| Age | Commit message (Collapse) | Author |
|---|
|
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
|
|
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <[email protected]>
Signed-off-by: Jason Zhu <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
- enable RPi Zero 2 W
- fix MMC numbering issue
- Update link to documentation
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
- enable KSZ90x1 PHY driver on DHCOR
- DHSOM boards:
- increase USB power-good delay
- add update_sf script to install U-Boot into SF
- increase PHY auto-negotiation timeout to 20 seconds
- fix SoM and board coding strap GPIO handling
# gpg verification failed.
|
|
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This changed the default boot device and caused boot failure.
Update the mmcdev variable to reflect the new aliases.
Signed-off-by: Adam Ford <[email protected]>
|
|
Add boot command "bootcmd_ram" to support autoboot from RAM.
This feature could be useful at the very initial state of chip design
when there is only a minimal set of peripheral. (e.g. without mmc and mac ..etc)
The kernel image is default to be loaded at 0x2000000 via debug port,
and the following script serves as an example:
spl()
{
cmd="riscv64-linux-gdb -q \
-ex \"target remote $host:$port\" \
-ex \"load\" \
-ex \"thread apply all set \\\$pc=&_start\" \
-ex \"thread apply all set \\\$a0=\\\$mhartid\" \
-ex \"thread apply all set \\\$a1=<dtb address>\" \
-ex \"restore u-boot.itb binary 0x200000\" \
-ex \"restore Image binary 0x2000000\" \
-ex \"c\" \
spl/u-boot-spl
"
echo $cmd
eval $cmd
}
The address where the kernel is loaded can be altered by
changing the value of KERNEL_IMAGE_ADDR.
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Using mmc.dtbo from rpi-firmware to switch the controller for the SD
card slot from sdhci to sdhost causes the numbering to change; the
SD card is then not recognized at boot. Add to the range checked.
Signed-off-by: Matthias Brugger <[email protected]>
|
|
If bootloader was updated without running oem format, reboot will cause
boot loop because the SYSTEM stage fails.
Add a final PANIC stage running fastboot to permit recovery.
Signed-off-by: Neil Armstrong <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
This can lead to GPT and BCB errors even if fastboot was selected early
by usb rom boot and the eMMC is blank/invalid.
Signed-off-by: Neil Armstrong <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
Fix dfu_alt_info to use nor1 instead of the device name.
This reverts a part of commit 59bd18d4c4d7 ("configs: synquacer:
Remove mtdparts settings and update DFU setting") because the
commit a4f2d8341455 ("mtd: spi: nor: force mtd name to "nor%d"")
changed the mtd device naming scheme to nor%d.
Signed-off-by: Masami Hiramatsu <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
"TQ-Systems" is written with a dash.
Signed-off-by: Matthias Schiffer <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_LAST_STAGE_INIT
Signed-off-by: Tom Rini <[email protected]>
|
|
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_PL011_SERIAL
CONFIG_PL01X_SERIAL
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MACB
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MD5
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MX6
CONFIG_MX7
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_IMX_BOOTAUX
CONFIG_IMX_THERMAL
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_PROMPT
CONFIG_SYS_PROMPT_HUSH_PS2
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_I2C_EDID
CONFIG_I2C_EEPROM
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_PHYLIB
CONFIG_PHY_ATHEROS
CONFIG_PHY_GIGE
CONFIG_MII
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MISC_INIT_F
CONFIG_MISC_INIT_R
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_TRACE
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY
CONFIG_TRACE_EARLY_ADDR
CONFIG_TRACE_EARLY_SIZE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_FSL_LAYERSCAPE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BITBANGMII
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_DOS_PARTITION
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_E1000
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Tom Rini <[email protected]>
|
|
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
|
|
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
[trini: Migrate CONFIG_EXYNOS7420 as part of merging, so espresso7420
still builds]
Signed-off-by: Tom Rini <[email protected]>
|
|
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
LS1046A-QDS has CONFIG_SPI_FLASH_SST, CONFIG_SPI_FLASH_EON and
CONFIG_SPI_FLASH_STMICRO defines present in header. Move these entries
from header to defconfigs.
Signed-off-by: Kuldeep Singh <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Enable support for update over EFI UpdateCapsule mechanism. This board
doesn't support setting EFI variables after ExitBootservices().
Therefore, we are also enabling EFI_IGNORE_OSINDICATIONS.
Signed-off-by: Michael Walle <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Rename emmc_bootcmd environment variable to sd2_bootcmd
to fix emmc boot on lx2162aqds board.
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_EARLY_INIT_F
CONFIG_BOARD_LATE_INIT
CONFIG_DISPLAY_BOARDINFO
CONFIG_DISPLAY_BOARDINFO_LATE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SPL_DRIVERS_MISC
CONFIG_SPL_ENV_SUPPORT
CONFIG_SPL_GPIO
CONFIG_SPL_I2C
CONFIG_SPL_LDSCRIPT
CONFIG_SPL_LIBCOMMON_SUPPORT
CONFIG_SPL_LIBGENERIC_SUPPORT
CONFIG_SPL_LOAD_FIT_ADDRESS
CONFIG_SPL_MMC
CONFIG_SPL_NAND_SUPPORT
CONFIG_SPL_NO_CPU_SUPPORT
CONFIG_SPL_OS_BOOT
CONFIG_SPL_POWER
CONFIG_SPL_STACK_R
CONFIG_SPL_STACK_R_ADDR
CONFIG_SPL_WATCHDOG
CONFIG_SPL_TEXT_BASE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BMP_16BPP
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_OF_EMBED
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
