| Age | Commit message (Collapse) | Author |
|---|
|
We only install FMPs if a CapsuleUpdate is requested. Since we now have an
ESRT table which relies on FMPs to build the required information, it
makes more sense to unconditionally install them. This will allow userspace
applications (e.g fwupd) to make use of the ERST and provide us with files
we can use to run CapsuleUpdate on-disk
Signed-off-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
We currently define the EFI support of an SMBIOS table as the third bit of
"BIOS Characteristics Extension Byte 1". The latest DMTF spec defines it
on "BIOS Characteristics Extension Byte 2".
Signed-off-by: Ilias Apalodimas <[email protected]>
Remove superfluous assignment.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
- Revert fsl_esdhc_imx using VENDORSPEC_FRC_SDCLK_ON
- Fix data read for dw_mmc
- Increase minimum bus freq for mtk-sd
- Minor cleanup
|
|
Based on the comment in socfpga_soc64_common.h, the intention is for
CONFIG_SYS_MEM_RESERVE_SECURE to be unused. However, in the code we do:
...
and that will evaluate to true. This leads to unwanted code being
compiled. Further, as CONFIG_SYS_MEM_RESERVE_SECURE has not been
migrated to Kconfig, this leads to a mismatch in the size of gd
depending on if we have or have not also had <configs/BOARD.h> also
included yet.
Remove the define as it's not needed.
Cc: Siew Chin Lim <[email protected]>
Cc: Chee Hong Ang <[email protected]>
Cc: Dalon Westergreen <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The original code is in the public domain. Licenses/README states that the
general license for U-Boot is GPL 2.0+. So we can mark the malloc code as
GPL 2.0+ too.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
clock output"
This reverts commit 63756575b42b8b4fb3f59cbbf0cedf03331bc2d2.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Tested-by: Pierre-Jean Texier <[email protected]>
|
|
Change to static about dm function.
They can be used with wrapper functions.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
Use mmc_send_cmd instead of dm_mmc_send_cmd.
It doesn't need to distinguish this function.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
- fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release,
mmc, usb, env, etc for Layerscape boards
- powerpc: Update Maintainers for some boards.
|
|
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
A system clock of 66MHz was chosen for the pg-wcom-ls102xa.
Compared to the Evalboard, this corresponds to a reduction of 1/3.
The system counter clock should have been reduced accordingly,
but that was not the case, so we had a system time that was
1/3 behind the real time.
This patch corrects the system counter clock to
8.333MHz = 66.667MHz / 8.
Signed-off-by: Rainer Boschung <[email protected]>
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.
This patch uses available hwconfig option for updating ls102x device
disable configuration.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.
For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.
Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <[email protected]>
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <[email protected]>
Acked-by: Michael Walle <[email protected]> [for kontron-sl28]
Reviewed-by: Priyanka Jain <[email protected]>
|
|
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20210616
-------------------
- imxrt : fixes, USB, imxrt1020-evk
- imx8m:
fix for verdin-imx8mm
Add conga-QMX8 board
- imx6 :
documentation for pico-imx6:
Add SeeedStudio NPI-IMX6ULL Support
ventana: DM PCI
- imx7d:
added SMEGW01 board
CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765
|
|
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <[email protected]>
Signed-off-by: Mian Yousaf Kaukab <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <[email protected]>
Cc: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 49C
Reset cause: POR
Model: Seeed NPi iMX6ULL Dev Board with NAND
Board: Seeed NPi i.MX6ULL Dev Board
DRAM: 512 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Navin Sankar Velliangiri <[email protected]>
Note:
Changes in v2:
* removed unnecessary space in imx6ull-seeed-npi-imx6ull-dev-board.dts file.
* Used SZ_2M for CONFIG_SYS_MALLOC_LEN size allocation.
|
|
Add i.MX8QM qmx8 congatec board support
U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Congatec QMX8 Qseven series
Board: conga-QMX8
Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9
Boot: SD2
DRAM: 6 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial@5a060000
Out: serial@5a060000
Err: serial@5a060000
switch to partitions #0, OK
mmc2 is current device
Net:
Error: ethernet@5b040000 address not set.
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Oliver Graute <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: Oleksandr Suvorov <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <[email protected]>
|
|
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Add dts support for fu740. The HiFive Unmatched support is based on
fu740 cpu and drivers in following patch set.
Signed-off-by: Green Wan <[email protected]>
[greentime.hu: set fu740 speed to 1.2GHz]
Signed-off-by: Greentime Hu <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
"TCG PC Client Platform Firmware Profile Specification"
requires to measure every attempt to load and execute
a OS Loader(a UEFI application) into PCR[4].
This commit adds the PE/COFF image measurement, extends PCR,
and appends measurement into Event Log.
Acked-by: Ilias Apalodimas <[email protected]>
Tested-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Masahisa Kojima <[email protected]>
Replace CONFIG_HASH_CALCULATE by CONFIG_HASH
Fix conversions between pointers and u64.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-ti
- Fix reset for AM64 platforms
- Enable networking PHY driver for AM64
- Fix default R5F cluster setting in J7
|
|
MLO has increased to a size greater than the allocated
128 kB in dfu_alt_info_emmc and _mmc.
Therefore, double the allocated size for MLO.raw in
the default environment.
Signed-off-by: Faiz Abbas <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
ut_asserteq_strn is defined twice. Remove one definition.
Fixes: 33d7edfd5f ("test: Add a way to check part of a console line or skip it")
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <[email protected]>
|
|
When building with LTO, the system libc's `errno` variable used in
arch/sandbox/cpu/os.c conflicts with U-Boot's `errno` (defined in
lib/errno.c) with the following error:
.../ld: errno@@GLIBC_PRIVATE: TLS definition in /lib64/libc.so.6
section .tbss mismatches non-TLS reference in
/tmp/u-boot.EQlEXz.ltrans0.ltrans.o
To avoid this conflict use different asm label for this variable when
CONFIG_SANDBOX is enabled.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add macro __efi_runtime_rodata, for const variables with similar purpose
as those using __efi_runtime_data.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Document the macros __efi_runtime and __efi_runtime_data in Sphinx
style.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
When linking with LTO, the compiler complains about type mismatch of
variables `__efi_runtime_start`, `__efi_runtime_stop`,
`__efi_runtime_rel_start` and `__efi_runtime_rel_stop`:
include/efi_loader.h:218:21: warning: type of ‘__efi_runtime_start’
does not match original
declaration [-Wlto-type-mismatch]
218 | extern unsigned int __efi_runtime_start, __efi_runtime_stop;
| ^
arch/sandbox/lib/sections.c:7:6: note: ‘__efi_runtime_start’ was
previously declared here
7 | char __efi_runtime_start[0] __attribute__((section(".__efi_run
| ^
Change the type to char[] in include/efi_loader.h.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Use UNIQUE_ID in the __ADDRESSABLE macro.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Signed-off-by: Stefan Chulski <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <[email protected]>
|
|
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <[email protected]>
|
|
This simplifies the PLL creation process, since we don't have to pass all
the parameters individually.
Signed-off-by: Sean Anderson <[email protected]>
|
