| Age | Commit message (Collapse) | Author |
|---|
|
Link to zynqmp common file is incorrect. Fix it by removing the whole
link because it is visible from the file where to look at it.
Signed-off-by: Michal Simek <[email protected]>
|
|
Define minimum sdhci frequency for ep, as not defining
it causes the divisor to be 2048 as per sd version but
keeping clock very low on ep causes command failures.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Clean up config and use Kconfig more.
Signed-off-by: Michal Simek <[email protected]>
|
|
Add bitstream type BIT_NONE to the bitstream type
enum. This might be useful while loading bitstreams
in respective drivers.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
board_init() is in final elf file but it is not called at all.
Use board_init_late() instead and call gpio_init() from it.
Signed-off-by: Michal Simek <[email protected]>
|
|
Cleanup board file.
Signed-off-by: Michal Simek <[email protected]>
|
|
Do not setup ram start/size in board file. Read it from DT instead.
Signed-off-by: Michal Simek <[email protected]>
|
|
Cleanup board file.
Signed-off-by: Michal Simek <[email protected]>
|
|
And enable it via defconfig by default.
Signed-off-by: Michal Simek <[email protected]>
|
|
Systemace is ancient IP which is not tested. Remove it from default
configuration.
Signed-off-by: Michal Simek <[email protected]>
|
|
Cleanup board specific file.
Signed-off-by: Michal Simek <[email protected]>
|
|
Enable driver by default for all platforms.
Signed-off-by: Michal Simek <[email protected]>
|
|
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Move driver to DM.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Prepare for DM move.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Move driver to DM.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
To solve enabling ETH_DM where ksz90x1_reg_field is defined only when
additional Micrel type is defined.
Signed-off-by: Michal Simek <[email protected]>
|
|
Cleanup board configuration.
Signed-off-by: Michal Simek <[email protected]>
|
|
Microblaze is uses uartlite or uart16550 as console drivers.
Signed-off-by: Michal Simek <[email protected]>
|
|
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Thomas Chou <[email protected]>
|
|
Preparation of moving to DM. Uartlite ignores baudrate setting.
Signed-off-by: Michal Simek <[email protected]>
|
|
Take it from DT instead.
Signed-off-by: Michal Simek <[email protected]>
|
|
-Remove UART address (It is now part of the dts).
-Include dummy ns16550 clock
-Fix address to last test
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
-Fix typos (runnining -> running)
-Increase default size
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
-Fix typos (runnining -> running)
-Increase default size
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
Now that there is only one header file for all ppc405 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
Now that there is only one header file for all ppc440 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
|
|
Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Acked-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Some of the register definitions are duplicated. Drop them.
Signed-off-by: Chen-Yu Tsai <[email protected]>
Acked-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Adds poweroff support for axp221 pmic.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
|
|
Enabling CONFIG_DISPLAY breaks building for some architectures
(microblaze-generic), so we disable CONFIG_DISPLAY in Kconfig
by default and enable this option in defconfigs. CONFIG_DISPLAY
depends on CONFIG_I2C_EDID, so add and enable it in defconfigs, too.
Signed-off-by: Anatolij Gustschin <[email protected]>
Reported-by: Bin Meng <[email protected]>
Cc: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Bin Meng <[email protected]>
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
|
|
|
|
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.
Signed-off-by: Ying Zhang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
|
|
Since we are manipulating GPIO 189 to determine the board type, we
need to enable the GPIO Bank 6.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Do not undefine CONFIG_BOOTDELAY, so board can boot without user
intervention.
Signed-off-by: Ladislav Michl <[email protected]>
Acked-by: Enric Balletbo i Serra <[email protected]>
|
|
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add function to poll register waiting for specific bit(s).
Similar functions are implemented in few drivers - they are almost
identical and can be generalized.
Signed-off-by: Mateusz Kulikowski <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This is already defined in ide.h, which part.h includes. So we don't need
the duplicate typedef. At least with my old blackfin gcc 4.3.5 tool chain,
this causes an error.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Andreas Bießmann <[email protected]>
|
|
This commit 4bdcbe60a142b08eefccb0e326a37ba81d3389e8 removes reset_cpu
which breaks SPL build when DEBUG macro defined.
"
arch/arm/lib/built-in.o: In function `do_reset':
~/uboot/arch/arm/lib/reset.c:45: undefined reference to `reset_cpu'
scripts/Makefile.spl:244: recipe for target 'spl/u-boot-spl' failed
"
Enable CONFIG_SPL_WATCHDOG_SUPPORT to fix this issue.
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Tim Harvey <[email protected]>
Acked-by: Eric Nelson <[email protected]>
|
|
Add pinmux settings.
Add related macro definitions.
Nand pin conflicts with emmc, so if want to enable nand, need to do
hardware rework. After hardware rework, define CONFIG_NAND_MXS in
board header file.
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add CONFIG_SPI_FLASH_STMICRO to let qspi driver can detect the
qspi chips.
"
=> sf probe
SF: Detected N25Q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
"
Signed-off-by: Peng Fan <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
Support uncompressing zImage which is larger than 8M.
Signed-off-by: Peng Fan <[email protected]>
Cc: Peter Robinson <[email protected]>
Cc: Volodymyr Riazantsev <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Adrian Alonso <[email protected]>
Cc: Stefano Babic <[email protected]>
|
