configuration register, hence the config option
is named by the non-reset configuration.
Signed-off-by: Stefan Agner <[email protected]>
|
|
Create an entry for "config USB_EHCI_MX7" in Kconfig and
switch over to it for all boards.
Signed-off-by: Stefan Agner <[email protected]>
|
|
Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
|
Now, all this driver does can be covered by the generic EHCI driver
(drivers/usb/host/ehci-generic.c). UniPhier SoCs have switched to
use it. Delete this driver rather than bothering to convert it to
Driver Model.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This driver is meant to be used with any OHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
This driver is meant to be used with any EHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
This patch adds driver model (DM) support to the Marvell EHCI driver.
This will be used by the MVEBU SoC's, currently Armada XP and 38x.
Tested on Marvell Armada XP and 38x eval boards.
Signed-off-by: Stefan Roese <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
Add USB_EHCI_MX6 option to menuconfig and use it when migrating cm-fx6 usb
config to defconfig.
Cc: Masahiro Yamada <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
The business for UniPhier Soc family has been transferred from
Panasonic Corporation to Socionext Inc.
Update the SoC select menu in Kconfig.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Support xHCI host driver used on Panasonic UniPhier platform.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Now UniPhier platform highly depends on Device Tree configuration
(CONFIG_OF_CONTROL is select'ed by Kconfig). Since the EHCI is only
used on main U-Boot, we can drop platform devices of the EHCI
controllers. We still keep UART platform devices because they might
be useful for SPL.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
