| Age | Commit message (Collapse) | Author |
|---|
|
When the generic filesystem load command "fsload" was written, I felt
that "load" was too generic of a name for it, since many other similar
commands already existed. However, it turns out that there is already
an "fsload" command, so that name cannot be used. Rename the new
"fsload" to plain "load" to avoid the conflict. At least anyone who's
used a Basic interpreter should feel familiar with the name!
Signed-off-by: Stephen Warren <[email protected]>
|
|
Commit 045fa1e "fs: add filesystem switch libary, implement ls and
fsload commands" unified the implementation of fatload and ext*load
with the new command fsload. However, this altered the interpretation
of command-line numbers from always being base-16, to requiring a "0x"
prefix for base-16 numbers. Enhance do_fsload() to allow commands to
specify which base to use.
Use base 0, thus requiring a "0x" prefix for the new fsload command.
This feels much cleaner than assuming base 16.
Use base 16 for the pre-existing fatload and ext*load to prevent a
change in behaviour.
Use base 16 exclusively for the loadaddr environment variable, since
that variable is interpreted in multiple places, so we don't want the
behaviour to change.
Update command help text to make it clear where numbers are assumed to
be hex, and where an explicit "0x" prefix is required.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Benoît Thébaudeau <[email protected]>
|
|
* add CONFIG_SYS_CACHELINE_SIZE to eb_cpux9k2 board config header
* dissable dcache (CONFIG_SYS_DCACHE_OFF) for eb_cpux9k2
Signed-off-by: Jens Scharsig (BuS Elektronik) <[email protected]>
|
|
|
|
Enable AHCI driver for Intel SATA devices.
Signed-off-by: Simon Glass <[email protected]>
|
|
Writes in u-boot are so rare, and the logic to know when is
the last write and do a flush only there is sufficiently
difficult. Just do a flush after every write. This incurs,
usually, one extra flush when the rare writes do happen.
Signed-off-by: Marc Jones <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
In the structure returned by the ATA identify device command, there are two
fields which describe the device capacity. One is a 32 bit data type which
reports the number of sectors as a 28 bit LBA, and the other is a 64 bit data
type which is for a 48 bit LBA. If the device doesn't support 48 bit LBAs,
the small value is the only value with the correct size. If it supports more,
if the number of sectors is small enough to fit into 28 bits, both fields
reflect the correct value. If it's too large, the smaller field has 28 bits of
1s, 0xfffffff, and the other field has the correct value.
The AHCI driver is implemented by attaching to the generic SCSI code and
translating on the fly between SCSI binary data structures and AHCI data
structures. It responds to requests to execute specific SCSI commands by
executing the equivalent AHCI commands and then crafting a response which
matches what a SCSI disk would send.
The AHCI driver now considers both fields and chooses the correct one when
implementing both the SCSI READ CAPACITY (10) and READ CAPACITY (16) commands.
Signed-off-by: Gabe Black <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
- print the correct speed
- print all the AHCI capability flags
(information taken from Linux kernel driver)
- clean up some comments
For example, this might show the following string:
AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
Signed-off-by: Stefan Reinauer <[email protected]>
Commit-Ready: Stefan Reinauer <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
Tested-by: Stefan Reinauer <[email protected]>
|
|
Add a new function to find out the number of available SCSI disks. Also
set the 'scsidevs' environment variable after each scan.
Signed-off-by: Stefan Reinauer <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
This includes were outside an #ifdef CONFIG_PPC, but there is not reason
to exclude powerpc from using them.
Move the declaration outside the #ifdef.
Signed-off-by: Simon Glass <[email protected]>
|
|
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this. It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.
Signed-off-by: Tom Rini <[email protected]>
|
|
CONFIG_ENV_VARS_UBOOT_CONFIG creates environment variables indicating
which configuration U-Boot was built for. Some U-Boot binaries run on
multiple boards, and hence this information may not uniquley describe
the HW that U-Boot is actually running on. Another patch introduces
environment variable board_name to represent that. In order to avoid
scripts having to check $board_name, use it if set, and then fall back
to using $board, make CONFIG_ENV_VARS_UBOOT_CONFIG also set a default
value for board_name, so that variable is always available.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Commit 1db7377a70a8d931c32648e717695133120d5456 fixes the gen_atmel_mci driver
to be able to use multi block access for avr32. Therefore remove the setting
which forces single block access.
This also adds a huge performace gain for mmc access:
---8<---
Loading file "/boot/uImage" from mmc device 0:1
1830666 bytes read in 1293 ms (1.3 MiB/s)
--->8---
vs.
---8<---
Loading file "/boot/uImage" from mmc device 0:1
1830666 bytes read in 237 ms (7.4 MiB/s)
--->8---
Signed-off-by: Andreas Bießmann <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
|
|
Signed-off-by: Raphael Assenat <[email protected]>
[trini: Squash boards.cfg / MAINTAINERS change into main patch]
Signed-off-by: Tom Rini <[email protected]>
|
|
Based on previous work by: Alistair Buxton <[email protected]>
Signed-off-by: Pali Rohár <[email protected]>
Cc: Ивайло Димитров <[email protected]>
|
|
* Code copied from linux kernel 3.0.0 from file include/linux/i2c/twl.h
* commit 6523b148b44be38d89c2ee9865d34da30d9f5f1c
Signed-off-by: Pali Rohár <[email protected]>
|
|
Implement "ls" and "fsload" commands that act like {fat,ext2}{ls,load},
and transparently handle either file-system. This scheme could easily be
extended to other filesystem types; I only didn't do it for zfs because
I don't have any filesystems of that type to test with.
Replace the implementation of {fat,ext[24]}{ls,load} with this new code
too.
Signed-off-by: Stephen Warren <[email protected]>
|
|
This makes the FAT and ext4 filesystem implementations build if
CONFIG_FS_{FAT,EXT4} are defined, rather than basing the build on
whether CONFIG_CMD_{FAT,EXT*} are defined. This will allow the
filesystems to be built separately from the filesystem-specific commands
that use them. This paves the way for the creation of filesystem-generic
commands that used the filesystems, without requiring the filesystem-
specific commands.
Minor documentation changes are made for this change.
The new config options are automatically selected by the old config
options to retain backwards-compatibility.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Benoît Thébaudeau <[email protected]>
|
|
Change tegra SPL to use common SPL framework. Any tegra specific
initialization is now done in spl_board_init() instead of
board_init_f()/board_init_r(). Only one SPL boot target is supported
on tegra, which is boot to RAM image. jump_to_image_no_args() must be
overridden on tegra so the host CPU can be initialized.
Signed-off-by: Allen Martin <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Tested-by: Lucas Stach <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
For Tegra, the SPL and main U-Boot are concatenated together to form a
single memory image. Hence, the maximum SPL size is the different in
TEXT_BASE for SPL and main U-Boot. Instead of manually calculating
SPL_MAX_SIZE based on those two TEXT_BASE, which can lead to errors if
one TEXT_BASE is changed without updating SPL_MAX_SIZE, simply perform
the calculation automatically.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Acked-by: Allen Martin <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Add the missing bits to the Tegra NAND driver to make ONFI detection work
properly.
Also add it to the Tegra default config, as it seems to be a reasonable thing
to have it available on all boards that use any kind of NAND.
Signed-off-by: Lucas Stach <[email protected]>
Acked-by: Scott Wood <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The device tree already contains the required configuration for both the
USB1 and USB3 ports. Enable the required configuration options to enable
both these ports, which in turn allows the USB1 port to be used.
Note that on a true Seaboard, this port is typically used as a device
port hosting Tegra's USB recovery protocol. However, on the Springbank
derivative, this port is the only external USB port, so we enable it as
a host port so that USB peripherals may be used. Enabling this port in
U-Boot as a host port doesn't prevent the port from reverting to a
device port when the CPU is reset into recovery mode.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The ULPI port is routed onto pins on the mini PCI Express connector. A
standard breakout board may be used to access the port.
* Add required DT entries to configure the ULPI port.
* Setup up the ULPI pinmux in the board code.
* Enable multiple USB controller and ULPI support in the board config.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Currently, Tegra's default environment uses non-standard variables to define
where boot scripts should load the kernel, FDT, and initrd. This change both
changes the variable names to match those described in U-Boot's README, and
shuffles their values around a little so that the values make a little more
sense; see comments in the patch for rationale behind the values chosen.
Note that this patch does remove the old non-standard variable "fdt_load" from
the default environment, so this patch requires people to change their boot
scripts.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This define indicates the size of the memory region where it is safe
to place data passed to the Linux kernel (ATAGs, DTB, initrd). The
value needs to be:
a) Less than or equal to RAM size.
b) Small enough that the area is not within the kernel's highmem region,
since the kernel cannot access ATAGs/DTB/initrd from highmem.
c) Large enough to hold the kernel+DTB+initrd.
256M seems large enough for (c) in most circumstances, and small enough
to satisfy (a) and (b) across any possible Tegra board. Note that the
user can override this value via environment variable "bootm_mapsize"
if needed.
The advantage of defining BOOTMAPSZ is that we no longer need to define
variable fdt_high in the default environment. Previously, we defined
this to prevent the DTB from being relocated to the very end of RAM,
which on most Tegra systems is within highmem, and hence which would
cause boot failures. A user can still define this variable themselves
if they want the FDT to be either left in-place wherever loaded, or
copied to some other specific location. Similarly, there should no
longer be a strict requirement for the user to define initrd_high if
using an initrd.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This adds board support for the Toradex Colibri T20 module.
Working functions:
- SD card boot
- USB boot
- Network
- NAND environment
Signed-off-by: Lucas Stach <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
|
|
This patch remove the env saving in NAND as so far the
NAND driver is not ported to the M54418TWR platform.
Signed-off-by: Jason Jin <[email protected]>
|
|
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Wolfgang Grandegger <[email protected]>
|
|
|
|
|
|
SX1 does not build properly by itself, is not built
as part of MAKEALL arm or MAKEALL -a arm, and is only
present in Makefile, not boards.cfg. As it also has no
entry in MAINTAINERS, it is orphan and non-functional.
Remove it.
Signed-off-by: Albert ARIBAUD <[email protected]>
|
|
This driver is no longer used, remove it.
Signed-off-by: Marek Vasut <[email protected]>
|
|
This stuff has been rotting in the tree for a year now. Remove it.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Recent patches adding FSL_PMIC_I2C_LENGTH require
that the PMIC model is defined.
Signed-off-by: Stefano Babic <[email protected]>
CC: Jason Liu <[email protected]>
|
|
Allow booting a zImage kernel.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Allow booting a zImage kernel.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Allow booting a zImage kernel.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Allow booting a zImage kernel.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Allow booting a zImage kernel.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
mx25pdk has a Ethernet port that is connected to its internal FEC controller.
In order to power up the Ethernet PHY (DP83640) it is necessary to communicate
with the MC34704 PMIC via I2C.
Make the FEC ethernet port functional
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Add the register layout for the MC34704 PMIC from Freescale.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Introduce FSL_PMIC_I2C_LENGTH to configure the number of bytes that are used to
communicate with the PMIC via I2C.
Instead of hardcoding the value, pass the number via a configurable option per
PMIC type.
This will be useful for adding support for PMIC MC34704 from Freescale, which
uses only one byte in its I2C protocol.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
mx25pdk has a SD/MMC slot connected to esdhc1.
Add support for it and allow the environment variables to be saved into SD/MMC.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
It is necessary to include CONFIG_MX25 as several i.mx drivers handle the SoC
differences based on the this config option.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.
The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash
In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.
Signed-off-by: Stefano Babic <[email protected]>
|
|
|
|
|
|
Add targets of am335x_evm_uart{1,2,3,4,5} to have serial input/output on
UART{1,2,3,4,5} for use with the Beaglebone RS232 cape, am335x_evm
daughterboard, and other custom configurations.
Modify target for am335x_evm to include SERIAL1 and CONS_INDEX=1
options in order to clarify UART selection requirements.
Signed-off-by: Andrew Bradford <[email protected]>
|
|
This makes the FAT filesystem API more consistent with other block-based
filesystems. If in the future standard multi-filesystem commands such as
"ls" or "load" are implemented, having FAT work the same way as other
filesystems will be necessary.
Convert cmd_fat.c to the new API, so the code looks more like other files
implementing the same commands for other filesystems.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Benoît Thébaudeau <[email protected]>
|
