summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2020-06-27rk3399: Add BOOTENV_SF commandJagan Teki
Add missing BOOTENV_SF command in rk3399 config. Fix it. Fixes: f263b860acf8 ("rk3399: Enable SF distro bootcmd") Signed-off-by: Jagan Teki <[email protected]> Reported-by: Suniel Mahesh <[email protected]> Tested-by: Suniel Mahesh <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-06-22arm: wandboard: move CONFIG_MXC_UART to defconfigHeinrich Schuchardt
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in the .config file. To avoid duplicate definitions move the setting from include/configs/wandboard.h to configs/wandboard_defconfig. Document the debug UART settings in the README. Signed-off-by: Heinrich Schuchardt <[email protected]> Reviewed-by: Fabio Estevam <[email protected]>
2020-06-22colibri_imx6: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22colibri_imx7: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22apalis_imx6: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22apalis-tk1: enable distrobootIgor Opaniuk
1. Use distro_bootcmd as default boot command instead of legacy emmcboot wrapper. 2. Drop emmcboot and sdboot wrappers. 3. Provide proper boot order for Distro Boot. Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22configs/colibri_vf.h: drop sdboot in favour of distro_bootcmdMax Krummenacher
The distro bootscript uses kernel_image to get the file name of the kernel, so change that variable name. UBI boot has precedence in the default boot command. If one wants to boot from SD with a working NAND installation stop in U-Boot and enter: setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd Signed-off-by: Max Krummenacher <[email protected]>
2020-06-22colibri-imx6ull/imx7: define bootubipart for distro bootStefan Agner
When using distro boot to boot from UBI volumes the boot partition has been hardcoded to "UBI" (capital letters). However, our default MTD layout uses "ubi" (lower case letter). Define "ubi" as the default UBI partition for distro boot for Toradex. This allows to use distro boot without having to redefine the MTD partition layout which is useful for TorizonCore. Signed-off-by: Stefan Agner <[email protected]>
2020-06-22colibri_imx7: add addresses required for distro bootStefan Agner
Define addresses required for full distro boot support. Signed-off-by: Stefan Agner <[email protected]>
2020-06-22colibri-imx8x: declare consoleargsOleksandr Suvorov
Store all console-related kernel parameters in dedicated variable. Signed-off-by: Oleksandr Suvorov <[email protected]>
2020-06-22mx6cuboxi: Convert to DM_ETHFabio Estevam
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet Driver Model. This also brings the benefit of restoring Ethernet functionality. Reported-by: Tom Rini <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Tested-by: Tom Rini <[email protected]>
2020-06-20Merge https://gitlab.denx.de/u-boot/custodians/u-boot-shTom Rini
2020-06-18ARM: rmobile: Increase PHY auto-negotiation timeout to 20sMarek Vasut
The ethernet PHY on all known Gen3 boards takes a while to come out of reset, increase the auto-negotiation timeout to prevent it from timing out in case the ethernet is used right after the board was reset. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2020-06-18colibri_imx6: fix video stdout in default environmentAnatolij Gustschin
After migration to DM 'vga' name is not longer supported, change it to 'vidconsole' in the default environment. Signed-off-by: Anatolij Gustschin <[email protected]> Acked-by: Igor Opaniuk <[email protected]>
2020-06-18apalis_imx6: fix video stdout in default environmentAnatolij Gustschin
After migration to DM 'vga' name is not longer supported, change it to 'vidconsole' in the default environment. Signed-off-by: Anatolij Gustschin <[email protected]> Acked-by: Igor Opaniuk <[email protected]>
2020-06-18cm_fx6: fix video stdout in default environmentAnatolij Gustschin
After migration to DM 'vga' name is not longer supported, change it to 'vidconsole' in the default environment. Signed-off-by: Anatolij Gustschin <[email protected]> Cc: Nikita Kiryanov <[email protected]>
2020-06-11arm: Remove pcm051 boardJagan Teki
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Acked-by: Lars Poeschel <[email protected]> Signed-off-by: Jagan Teki <[email protected]>
2020-06-11arm: Remove omap3_pandora_defconfig boardJagan Teki
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Acked-by: Grazvydas Ignotas <[email protected]> Signed-off-by: Jagan Teki <[email protected]>
2020-06-11spi: davinci: Drop non-dm codeJagan Teki
Now all boards which are using davinci SPI driver have moved to SPL_DM so drop the unneeded non-dm code. Cc: Adam Ford <[email protected]> Signed-off-by: Jagan Teki <[email protected]> Tested-by: Adam Ford <[email protected]> #da850-evm
2020-06-11ks2_evm: Switch to DM_SPL, SPL_OF_CONTROLJagan Teki
This would make SPL build to DM_SPL, SPL_OF_CONTROL. Build fine with but not tested. Cc: Vitaly Andrianov <[email protected]> Signed-off-by: Jagan Teki <[email protected]>
2020-06-09Merge tag 'u-boot-imx-20200609' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.07 ----------------- - mx53: mx53menlo Convert to DM_ETH, fix fail boot - imx8mp_evk: fix boot issue - MX6, display5: fix environment - drop warnings (watchdog) for i.MX8mm i.mx8mp - enable bootaux for i.MX8M Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/695929999
2020-06-08imx: imx8mp_evk: fix boot issuePeng Fan
The u-boot-spl.bin pad with ddr firmware conflicts with the CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten by malloc in SPL stage and cause ddr initialization not able to finish. So update the related addresses to fix the issue. Reported-by: Fabio Estevam <[email protected]> Signed-off-by: Peng Fan <[email protected]> Signed-off-by: Fabio Estevam <[email protected]>
2020-06-08imx: Update MTD partitions layout for display5 (i.MX6Q) boardLukasz Majewski
This change updates the MTD partition layout on SPI-NOR memory for display5 board. Signed-off-by: Lukasz Majewski <[email protected]>
2020-06-07rockchip: rockpro64: Store default env into SPIMarcin Juszkiewicz
Board has flash chip on board so let store U-Boot environment there. Signed-off-by: Marcin Juszkiewicz <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-06-07roc-rk3399-pc: Mark default env from SPIJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Updated env offset, size in contrast with default since the U-Boot proper has to start from 384K. Signed-off-by: Jagan Teki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-06-04Convert CONFIG_BOARD_LATE_INIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOARD_LATE_INIT Signed-off-by: Tom Rini <[email protected]>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <[email protected]>
2020-06-04Convert CONFIG_BZIP2 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <[email protected]>
2020-06-04topic_miami: Disable GPIOTom Rini
Per the boards config header file, there is no useful GPIO on these boards. Remove CONFIG_CMD_GPIO from the defconfigs. Cc: Mike Looijmans <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04ARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPITom Rini
The config header for this platform disables both CMD_SF and CMD_SPI and the defconfig leaves them enabled. Disable them from the defconfig and enable them in the header. Cc: Marek Vasut <[email protected]> Cc: Masakazu Mochizuki <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04bcmstb: Migrate CONFIG_CMD_EXT[24]Tom Rini
The common config header for bcm7260 and bcm7445 enable CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the commands being disabled. Enable them via the defconfig. Cc: Thomas Fitzsimmons <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04mx6memcal: Finish migration to defconfig optionsTom Rini
The config header for this platform uses '#undef' in a number of cases. All of the MMC related ones were already handled correctly in the defconfig file. In the case of CONFIG_CMD_FUSE, the command was being built and enabled via defconfig. Disable it in the defconfig, cleanup the header. Reviewed-by: Eric Nelson <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04pfla02: Rework excluding NAND from SPLTom Rini
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD options to defconfig and rework the guards to not try and call the function in SPL builds. Cc: Stefano Babic <[email protected]> Signed-off-by: Tom Rini <[email protected]> Acked-by: Stefano Babic <[email protected]>
2020-06-04serial: Convert ARM_DCC to KconfigTom Rini
The symbol "CONFIG_ARM_DCC" is used to control building drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this. Cc: Luca Ceresoli <[email protected]> Cc: Michal Simek <[email protected]> Cc: Tom McLeod <[email protected]> Cc: Mike Looijmans <[email protected]> Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Luca Ceresoli <[email protected]>
2020-06-04sifive: fu540: Add sample SD gpt partition layoutJagan Teki
This is a sample GPT partition layout for SD card, right now three important partitions are added to make the system bootable. partition layout: Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000022 0x00000821 "loader1" attrs: 0x0000000000000000 type: 5b193300-fc78-40cd-8002-e86c45580b47 guid: cbcbef44-e627-42bc-b134-93b6f3784b8c 2 0x00000822 0x00002821 "loader2" attrs: 0x0000000000000000 type: 2e54b353-1271-4842-806f-e436d6af6985 guid: f54eba28-d8de-4852-978d-1a673777e2ae 3 0x00002822 0x00020821 "rootfs" attrs: 0x0000000000000004 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93 Note: - loader1 would be fsbl or spl - loader2 would be U-Boot or U-Boot proper Signed-off-by: Jagan Teki <[email protected]> Reviewed-by: Bin Meng <[email protected]> Reviewed-by: Pragnesh Patel <[email protected]>
2020-06-04riscv: sifive: fu540: add SPL configurationPragnesh Patel
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin) from MMC boot devices. SPL related code is leveraged from FSBL (https://github.com/sifive/freedom-u540-c000-bootloader.git) Signed-off-by: Pragnesh Patel <[email protected]> Reviewed-by: Bin Meng <[email protected]> Tested-by: Bin Meng <[email protected]> Reviewed-by: Jagan Teki <[email protected]> Tested-by: Jagan Teki <[email protected]>
2020-05-31rockchip: Add initial support for the Pinebook Pro laptop from Pine64.Peter Robinson
Specification: - Rockchip RK3399 - 4GB Dual-Channel LPDDR4 - eMMC socket - mSD card slot - 128Mbit (16Mb) SPI Flash - AP6256 for 11AC WiFi + BT5 - 14 inch 1920*1080 eDP MiPi display - Camera - USB 3.0, 2.0 ports - Type-C port with alt-mode display (DP 1.2) and 15W charge - DC 5V/3A - optional PCIe slot for NVMe SSD drive Signed-off-by: Peter Robinson <[email protected]> Tested-by: Vagrant Cascadian <[email protected]> Reviewed-by: Kever Yang <[email protected]> Signed-off-by: Kever Yang <[email protected]>
2020-05-29rockchip: enable USB OHCI host for RockPro64Marcin Juszkiewicz
U-Boot has video output enabled so time to get keyboard working. => usb reset;usb tree resetting USB... Bus usb@fe380000: USB EHCI 1.00 Bus usb@fe3a0000: USB OHCI 1.0 Bus usb@fe3c0000: USB EHCI 1.00 Bus usb@fe3e0000: USB OHCI 1.0 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found scanning bus usb@fe3e0000 for devices... 3 USB Device(s) found scanning bus dwc3 for devices... cannot reset port 1!? 2 USB Device(s) found scanning usb for storage devices... 2 Storage Device(s) found USB device tree: 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (12 Mb/s, 0mA) U-Boot Root Hub 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (12 Mb/s, 0mA) | U-Boot Root Hub | +-2 Hub (12 Mb/s, 100mA) | ALCOR Generic USB Hub | +-3 Mass Storage (12 Mb/s, 200mA) Kingston DT 101 G2 001478544887BB3157380157 1 Hub (5 Gb/s, 0mA) | U-Boot XHCI Host Controller | +-2 Mass Storage (5 Gb/s, 76mA) ADATA ADATA USB Flash Drive 1520405012240002 Signed-off-by: Marcin Juszkiewicz <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-05-29rk3399: Enable NVMe distro bootcmdMark Kettenis
Include NVME in the list of boot targets if CONFIG_NVME is enabled. Signed-off-by: Mark Kettenis <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-05-27arm: mvebu: Convert CRS305-1G-4S board to CRS3xx-98DX3236Luka Kovacic
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier implementation of new CRS3xx series boards, based on Marvell Prestera 98DX3236. Signed-off-by: Luka Kovacic <[email protected]> Reviewed-by: Stefan Roese <[email protected]> Cc: Luka Perkov <[email protected]> Cc: Jakov Petrina <[email protected]>
2020-05-27arm: mvebu: ds414: define CONFIG_SYS_U_BOOT_OFFSEzra Buehler
Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot will be located at address 0x16000. But, SPL will try to load the payload from 0x24000 causing the boot to hang. Signed-off-by: Ezra Buehler <[email protected]> Reviewed-by: Stefan Roese <[email protected]>
2020-05-25sandbox: move compression option to KconfigMichael Walle
CONFIG_BZIP2 and CONFIG_GZIP_COMPRESSED are Kconfig options. Select them by CONFIG_SANDBOX instead of setting them in configs/sandbox.h. Signed-off-by: Michael Walle <[email protected]> Reviewed-by: Simon Glass <[email protected]>
2020-05-25Convert CONFIG_CMD_MMC to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_MMC Signed-off-by: Tom Rini <[email protected]>
2020-05-22Merge branch 'net' of git://git.denx.de/u-boot-socfpgaTom Rini
- ks8851 cleanups and DM migration
2020-05-22net: ks8851: Add Kconfig entriesMarek Vasut
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig Signed-off-by: Marek Vasut <[email protected]> Cc: Eugen Hristev <[email protected]> Cc: Joe Hershberger <[email protected]>
2020-05-22rockpro64: Enable HDMI output on rockpro64 boardAndrius Štikonas
Reference to commit that adds HDMI to other rk3399 boards: commit 9778edae5576 ("rockchip: Enable HDMI output on rk3399 board w/ HDMI") Signed-off-by: Andrius Štikonas <[email protected]> Cc: Manivannan Sadhasivam <[email protected]> Cc: Jagan Teki <[email protected]> Cc: Kever Yang <[email protected]> Tested-by: Mark Kettenis <[email protected]> Reviewed-by: Jagan Teki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-05-20Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds - QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based platforms - Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
2020-05-19mpc83xx, abb: remove suvd3 boardHeiko Schocher
the mpc83xxx suvd3 variant is not longer used, so remove it. Signed-off-by: Holger Brunck <[email protected]> Signed-off-by: Heiko Schocher <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
2020-05-19include/configs: ls1046afrwy: add support for boot targets.Pramod Kumar
ls1046afrwy does not support sata boot. So Override default BOOT_TARGET_DEVICES and support only mmc, usb and dhcp as boot targets. Signed-off-by: Pramod Kumar <[email protected]> [Rebased] Signed-off-by: Priyanka Jain <[email protected]>
2020-05-19configs: ls1012a: Increase CONFIG_SYS_MALLOC_LEN sizeKuldeep Singh
CONFIG_SYS_MALLOC_LEN is currently set to low value and leaves very less space to do malloc in flash environmet. Increase the value to get more memory and also make it align with other boards(ls1046a, ls1043a etc.) config values. Signed-off-by: Kuldeep Singh <[email protected]> Reviewed-by: Priyanka Jain <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-09-04 02:22:05 +0000