| Age | Commit message (Collapse) | Author |
|---|
|
When building a FIT, more than one device tree can be included. The board
can select (at run-time) the one that it wants.
Add a Kconfig option to allow the list of devices trees (supported by the
board) to be specified.
When using SPL_LOAD_FIT, build u-boot.img in FIT format instead of the
legacy image format. Include all the listed device tree files in this FIT.
Signed-off-by: Simon Glass <[email protected]>
|
|
This option has no meaning without OF_CONTROL, so add a dependency.
Signed-off-by: Simon Glass <[email protected]>
|
|
These two properties are necessary for SPL to get clocks from DT.
Note:
For now, only clock look-up by index is supported (clk_get_by_index()
function), so "clock-names" is never parsed in U-Boot. However, we
may want to support something like clk_get_by_name() in the future,
so let's keep "clock-names" as well as "clocks".
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This comment from README.fdt-control did not end up in the Kconfig, which
is what most people will see. Add it with a few tweaks.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Michal Simek <[email protected]>
|
|
These properties are necessary to use full-featured pinctrl drivers
in SPL.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This should depend on SPL_OF_CONTROL (it is not equivalent to
SPL && OF_CONTROL).
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The SPL device tree size must be minimised to save memory. Only include
properties that are needed by SPL - this is determined by the presence
of the "u-boot,dm-pre-reloc" property. Also remove a predefined list of
unused properties from the nodes that remain.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some boards cannot support device tree due to lack of memory. Add an option
to allow these boards to continue to work (and even use driver model).
This is a 'negative' option since most boards are expected to support device
tree in SPL.
Signed-off-by: Simon Glass <[email protected]>
|
|
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Signed-off-by: Robert P. J. Day <[email protected]>
|
|
This option specifies the default Device Tree used for the run-time
configuration of U-Boot.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Michal Simek <[email protected]>
|
|
This commit moves:
CONFIG_OF_CONTROL
CONFIG_OF_SEPARATE
CONFIG_OF_EMBED
CONFIG_OF_HOSTFILE
Because these options are currently not supported for SPL,
the "Device Tree Control" menu does not appear in the SPL
configuration.
Note:
zynq-common.h should be adjusted so as not to change the
default value of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Simon Glass <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Minkyu Kang <[email protected]>
Acked-by: Michal Simek <[email protected]>
|
