| Age | Commit message (Collapse) | Author |
|---|
|
- changes in pico-* boards
- fix imx6ull pinmux
|
|
- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes and enhancements to the pxa3xx NAND driver
- Fixes for the UART boot mode in kwboot
- Misc minor changes to other 32bit and 64bit boards
|
|
The Clearfog SOM can optionally have eMMC installed. Enable support for
eMMC boot partitions by default.
Signed-off-by: Baruch Siach <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Add definitions for CONFIG_ENV_SPI_BUS and CONFIG_ENV_SPI_CS
to Armada-388-GP board configuration
Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.
This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.
This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.
Signed-off-by: Marek Behun <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Detect the SD/eMMC boot device at run-time. Load the environment from
the boot deice, as well as save to it.
Leave the environment offset the same as in the SPI flash.
Make SD/eMMC 0 the default environment device when the boot device is
not detected.
Cc: Konstantin Porotchkin <[email protected]>
Signed-off-by: Baruch Siach <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The default bootdelay of 3 seconds is good enough and there is no need
to duplicate it in CONFIG_EXTRA_ENV_SETTINGS.
Signed-off-by: Evgeni Dobrev <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
- MPC83xx device tree additions (CPU and RAM)
- Fix sandbox build error
- Sync bitrev with Linux
- Various ofnode/DT improvements
|
|
The comment of child_pre_probe, one of the 'struct uclass_driver'
members, is currently missing.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This adds the device tree to the DFU and bootmenu environment setting.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
This adds the device tree to the DFU and bootmenu environment setting.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Signed-off-by: Stefano Babic <[email protected]>
|
|
Adds ofnode_by_prop_value() to search for nodes with a given property
and value, an ofnode version of fdt_node_offset_by_prop_value().
Signed-off-by: Jens Wiklander <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add a method to probe all CPUs of the board.
Signed-off-by: Mario Six <[email protected]>
|
|
Documentation in cpu.h is not in kernel-doc format. Change it to comply
with it.
Signed-off-by: Mario Six <[email protected]>
|
|
When the DM CPU drivers are active, printing information about a CPU
should be delegated to a matching driver.
Hence, add a static print_cpuinfo that implements this delegation when
DM CPU drivers are active.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Mario Six <[email protected]>
Changed condition to CONFIG_IS_ENABLED(CPU):
Signed-off-by: Simon Glass <[email protected]>
|
|
The documentation in init.h is not in kernel-doc format. Fix this.
Signed-off-by: Mario Six <[email protected]>
|
|
Add a clock driver for the MPC83xx architecture.
Signed-off-by: Mario Six <[email protected]>
|
|
It's useful to have the reset status of the SoC printed out during reset
(e.g. to learn whether the reset was caused by software or a watchdog).
As a first step to implement this, add a get_status method to the
sysreset class, which enables the caller to get printable information
about the reset status (akin to get_desc in the CPU uclass).
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Mario Six <[email protected]>
|
|
Add a RAM driver for the MPC83xx architecture.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Mario Six <[email protected]>
|
|
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
|
|
This will add support for a baud rate of 57600.
Signed-off-by: Christian Gmeiner <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
|
|
The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .
Signed-off-by: Marek Vasut <[email protected]>
|
|
The header contains only the TMU register layout, just inline it
into the TMU timer implementation and drop the header completely.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2,
while the old SH parts use CONFIG_SYS_CLK_FREQ directly.
Just put this into the TMU implementation and drop the
CONFIG_SH_TMU_CLK_FREQ config option.
Signed-off-by: Marek Vasut <[email protected]>
|
|
This function just returns CONFIG_SH_TMU_CLK_FREQ, use the constant
directly instead.
Signed-off-by: Marek Vasut <[email protected]>
|
|
This constant is always 4 , for all boards that exist. Define it
once in arch/sh/lib/time.c and remove it from the configs.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The dtb should be embedded in the u-boot-spl image so that
the CONFIG_SPL_TARGET of spl/u-boot-spl.hex includes it.
This also affects the main u-boot image, so adjust
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME to u-boot.img which now
also includes the dtb.
Signed-off-by: Dalon Westergreen <[email protected]>
|
|
Stratix10 combines the u-boot-spl image into the fpga configuration
bitstream so that the SDM can load the processors memory. This
process requires a hex format of the u-boot-spl image.
CONFIG_SPL_TARGET is set to "spl/u-boot-spl.hex"
Signed-off-by: Dalon Westergreen <[email protected]>
|
|
I added in the CONFIG_MISC_INIT_R line by mistake when applying the
previous patch, fix.
Signed-off-by: Tom Rini <[email protected]>
|
|
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx6ul does not have a GPIO for selecting Falcon versus normal
mode, enter in Falcon mode when the customer selects the
CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
The CONFIG_FSL_USDHC is defined inside "mx6_common.h", which is
already included in this file.
Signed-off-by: Otavio Salvador <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
This rework the DFU settings so it supports the SPL and U-Boot image,
as well as the single partition layout we are using by default.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Currently the baseboards do not offer a way to autodetect which one is
in use, so we ask the user if no value has been set.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.
Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.
Currently only the 256MB is tested/supported.
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: Fabio Berton <[email protected]>
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: Otavio Salvador <[email protected]>
|
|
DM_I2C_COMPAT is somehow being enabled outside of Kconfig, so
this explicitly undefines it in the header file, and brackets
the I2C initialization around an #ifdef to not manually
initialize the I2C controller when the DM_I2C is enabled.
Signed-off-by: Adam Ford <[email protected]>
Tested-by: Derald D. Woods <[email protected]>
|
|
The serial port was being manually configured during SPL build,
however in preparation to allow DM in SPL, this needs to change
to be based on whether or not DM_SERIAL is enabled because, soon
the assumption that SPL means no DM may not be accurate.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The DA850-EVM supports booting from NAND when used with the
UI expander board. da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.
Signed-off-by: Adam Ford <[email protected]>
|
|
|
|
Add the minimum dt nodes required to boot. These nodes
will get deleted as kernel gets these nodes added in the
main dts files.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Create a basic U-Boot environment that allows the automatic loading
of a Linux Kernel located at /boot/Image and an associated device tree
blob located at /boot/k3-am654-base-board.dtb from the secondary
partition of an ext4-formatted SD card on the AM654x EVM. Furthermore
the boot.scr and uEnv.txt detection and loading schemes are supported
in a manner already known from other TI platforms.
Note that this is intended to be a starting point to enable initial
board use and will most certainly get extended and refactored as
different boot media become available.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Andreas Dannenberg <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <[email protected]>
|
|
Existing rproc_init() api tries to initialize all available
remoteproc devices. This will fail when there is dependency
among available remoteprocs. So introduce a separate api
that allows to initialize remoteprocs individually based
on id.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Secure Proxy module manages hardware threads that are meant
for communication between the processor entities. Adding
support for this driver.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Signed-off-by: Andreas Dannenberg <[email protected]>
|
|
Sometimes mbox controllers wants to store private data in
mbox_chan so that it can be used at a later point of time.
Adding support for hooking private data.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
There are cases where there are more than one power domain
attached to the device inorder to get the device functional.
So add support for enabling power domain based on the index.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
