| Age | Commit message (Collapse) | Author |
|---|
|
MACH_TYPE_TNY_A9G20 and MACH_TYPE_TNY_A9260 were removed
from mach-types.h. Add them to the board config file.
Signed-off-by: Anatolij Gustschin <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
MACH_TYPE_SBC35_A9G20 was removed from mach-types.h.
Add it to the board config file.
Signed-off-by: Anatolij Gustschin <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Fix trailing white space, indentation by spaces instead of TABs,
excessive blank lines, trailing blank lines.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
This commit enables support for USB Gadgets on the Exynos4210 (C210 Universal)
reference target.
Signed-off-by: Lukasz Majewski <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Cc: Minkyu Kang <[email protected]>
CC: Remy Bohmer <[email protected]>
|
|
The early messages can be seen on the debug console.
Signed-off-by: Asen Chavdarov Dimov <[email protected]>
|
|
The early messages can be seen on the debug console.
Signed-off-by: Asen Chavdarov Dimov <[email protected]>
|
|
The early messages can be seen on the debug console.
Signed-off-by: Asen Chavdarov Dimov <[email protected]>
|
|
Switch to extension board detection using pci_find_device()
instead of detecting by i2c access to EEPROM device on
extension board.
This is a cleaner detection method since EEPROM addresses
can be different on different board revisions. This also
avoids "i2c_read: failed to address chip" error messages
in the boot log on boards without extension board which
may confuse users.
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Remy Bohmer <[email protected]>
Cc: Wolfgang Grandegger <[email protected]>
Cc: Jason Liu <[email protected]>
|
|
Signed-off-by: Wolfgang Grandegger <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Remy Bohmer <[email protected]>
Cc: Wolfgang Grandegger <[email protected]>
Cc: Jason Liu <[email protected]>
|
|
Signed-off-by: Wolfgang Grandegger <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Remy Bohmer <[email protected]>
Cc: Wolfgang Grandegger <[email protected]>
Cc: Jason Liu <[email protected]>
|
|
This commit enables support for USB Gadgets on the GONI
reference target.
Signed-off-by: Lukasz Majewski <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Remy Bohmer <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Kyungmin Park <[email protected]>
Cc: Albert Aribaud <[email protected]>
|
|
* 'master' of git://git.denx.de/u-boot-arm:
M28: Cleanup memsize.o OOT build
i.MX28: Move SPL to arch/arm/cpu/arm926ejs/mx28
M28: Fix typo
M28: Document that units has to be set to sectors on SD bootcard
i.mx: i.mx6q: add the initial support for i.mx6q ARM2 board
i.mx: mxc_gpio: add the i.mx6q support
i.mx: add the initial support for freescale i.MX6Q processor
i.mx: introduce the armv7/imx-common folder
S5PC2XX: Rename S5pc2XX to exynos
tegra2: Don't use board pointer before it is set up
tegra2: Remove unneeded 'dynamic ram size' message
tegra2: Remove unused low-level Tegra2 UART code
tegra2: Remove unneeded config option
tegra2: Remove unneeded boot code
tegra2: Enable instruction cache
arm: Move CP15 init out of cpu_init_crit()
tegra2: Simplify tegra_start() boot path
tegra2: Add arch_cpu_init() to fire up Cortex-A9
tegra2: Use new GPIO APIs in gpio_config_uart()
tegra2: Add support for Ventana
tegra2: Modify MMC driver to handle power and cd GPIOs
tegra2: Move board_mmc_init into board files
|
|
* '[email protected]' of git://git.denx.de/u-boot-staging:
Update pci_ids.h from current Linux sources
omap: overo: Use ubifs instead of jffs2 for nand
omap: TWL4030 Bump VMMC1 interface voltage from 3V to 3.15V
|
|
The current way memsize.c is built just made a symlink into the directory
with SPL and then compiled it like any other file there. This was bad as that
broke the out-of-tree build.
The new way introduced in this patch uses the standard spl/Makefile methods
(CONFIG_SPL_LIBCOMMON_SUPPORT / CONFIG_SPL_LIBGENERIC_SUPPORT) to let files in
common/ be built. Because common/Makefile says memsize.c is always built (SPL
and non-SPL build), this fixes our issue with memsize.c out-of-tree build.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Detlev Zundel <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
This moves SPL to common location so it can be reused by multiple boards. Also,
this commit adjusts M28 SoM to avoid breakage due to the move.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Detlev Zundel <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add the initial support for Freescale i.MX6Q Armadillo2 board
Support: MMC boot from slot 0/1, debug UART(UART4), usdhc.
There is two MMC slots on the boards:
mmc dev 0 -> connect USDHC3 -> the lower slot on the board,
mmc dev 1 -> connect USDHC4 -> the upper slot on the board,
Signed-off-by: Jason Liu <[email protected]>
Cc: Stefano Babic <[email protected]>
Tested-by: Dirk Behme <[email protected]>
|
|
As per new naming convention for Samsung SoC's, all Cortex-A9 and Cortex-A15
based SoC's will be classified under the name Exynos. Cortex-A9 and Cortex-A15
based SoC's will be sub-classified as Exynos4 and Exynos5 respectively.
In order to better adapt and reuse code across various upcoming Samsung Exynos
based boards, all uses of s5pc210 prefix/suffix/directory-names are renamed in
this patch. s5pc210 is renamed as exynos4210 and S5PC210/s5pc210 suffix/prefix
are renamed as exynos4/EXYNOS4.
Signed-off-by: Chander Kashyap <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
CONFIG_ENABLE_CORTEXA9 and CONFIG_SKIP_RELOCATE_UBOOT are not needed,
so remove them.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
We want to move away from a special Tegra2 start-up, and just use
arch_cpu_init() instead. However, if we run board_init_f() from boot
we need to build it for ARMv4T, since the Tegra's AVP start-up CPU
does not support ARMv7.
The effect of this is to do the AVP init earlier, and in
arch_cpu_init(), rather that board_early_init_f().
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.
v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
he asked me to add myself for this board.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Signed-off-by: Steve Sakoman <[email protected]>
Tested-by: Ash Charles <[email protected]>
|
|
The eXMeritus HWW-1U-1A unit is a DO-160-certified 13lb 1U chassis
with 3 independent TEMPEST zones. Two independent P2020 computers may
be found inside each zone. Complete hardware support is included.
High-level hardware overview:
* DO-160 certified for passenger aircraft (noncritical)
* TEMPEST ceritified for RED/BLACK separation
* 3 zones per chassis, 2 computers per zone (total of 6)
* Dual-core 1.066GHz P2020 per computer
* One 2GB DDR2 SO-RDIMM module per computer (upgradable to 4GB)
* Removable 80GB or 160GB Intel X18-M SSD per computer
* Front-accessible dual-port E1000E per computer
* Front-accessible serial console per computer
* Front-accessible USB port per computer
* Internal Gigabit crossover within each TEMPEST zone
* Internal unidirectional fiber links across TEMPEST zones
* Battery-backed DS1339 I2C RTC on each CPU.
Combined, each 13lb 1U chassis contains 12GB RAM, 12 cores @ 1.066GHz,
12 front-accessible Gigabit Ethernet ports and 960GB of solid-state
storage with a total power consumption of ~200W.
Additional notes:
* SPD detection is only known to work with the DO-160-certified DIMMs
* CPU reset is a little quirky due to hardware misfeature. Proper
support for the hardware reset mechanism has been left for a later
patch series to address.
Signed-off-by: Kyle Moffett <[email protected]>
Cc: Andy Fleming <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
The "rmu" board has long been unmaintained, and is broken.
Remove it.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
The OXC board has long been unmaintained, and is broken.
Remove it.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
The BAB7xx boards are almost deceased. They cause build warnings, an
it's not worth the effort to fix these. Remove the dead body.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Frank Gottschling <[email protected]>
|
|
This moves CONFIG_SYS_TEXT_BASE one MB after beginning of SD-RAM. Move
CONFIG_SYS_SPL_MALLOC_START to have one MB of free space for the u-boot
image.
CONFIG_SYS_TEXT_BASE was in the middle of the bss-section. This was the
reason for the problems with MMC boot described here:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/118711
Signed-off-by: Simon Schwarz <[email protected]>
Tested-by: Thomas Weber <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
there are two boards based on da850 SOC - OMAP-L138 and AM18x.
In order to differentiate between these two boards, revision id
is passed to kernel via second byte of ATAG_REVISION.
Signed-off-by: Manjunathappa, Prakash <[email protected]>
Signed-off-by: Manjunath Hadli <[email protected]>
|
|
Revision B of the board uses CSD0 for the DRAM,
as usual for MX3 boards. The patch fixes also
some values in the U-Boot environment.
Signed-off-by: Stefano Babic <[email protected]>
|
|
The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.
Signed-off-by: Stefano Babic <[email protected]>
CC: Marek Vasut <[email protected]>
CC: Wolfgang Denk <[email protected]>
CC: Fabio Estevam <[email protected]>
CC: Helmut Raiger <[email protected]>
CC: John Rigby <[email protected]>
CC: Matthias Weisser <[email protected]>
CC: Jason Liu <[email protected]>
Acked-by: Jason Liu <[email protected]>
|
|
Add an SPL_BOARD_INIT hook and for OMAP3 have it turn on i2c. OMAP4
doesn't need i2c enabled in SPL. Enable SPL_BOARD_INIT on devkit8000.
Cc: Frederik Kriewitz <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE
Cc: Nagendra T S <[email protected]>
Tested-by: Koen Kooi <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE
Cc: Vaibhav Hiremath <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add Hynix 200MHz timing information to <asm/arch-omap3/mem.h>.
This also changes CONFIG_SYS_TEXT_BASE to 0x80100000.
Signed-off-by: Tom Rini <[email protected]>
|
|
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
logic is also based on what x-loader does in these cases. Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
0x80100000.
Cc: Dirk Behme <[email protected]>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <[email protected]>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <[email protected]>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This changes to making the board be responsible for providing the
memory initialization timings in SPL and converts the devkit8000
to this framework. In SPL we try and initialize both CS0 and CS1.
Cc: Frederik Kriewitz <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
- booting from NOR Flash with direct boot method
- POST support
- LOGBUF support
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Paulraj Sandeep <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Cc: Igor Grinberg <[email protected]>
Cc: Christian Riesch <[email protected]>
|
|
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the hawkboard use these definitions instead of
defining its own.
Signed-off-by: Christian Riesch <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Syed Mohammed Khasim <[email protected]>
Cc: Sughosh Ganu <[email protected]>
Cc: Mike Frysinger <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
|
|
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the da850evm use these definitions instead of
defining its own.
Signed-off-by: Christian Riesch <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Sudhakar Rajashekhara <[email protected]>
Cc: Mike Frysinger <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
|
|
The previous commit changed it to "zero two" instead of the proper "Oh two". This was completely broken!
Signed-off-by: Koen Kooi <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
Fix:
arch/arm/cpu/arm926ejs/davinci/libdavinci.o: In function `timer_init':
/work/agust/git/u-boot/arch/arm/cpu/arm926ejs/davinci/timer.c:62:
undefined reference to `davinci_arm_clk_get'
drivers/i2c/libi2c.o: In function `i2c_init':
/work/agust/git/u-boot/drivers/i2c/davinci_i2c.c:102:
undefined reference to `davinci_arm_clk_get'
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Sandeep Paulraj <[email protected]>
|
|
This patch removes the definition of stack sizes for
irq and fiq if the CONFIG_USE_IRQ is undefined before.
Acked-by: Enric Balletbo i Serra <[email protected]>
Acked-by: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Thomas Weber <[email protected]>
Acked-by: Luca Ceresoli <[email protected]>
|
|
This patch removes the unused definition of SDRC_R_C_B
from the config files.
Acked-by: Enric Balletbo i Serra <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Thomas Weber <[email protected]>
Acked-by: Luca Ceresoli <[email protected]>
Acked-by: Tom Rini <[email protected]>
|
|
This patch removes the CONFIG_OMAP3430, because it is unused.
Acked-by: Enric Balletbo i Serra <[email protected]>
Acked-by: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Thomas Weber <[email protected]>
Acked-by: Luca Ceresoli <[email protected]>
|
|
Change the CONFIG_SYS_TEXT_BASE and the addresses of SDRAM
buffers used by SPL(heap and BSS) keeping in mind the
following requirements:
1. Make sure that SPL's heap and BSS doesn't come in the way
of Linux kernel, which is typically loaded at 0x80008000. This
will be important when SPL directly loads kernel.
2. Align the CONFIG_SYS_TEXT_BASE between TI internal
U-Boot and mainline U-Boot. This avoids a lot of confusion
and allows for the inter-operability of x-loader, SPL,
internal U-Boot, mainline U-Boot etc. The internal U-Boot's
address can not be changed to that of mainline U-Boot
as internal U-Boot doesn't have relocation and 0x80100000
used by mainline U-Boot will clash with kernel
3. Assume only a minimum amount of memory that may be available
on any practical OMAP4/5 board in future too. We are assuming
a minimum of 128 MB of memory
Signed-off-by: Aneesh V <[email protected]>
|
|
Acked-by: Tom Rini <[email protected]>
Signed-off-by: Aneesh V <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Set console=ttyO2 instead of ttyS2 in default bootargs
according to latest kernel config
Signed-off-by: Aneesh V <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
|
