| Age | Commit message (Collapse) | Author |
|---|
|
Reading doc/README.distro , we see platform needs to set
pxefile_addr_r to support distro boot.
Signed-off-by: Riku Voipio <[email protected]>
|
|
In commit e163a931af34 ("cmd: gpt: backup boot code before writing MBR")
there was added the procedure for storing old boot code when doing "gpt
write". But instead of storing just backup code, the whole MBR was
stored, and only specific fields were replaced further, keeping
everything else intact. That's obviously not what we want.
Fix the code to actually store only old boot code and zero out
everything else. This fixes next testing case:
=> mmc write $loadaddr 0x0 0x7b
=> gpt write mmc 1 $partitions
In case when $loadaddr address and further memory contains 0xff, the
board was bricked (ROM-code probably didn't like partition entries that
were clobbered with 0xff). With this patch applied, commands above don't
brick the board.
Signed-off-by: Sam Protsenko <[email protected]>
Cc: Alejandro Hernandez <[email protected]>
Tested-by: Andy Shevchenko <[email protected]>
|
|
This updates the LEGO MINDSTORMS EV3 boot script to try loading a
uEnv.txt file and a da850-lego-ev3.dtb device tree during boot.
Signed-off-by: David Lechner <[email protected]>
|
|
This removes the unused clock and RAM config options that were cargo-
culted when this board was copied from the DA850 EVM.
Signed-off-by: David Lechner <[email protected]>
|
|
This disables networking related items in the config. The EV3 does not have
any networking hardware, so this is wasted space.
Signed-off-by: David Lechner <[email protected]>
|
|
This increases the kernel image to 4M and the rootfs image to 10M.
It is getting hard to get a kernel image to fit in 3M.
Signed-off-by: David Lechner <[email protected]>
|
|
The u-boot binary sits in flash immediately before the environment.
Don't allow the binary size to grow into the environment space.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The u-boot binary sits in flash immediately before the environment.
Don't allow the binary size to grow into the environment space.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The SBx81LIFKW boards connect to the internal chassis management network
via a Marvell 88e6097 L2 switch. The chassis connections are direct
serdes on ports 8 and 9 with a RGMII interface on port 10 connected to
the CPU MAC.
For debugging purposes ports 0 and 1 are also taken out to headers on
the board. Because the debug interfaces are sometimes connected to with
straight ribbon cables we need to run them at 10Mbps.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Chris Packham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
This switches the clearfog boards to use DM based gpio and i2c
drivers. The io expanders are configured via their device-tree
entries.
Signed-off-by: Jon Nettleton <[email protected]>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <[email protected]>
Reviewed-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The a38x sata interfaces run in ahci mode and can
be accessed via the scsi command.
Signed-off-by: Jon Nettleton <[email protected]>
[baruch: rebase on current upstream]
Signed-off-by: Baruch Siach <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The default value with distro_bootcmd is 2 seconds, which is
reasonably fast, and provides a consistent experience across platforms
supporting distro_bootcmd.
The current bootdelay value of 0 seconds is a bit challenging to
interrupt when desired.
Signed-off-by: Vagrant Cascadian <[email protected]>
Acked-by: Heinrich Schuchardt <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
|
|
Patch queue for efi - 2018-06-03
A number of fixes and feature completeness work this time around:
- Fix sunxi GOP reservation
- Fix cursor position
- Fix efi_get_variable
- Allow more selftest parts to build on x86_64
- Allow unaligned memory access on armv7
- Implement ReinstallProtocolInterface
- More sandbox preparation
|
|
The magic value that disables relocation is dependent on the CPU word
size, so the current 'ffffffff' is doing the wrong thing on aarch64.
Signed-off-by: Tuomas Tynkkynen <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
This exported function should have a comment describing what it does. Also
it should really be removed in favour of device_remove(), which handles
this sort of thing now. Add a comment with a TODO.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
This undocumented function relies on arch-specific code to declare a nop
weak version. Add the weak function in common code instead to avoid having
to duplicate the same function in each arch.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
Add an implementation of setjmp() and longjmp() which rely on the
underlying host C library. Since we cannot know how large the jump buffer
needs to be, pick something that should be suitable and check it at
runtime. At present we need access to the underlying struct as well.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
Clarify the operation of this code with some additional comments.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.
This patch adds an empty weak function unaligned_access() that can be
overridden by an architecture specific routine.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
The definitons of the variable services are adjusted:
- use efi_uintn_t instead of unsigned long
- use u16 * instead of s16 * for Unicode strings
- correct definition of QueryVariableInfo
- rename efi_get_next_variable to efi_get_next_variable_name
Signed-off-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
|
|
|
|
Xilinx changes for v2018.07 second pull
zynqmp:
- Show reset reason
- Remove emulation platform
- Update pmufw version
- Simplify mmc bootmode
- Remove dc2 useless configuration file
- Cleanup mini config
- Defconfig syncup
- zcu100, zcu104 and zcu111 dts fixes
xilinx:
- Use live-tree functions in some drivers
- Add support for Avnet Minized and Antminer S9
fpga:
- Add secure bitstream loading support
mmc:
- Add hs200 mode support
usb xhci:
- Header fix
|
|
Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Daniel Schwierzeck <[email protected]>
Signed-off-by: Daniel Schwierzeck <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
|
|
This patch adds support for loading secure bitstreams on ZynqMP
platforms. The secure bitstream images has to be generated using
Xilinx bootgen tool.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
This patch adds support to load secure bitstreams(authenticated or
encrypted or both). As of now, this feature is added and tested only
for xilinx bitstreams and the secure bitstream was generated using
xilinx bootgen tool, but the command is defined in more generic way.
Command example to load authenticated and device key
encrypted bitstream is as follows
"fpga loads 0 100000 2000000 0 1"
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support for the R8A77990 Ebisu board.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Add clock tables for R8A77990 E3 SoC .
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Enable MTD partitioning support on Gen2 boards with SPI NORs.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Here we do a couple of minor fixes like:
- Move .ivt section to the very beginning of the image
by default which allows us to use that image put right
at reset vector (usually 0x0)
- Improve relocation fix-up which became required once
we moved .ivt and understood a problem with existing implementation
where we relied on a particular placement of sections.
Now we don't care about placement because we just explicitly
check for .text and in case of ARCompact .ivt sections
- Re-implemnt do_reset() such that it calls reset_cpu() which
could implmented for a particular board
And hte most important part we introduce support for yet another
devboard from Synopsys - EMDK.
|
|
Synopsys DesignWare ARC EM Development Kit (ARC EMDK) is
an FPGA-based development platform from Synopsys aimed to speed-up
development of software for ARC EM cores and entire subsystems based on
ARC EM like Data Fusion, Secure and Sensor & Control subsystems.
U-Boot is supposed to be used as a primary bootloader on EMDK allowing
users to easily load and start their application from micro-SD card.
Signed-off-by: Alexey Brodkin <[email protected]>
|
|
This adds the following commits from upstream:
aadd0b65c987 checks: centralize printing of property names in failure messages
88960e398907 checks: centralize printing of node path in check_msg
f1879e1a50eb Add limited read-only support for older (V2 and V3) device tree to libfdt.
37dea76e9700 srcpos: drop special handling of tab
65893da4aee0 libfdt: overlay: Add missing license
962a45ca034d Avoid installing pylibfdt when dependencies are missing
cd6ea1b2bea6 Makefile: Split INSTALL out into INSTALL_{PROGRAM,LIB,DATA,SCRIPT}
51b3a16338df Makefile.tests: Add LIBDL make(1) variable for portability sake
333d533a8f4d Attempt to auto-detect stat(1) being used if not given proper invocation
e54388015af1 dtc: Bump version to v1.4.6
a1fe86f380cb fdtoverlay: Switch from using alloca to malloc
c8d5472de3ff tests: Improve compatibility with other platforms
c81d389a10cc checks: add chosen node checks
e671852042a7 checks: add aliases node checks
d0c44ebe3f42 checks: check for #{size,address}-cells without child nodes
18a3d84bb802 checks: add string list check for *-names properties
8fe94fd6f19f checks: add string list check
6c5730819604 checks: add a string check for 'label' property
a384191eba09 checks: fix sound-dai phandle with arg property check
b260c4f610c0 Fix ambiguous grammar for devicetree rule
fe667e382bac tests: Add some basic tests for the pci_bridge checks
7975f6422260 Fix widespread incorrect use of strneq(), replace with new strprefixeq()
fca296445eab Add strstarts() helper function
cc392f089007 tests: Check non-matching cases for fdt_node_check_compatible()
bba26a5291c8 livetree: avoid assertion of orphan phandles with overlays
c8f8194d76cc implement strnlen for systems that need it
c8b38f65fdec libfdt: Remove leading underscores from identifiers
3b62fdaebfe5 Remove leading underscores from identifiers
2d45d1c5c65e Replace FDT_VERSION() with stringify()
2e6fe5a107b5 Fix some errors in comments
b0ae9e4b0ceb tests: Correct warning in sw_tree1.c
Commit c8b38f65fdec upstream ("libfdt: Remove leading underscores from
identifiers") changed the multiple inclusion define protection, so the
kernel's libfdt_env.h needs the corresponding update.
Signed-off-by: Rob Herring <[email protected]>
[ Linux commit: 9130ba884640328bb78aaa4840e5ddf06ccafb1c ]
[erosca: - Fixup conflicts in include/linux/libfdt_env.h caused by v2018.03-rc4
commit b08c8c487083 ("libfdt: move headers to <linux/libfdt.h>
and <linux/libfdt_env.h>")
- Fix build errors in lib/libfdt/fdt_ro.c, tools/libfdt/fdt_rw.c by:
- s/_fdt_mem_rsv/fdt_mem_rsv_/
- s/_fdt_offset_ptr/fdt_offset_ptr_/
- s/_fdt_check_node_offset/fdt_check_node_offset_/
- s/_fdt_check_prop_offset/fdt_check_prop_offset_/
- s/_fdt_find_add_string/fdt_find_add_string_/]
Signed-off-by: Eugeniu Rosca <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Masahiro Yamada <[email protected]>
|
|
This is control board on Bitmain Antminer S9.
There are 3 board variables with 256MB, 512MB and 1024MB DDR.
DDR memory is automatically detected with using get_with using
get_ram_size().
Bitmain is using 16MB space for FPGA which is handled via
reserved-memory. Also U-Boot is allocating 16B for storing bootcounts.
Watchdog is started but never service in U-Boot.
SPL MMC is working. SPL NAND is not working because it is not supported
as of now.
Signed-off-by: Ezequiel Garcia <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
CMD_UNZIP is already disabled via Kconfig.
Signed-off-by: Michal Simek <[email protected]>
|
|
There is no reason to keep empty config file in the tree that's why
remove it.
Signed-off-by: Michal Simek <[email protected]>
|
|
|
|
Introduce 'oem format' which matches the USB implementation, guard this
with CONFIG_FASTBOOT_CMD_OEM_FORMAT so that you can configure it out.
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Merge UDP fastboot support from AOSP:
https://android.googlesource.com/platform/external/u-boot/+/android-o-mr1-iot-preview-8
Signed-off-by: Alex Kiernan <[email protected]>
Signed-off-by: Alex Deymo <[email protected]>
Signed-off-by: Jocelyn Bohr <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add fs_get_type_name so we can get the current filesystem type.
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
Rename fb_mmc_flash_write/fb_mmc_erase/fb_nand_flash_write/fb_nand_erase to
fastboot_... as they form a public interface
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Move FASTBOOT_VERSION to include/fastboot.h so when we merge the UDP code
we only have one definition.
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches
all other fastboot code in the global name space. Fix the guards around
them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT.
Move the weak implementation of fastboot_set_reboot_flag to fb_common.c
so we can call it from non-USB fastboot code.
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Add drivers/fastboot/fb_common.c, where fastboot_okay/fail are implemented
so we can call them from a non-USB implementation.
Introduce fastboot_response which takes varargs parameters so we can
use it to generate formatted response strings. Refactor fastboot_okay/fail
to use it.
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
Add the response string as a parameter to fastboot_okay/fail, instead
of modifying a global, to match the contract expected by the AOSP
U-Boot code.
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Joe Hershberger <[email protected]>
|
|
|
|
Android documentation defines the recommended image format for storing
DTB/DTBO files in a single dtbo.img image. This patch includes the
latest header file with the struct definitions for this format from
AOSP.
The header was adapted to U-Boot's coding style and the function
declarations were removed.
Signed-off-by: Alex Deymo <[email protected]>
[trini: Change SDPX tag location]
Signed-off-by: Tom Rini <[email protected]>
|
|
This was being used by some Marvell boards to enable some file system
related features (many of which have already been moved to Kconfig).
Make the future migration of the final 2 or 3 config options easier by
expanding #define CONFIG_SYS_MVFS into the options that it enables and
remove CONFIG_SYS_MVFS.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
