| Age | Commit message (Collapse) | Author |
|---|
|
The xhci.h header file is currently located under drivers/usb/xhci
Move it to the include/usb folder to make it available to drivers that
are not under drivers/usb/xhci
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
This allow the phy to enter idle and then suspend.
the K2 platforms require the PHY to be suspended before the USB domain
clock can be turned off.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
This driver is not used anymore.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
Phy setup should be done before dwc3 soft core reset as it is done
in linux & this fixes unreliable detection of usb cable on host side.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
- Assorted bugfixes
|
|
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
commit 65c1f9820c8f79f "usb: Add nonblock argument to submit_int_msg"
breaks the musb_hcd driver.
Fixing it by adding the missing argument
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
An USB 1.1 keyboard connected to dwc2 through a high-speed hub does not
report status until it changes. With this patch you can enable keyboard
by pressing a key while USB devices are probed. Without a keypress no
state is reported and the probe times out. We don't want to wait for a
keypress or timeout while polling for keypresses so implement an int_msg
nonblock variant that exits early on error.
Signed-off-by: Michal Suchanek <[email protected]>
|
|
This will be used to implement non-blocking keyboard polling in case of
errors.
Signed-off-by: Michal Suchanek <[email protected]>
|
|
This quirk is necessary for the Amlogic GXL SoCs otherwise the
Port 2 PHY doesn't get out of suspend and U-Boot resets the board after:
XHCI timeout on event type 33... cannot recover.
BUG: failure at drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()!
BUG!
This quirk is also handled in the dwc3 core code, but until the
xhci-dwc3 driver uses the dwc3 core, the quirk must be handled here
to fix USB support on the Amlogic libretech-cc and libretech-ac board
when a device is only plugged in the OTG port.
Cc: Yuri Frolov <[email protected]>
Cc: Bin Meng <[email protected]>
Fixes: dc9cdf859e ("usb: dwc3: Add DWC3 controller driver support")
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add DM regulator support for toggling VBUS, this is useful on boards
which control the VBUS e.g. through GPIO.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
Fix remaining checkpatch complaints in the driver.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
Add missing Kconfig entry for the R8A66597 driver.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
Convert the R8A66597 USB driver to DM and add support for DT probing.
Drop support for legacy non-DM and non-DT probing, since there are no
platform using that.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
Replace R8A66597_BASE0 with proper SYSCFG0 accesses, no functional
change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
While the USB controller can work both in LE and BE modes, there is
no user for the BE mode, so drop it. If there ever is a user for it,
it can be easily re-added back.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
Replace in{bwl}()/out{bwl}() IO accessors with read{bwl}()/write{bwl}(),
to make the driver compile both on SH and ARM.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
No other platforms use this r8a66597 controller but RZ/A1,
make RZ/A1 support the default and drop all the other SoC
support to remove ifdeffery.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
Remove CONFIG_SUPERH_ON_CHIP_R8A66597 macro, which is unused.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chris Brandt <[email protected]>
|
|
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Move env_get() over to the new header file.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Move env_set() over to the new header file.
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
dfu_prepare_function() allocates N+1 descriptor header structures,
the last one being the "DFU Functional Descriptor".
dfu_unbind() handles de-allocation, but fails to free the final
one (eg. "DFU Functional Descriptor"), leading to memory leak.
Fixed by incrementing counter, as in dfu_prepare_function().
Signed-off-by: Ralph Siemsen <[email protected]>
|
|
add new DM based PCI driver ohci-pci for PCI-based
OHCI USB support.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Signed-off-by: Heiko Schocher <[email protected]>
|
|
set OHCI_USE_NPS if DM_PCI is enabled.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
commit 57faca19a82f ("drivers: USB: OHCI: allow compilation for 64-bit targets")
broke ohci support for the mpc85xx based socrates board,
as it removed volatile keyword from ohci_readl/writel.
Fix this so usb works again on socrates board.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
var ohci_pci_ids is only used if DM_USB is not enabled.
So define this varaible only if
!CONFIG_IS_ENABLED(DM_USB)
Signed-off-by: Heiko Schocher <[email protected]>
|
|
With the recently added phy driver, this patch will enable the
musb driver on the da8xx to operate in host mode.
Signed-off-by: Adam Ford <[email protected]>
|
|
Remove RK3399 compatible strings as this driver is no longer
used on that SoC.
Signed-off-by: Mark Kettenis <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Configure USB2 PHY register based on "phy_type" property and
handle all the quirks that are relevant for Rockchip RK3399 SoCs.
Signed-off-by: Mark Kettenis <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Add compatible string for RK3399 and enable it by default on
Rockchip platforms with USB3 support.
Signed-off-by: Mark Kettenis <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:
[...]
CC drivers/usb/gadget/f_mass_storage.o
CC drivers/usb/musb-new/omap2430.o
CC drivers/usb/gadget/f_fastboot.o
CC env/common.o
CC env/env.o
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
ret = musb_register(&platdata->plat,
^
LD drivers/usb/host/built-in.o
CC drivers/usb/gadget/f_sdp.o
CC fs/ext4/ext4fs.o
[...]
Signed-off-by: Derald D. Woods <[email protected]>
|
|
dwc3-generic has been broken since MISC uclass has been modified to scan DT
sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
There is simply no reason to do that here.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.
However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.
The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Abel Vesa <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Ludwig Zenz <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Vagrant Cascadian <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2019.07
- menlo board
- allow SDB on Sabre
- HAB for mx6sl
- apalis board
|
|
Add support for loading u-boot FIT images over the USB SDP protocol in
the SPL
Signed-off-by: Frieder Schrempf <[email protected]>
[Various build fixes]
Signed-off-by: Sjoerd Simons <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
|
|
Allow device mode in DWC2 driver when device tree select the dr_mode
"peripheral" or "otg".
The device mode is not allowed when dr_mode = "host" in device tree.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Manage g-tx-fifo-size as a array as specify in the binding.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
So adopt 32 bit address for CONFIG_PPC.
Signed-off-by: Yinbo Zhu <[email protected]>
Reviewed-by: Prabhakar Kushwaha <[email protected]>
|
|
Per feedback from Marek, he suggested better handling and
to enable DM_FLAG_OS_PREPARE, this patch re-orders some of
the error checking, and errors returns the error code right
away and also sets DM_FLAG_OS_PREPARE.
Signed-off-by: Adam Ford <[email protected]>
|
|
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This patch reuses some former code for the hawkboard, combines it
with some some similar DM_USB compatible code for the OHCI driver,
and enables the use of the da850's OHCI controller with DM_USB
compatibility.
Signed-off-by: Adam Ford <[email protected]>
|
|
The support for DaVinci DM* SoCs has been dropped. The ifdefs in the
musb_hcd driver are no longer needed. Remove them.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
- DaVinci updates
|
|
There is a delay function that was commented out. This patch
re-enables it, because it will be needed for da850 ohci support.
Signed-off-by: Adam Ford <[email protected]>
|
|
Improvements and new features:
- improved SPI driver for better read throughput
- refactors initialisation of debug UART init
- restructures header file paths
- adds pinctrl improvements
Adds Kever as a co-custodian.
|
